DTC P050A Cold Start Idle Air Control System Performance |

| DTC Code | DTC Detection Condition | Trouble Area |
| P050A | Insufficient mass air flow at cold start (2 trip detection logic) |
|
| Related DTCs | P050A: Cold start idle air speed control system |
| Required sensors/Components (Main) | Throttle body |
| Required sensors/Components (Related) | Mass air flow meter Engine coolant temperature sensor |
| Frequency of operation | Once per driving cycle |
| Duration | 10 seconds |
| MIL operation | 2 driving cycles |
| Sequence of operation | None |
| Monitor runs whenever following DTCs not present | P0010, P0020 (VVT Oil control valve) P0011, P0021 (VVT System - Advance) P0012, P0022 (VVT System - Retard) P0013, P0023 (Exhaust VVT Oil control valve) P0014, P0024 (Exhaust VVT System - Advance) P0015, P0025 (Exhaust VVT System - Retard) P0016, P0018 (VVT System - Misalignment) P0017, P0019 (Exhaust VVT System - Misalignment) P0102, P0103 (Mass air flow meter) P0115, P0117, P0118 (Engine coolant temperature sensor) P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle position sensor) P0125 (Insufficient coolant temperature for closed loop fuel control) P0171, P0172, P0174, P0175 (Fuel system) P0301 - P0308 (Misfire) P0335 (Crankshaft position sensor) P0340, P0342, P0343, P0345, P0347, P0348 (VVT sensor) P0351 - P0358 (Igniter) P0365, P0367, P0368, P0390, P0392, P0393 (Exhaust VVT sensor) P0500 (Vehicle speed sensor) P0705 (Shift lever position switch) P014C, P014D, P014E, P014F, P015A, P015B, P015C, P015D, P2195, P2196, P2197, P2198, P2237, P2238, P2239, P2240, P2241, P2242, P2252, P2253, P2255, P2256 (Air fuel ratio sensor) P1340 (Camshaft position sensor) |
| Battery voltage | 8 V or more |
| Time after engine start | 3 seconds or more |
| Starter | OFF |
| ECT at engine start | -10°C (14°F) or more |
| ECT | -10 to 50°C (14 to 122°F) |
| Engine idling | 3 seconds or more |
| Fuel-cut | OFF |
| Vehicle speed | Less than 3 km/h (1.875 mph) |
| Time after shift position changed | 2 seconds or more |
| Atmospheric pressure | 76 kPa (570 mmHg) or more |
| Accumulated mass air flow | Less than 116 g (varies with ECT) |

| Tester Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|
| 1.CHECK ANY OTHER DTCS OUTPUT |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read DTCs.
| Result | Proceed to |
| DTC P050A | A |
| DTC P050A and other DTCs | B |
|
| ||||
| OK | |
| 2.READ VALUE USING TECHSTREAM (FUEL TRIM) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream on.
Start the engine.
Enter the following menus: Powertrain / Engine and ECT / Data List / A/F Control System / Short FT #1 and Long FT #1, or Short FT #2 and Long FT #2.
Read the values displayed on the Techstream.
Add together the Short FT #1 and Long FT #1, or Short FT #2 and Long FT #2 values to obtain the total fuel trim.
|
| ||||
| OK | |
| 3.INSPECT THROTTLE BODY |
Check for deposits around the throttle valve and throttle valve condition.
|
| ||||
|
| ||||
| 4.REPAIR OR REPLACE THROTTLE BODY ASSEMBLY |
|
| ||||
| 5.CHECK PCV SYSTEM |
Check the PCV hose connections (Click here).
|
| ||||
| OK | |
| 6.CHECK AIR INDUCTION SYSTEM |
Check the air induction system for vacuum leakage .
|
| ||||
| OK | |
| 7.CHECK AIR CLEANER FILTER |
Visually check that the air cleaner filter is not excessively contaminated with dirt or oil.
|
| ||||
| OK | |
| 8.PERFORM ACTIVE TEST USING TECHSTREAM (OPERATE OCV) |
Connect the Techstream to the DLC3.
Start the engine.
Turn the Techstream on
Warm up the engine.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT Linear (Bank 1) or Control the VVT Linear (Bank 2).
Check the engine speed while operating the Oil Control Valve (OCV) using the Techstream.
| Operation | Specified Condition |
| 0% | Normal engine speed |
| 100% | Engine idles roughly or stalls |
|
| ||||
| OK | |
| 9.READ VALUE USING TECHSTREAM (MAF) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / MAF and Coolant Temp.
Allow the engine to idle until the Coolant Temp reaches 75°C (167°F) or more.
Read MAF with the engine speed at 3000 rpm.
|
| ||||
|
| ||||
| 10.REPAIR OR REPLACE PCV SYSTEM |
Repair or replace the PCV system.
|
| ||||
| 11.REPAIR OR REPLACE AIR INDUCTION SYSTEM |
Repair or replace the air induction system.
|
| ||||
| 12.REPLACE AIR CLEANER FILTER |
Replace the air cleaner filter element sub-assembly.
|
| ||||
| 13.CHECK AND REPAIR VVT SYSTEM |
Check and repair the VVT system.
| NEXT | |
| 14.CHECK WHETHER DTC OUTPUT RECURS (DTC P050A) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear DTCs (Click here).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Coolant Temp.
Check that the engine coolant temperature is between - 10°C and 50°C (14 and 122°F).
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P050A.
Check the DTC judgment result.
| Result | Proceed to |
| NORMAL (DTC is not output) | A |
| ABNORMAL (DTC P050A is output) | B |
|
| ||||
| A | ||
| ||
| 15.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER CONNECTOR CONNECTION) |
Check the connection and terminal contact pressure of connectors and wire harnesses between the mass air flow meter and ECM (Click here).
| NEXT | |
| 16.CHECK WHETHER DTC OUTPUT RECURS (DTC P050A) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear DTCs (Click here).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Coolant Temp.
Check that the engine coolant temperature is between - 10°C and 50°C (14 and 122°F).
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P050A.
Check the DTC judgment result.
| Result | Proceed to |
| ABNORMAL (DTC P050A is output) | A |
| NORMAL (DTC is not output) | B |
|
| ||||
| A | |
| 17.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM) |
Disconnect the D7 MAF meter connector.
Disconnect the D74 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D7-3 (VG) - D74-74 (VG) | Always | Below 1 Ω |
| D7-2 (E2G) - D74-75 (E2G) | Always | Below 1 Ω |
| D7-3 (VG) or D74-74 (VG) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 18.REPLACE MASS AIR FLOW METER |
Replace the mass air flow meter (Click here).
| NEXT | |
| 19.CHECK WHETHER DTC OUTPUT RECURS (DTC P050A) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear DTCs (Click here).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Coolant Temp.
Check that the engine coolant temperature is between - 10°C and 50°C (14 and 122°F).
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P050A.
Check the DTC judgment result.
| Result | Proceed to |
| NORMAL (DTC is not output) | A |
| ABNORMAL (DTC P050A is output) | B |
|
| ||||
| A | ||
| ||