Home › BODY › INSTRUMENT PANEL › INSTRUMENT PANEL SAFETY PAD (for Column Shift Type)

INSTRUMENT PANEL SAFETY PAD (for Column Shift Type) > INSTALLATION

for Preparation Click here


HINT:
A bolt without a torque specification is shown in the standard bolt chart (Click here).



1. INSTALL NO. 1 INSTRUMENT PANEL CLIP


  1. Attach the 2 claws to install the 2 clips.


    B227872



2. INSTALL NO. 3 INSTRUMENT PANEL STAY


  1. Attach the 3 claws to install the 3 stays.


    B227871



3. INSTALL INSTRUMENT PANEL SUB-ASSEMBLY
  1. Attach the 5 claws to install the instrument panel.

  1. Install the 3 bolts and 2 nuts.



  1. Install the 2 passenger airbag bolts.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }



    B232862

  1. Connect the connectors and attach the connectors to the clamps.



  1. Install the wire harness with the bolt.


    B161138



4. INSTALL FRONT NO. 4 SPEAKER ASSEMBLY (for 10 Speakers)


B165751E01
  1. Connect the connector.

  1. Temporarily install the speaker by aligning the positioning pins of the speaker with the instrument panel.

  1. Install the speaker with the 2 bolts.

    NOTICE:
    1. Do not touch the cone part of the speaker.
    2. When installing the speaker to the instrument panel, be careful that the wires do not get caught between the parts.



5. INSTALL NO. 3 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY


    B161134
  1. Attach the 6 clips and 2 claws to install the speaker panel.



6. INSTALL FRONT NO. 2 SPEAKER ASSEMBLY LH



B165750E01

  1. Connect the speaker connector.

  1. Temporarily install the speaker by aligning the positioning pins of the speaker with the instrument panel.

  1. Install the speaker with the 2 bolts.

    NOTICE:
    1. Do not touch the cone part of the speaker.
    2. When installing the speaker to the instrument panel, be careful that the wires do not get caught between the parts.



7. INSTALL NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY


    B161135
  1. Attach the 4 clips and claw to install the speaker panel.



8. INSTALL FRONT NO. 2 SPEAKER ASSEMBLY RH
  1. Connect the speaker connector.

  1. Temporarily install the speaker by aligning the positioning pins of the speaker with the instrument panel.

  1. Install the speaker with the 2 bolts.

    NOTICE:
    1. Do not touch the cone part of the speaker.
    2. When installing the speaker to the instrument panel, be careful that the wires do not get caught between the parts.



9. INSTALL INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY


    B161136
  1. Attach the 4 clips and claw to install the speaker panel.



10. INSTALL NO. 2 INSTRUMENT PANEL BOX DOOR SUB-ASSEMBLY


    B228244
  1. Install the box door with the 6 screws.



11. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY RH


    B230430
  1. Connect the connector.



    B226741
  1. Attach the 3 claws to install the finish panel.

  1. Install the 3 screws.

  1. Install the bolt.



12. INSTALL LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY


    B226008
  1. Connect the connector.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.

  1. Install the 3 bolts to install the instrument panel airbag.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



13. INSTALL LOWER INSTRUMENT PANEL


    B226759
  1. Attach the 2 claws.

  1. Install the panel with the bolt and screw.



14. INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY


    B226758
  1. Attach the 2 guides.

  1. Attach the 4 claws and clip to install the panel.



15. INSTALL FRONT PILLAR GARNISH RH

HINT:
Use the same procedures described for the LH side.



16. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH (for Regular Cab)
  1. Install the front door opening trim weatherstrip.



17. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH (for Double Cab, CrewMax)
  1. Install the rear door opening trim weatherstrip.



18. INSTALL COWL SIDE TRIM BOARD RH

HINT:
Use the same procedures described for the LH side.



19. INSTALL FRONT DOOR SCUFF PLATE RH (for Regular Cab)

HINT:
Use the same procedures described for the LH side.



20. INSTALL FRONT DOOR SCUFF PLATE RH (for Double Cab, CrewMax)

HINT:
Use the same procedures described for the LH side.



21. INSTALL INSTRUMENT SIDE PANEL RH


    B229198
  1. Attach the 6 claws to install the side panel.



22. INSTALL NAVIGATION RECEIVER ASSEMBLY WITH BRACKET (w/ Navigation System)


E232005
  1. Connect the connectors.

  1. Insert the navigation receiver as shown in the illustration to attach the 2 clips on its backside.

    NOTICE:
    When inserting the navigation receiver, do not press the knobs on it.



    E232001
  1. Install the navigation receiver with the 4 bolts.

    Torque:
    8.0 N*m{ 81 kgf*cm , 70 in.*lbf }



23. INSTALL RADIO RECEIVER ASSEMBLY WITH BRACKET (w/o USB Audio System)


    E161045
  1. Connect the connectors.

  1. Insert the radio receiver and attach the 3 clips on its backside.

    NOTICE:
    When inserting the radio receiver, do not press its knobs.



    B164786
  1. Install the radio receiver with the 4 bolts.



24. INSTALL RADIO RECEIVER ASSEMBLY WITH BRACKET (w/ USB Audio System)


    B230823
  1. Connect the connectors.

  1. Insert the radio receiver and attach the 3 clips on its backside.

    NOTICE:
    When inserting the radio receiver, do not press its knobs.



    B229224
  1. Install the radio receiver with the 4 bolts.



25. INSTALL INTEGRATION CONTROL AND PANEL ASSEMBLY (for Automatic Air Conditioning System)


B160588
  1. Connect the connectors.

  1. Attach the 4 clips to install the panel.



26. INSTALL INTEGRATION CONTROL AND PANEL ASSEMBLY (for Manual Air Conditioning System)


B160589
  1. Connect the connectors.

  1. Attach the 4 clips to install the panel.



27. INSTALL INSTRUMENT PANEL CUP HOLDER ASSEMBLY


    B161767
  1. Attach the 4 clips to install the cup holder.

  1. Install the 4 screws.



    B163941
  1. Attach the 2 claws to install the door box.



28. INSTALL LOWER INSTRUMENT CLUSTER FINISH PANEL


    B160587
  1. Connect the connectors.

  1. Attach the 4 clips to install the finish panel.

  1. Install the 2 screws.



29. INSTALL CENTER LOWER INSTRUMENT COVER


  1. Install the cover with the 2 clips.


    B171284E01



30. INSTALL COMBINATION METER ASSEMBLY


    B160584
  1. Connect the connector and clamp.

  1. Install the combination meter with the 4 screws.



31. INSTALL INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY


B227982
  1. Connect the connector and attach the wire harness clamp.

  1. Attach the 12 clips to install the finish panel.



32. INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY


    B225998
  1. Connect the connector.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.

  1. Attach the 2 claws to install the DLC3.

  1. Install the 4 bolts to install the instrument panel airbag.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



33. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY LH


    B163883
  1. for Automatic Air Conditioning System:
    Attach the 2 claws to install the sensor.



    B226740
  1. Connect the connectors.

  1. Attach the 9 clips and claw to install the finish panel.

  1. Install the 2 bolts.

  1. Install the hood lock control lever.



34. INSTALL INSTRUMENT SIDE PANEL LH


    B229058
  1. Attach the 7 claws to install the side panel.



35. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH (for Regular Cab)
  1. Install the front door opening trim weatherstrip.



36. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH (for Double Cab, CrewMax)
  1. Install the front door opening trim weatherstrip.



37. INSTALL FRONT PILLAR GARNISH LH
  1. Attach the claw to install the front pillar garnish.

  1. Install the assist grip with the 2 bolts.



  1. Attach the 2 claws to install the 2 assist grip plugs.


    B165706



38. INSTALL COWL SIDE TRIM BOARD LH


B165704
  1. Attach the 2 clips to install the cowl side trim board.

  1. Install the clip.



39. INSTALL FRONT DOOR SCUFF PLATE LH (for Regular Cab)


B165843
  1. Attach the 6 claws and 3 clips to install the front door scuff plate.



40. INSTALL FRONT DOOR SCUFF PLATE LH (for Double Cab, CrewMax)


B165841
  1. Attach the 6 claws and 3 clips to install the front door scuff plate.



41. INSTALL COLUMN SHIFT ASSEMBLY


C155886
  1. Using a T30 ''TORX'' wrench, install the column shift with the 3 bolts.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }

  1. Connect the connector and attach the harness clamp.



    C158379E01
  1. Connect the column shift transmission control cable end to the column shift.

    NOTICE:
    Make sure to install the cable end so that the inner cable is not twisted. Confirm that the cable end's ridged side is facing upward.



42. INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY


C154521
  1. Install the turn signal switch with spiral cable to the steering column with the clamp.



    C154522
  1. Connect the 5 connectors to the turn signal switch with spiral cable.



43. INSTALL UPPER STEERING COLUMN COVER


C154520
  1. Attach the claw to install the upper steering column cover.

  1. Attach the 4 clips.



44. INSTALL LOWER STEERING COLUMN COVER


C154519
  1. Attach the 2 claws to install the lower steering column cover.

  1. Install the 2 screws.

    Torque:
    2.0 N*m{ 20 kgf*cm , 18 in.*lbf }



45. INSTALL STEERING WHEEL ASSEMBLY


C159526E01
  1. Align the matchmarks on the steering wheel and steering main shaft.

  1. Install the steering wheel set nut.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }



46. INSTALL STEERING PAD (w/o Steering Pad Switch)


    B166435
  1. Support the steering pad with one hand.

  1. Connect the 2 connectors to the steering pad.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.

  1. Confirm that the circumference groove of the screw fits in the screw case, and place the steering pad onto the steering wheel.

  1. Using a T30 "TORX" socket wrench, tighten the 2 screws.

    Torque:
    8.8 N*m{ 90 kgf*cm , 78 in.*lbf }



47. INSTALL STEERING PAD (w/ Steering Pad Switch)


    B166581
  1. Support the steering pad with one hand.

  1. Connect the 2 connectors to the steering pad.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.

  1. Confirm that the circumference groove of the screw fits in the screw case, and place the steering pad onto the steering wheel .

  1. Using a T30 "TORX" socket wrench, tighten the 2 screws.

    Torque:
    8.8 N*m{ 90 kgf*cm , 78 in.*lbf }



48. INSTALL LOWER NO. 3 STEERING WHEEL COVER


    B166432
  1. Attach the 2 claws to install the cover.



49. INSTALL LOWER NO. 2 STEERING WHEEL COVER


    B166433
  1. w/ Cruise Control:

    1. Attach the 2 claws to install the cover.



    B167059
  1. w/o Cruise Control:

    1. Attach the 2 claws to install the cover.



50. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL


51. CHECK SRS WARNING LIGHT
  1. Check the SRS warning light (Click here).