Home › BODY › INSTRUMENT PANEL › INSTRUMENT PANEL SAFETY PAD (for Column Shift Type)

INSTRUMENT PANEL SAFETY PAD (for Column Shift Type) > REMOVAL

for Preparation Click here



1. TABLE OF BOLT, SCREW AND NUT


HINT:
All bolts, screws and nuts relevant to installing and removing the instrument panel are shown along with their alphabet code below.



B232863E01



2. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).



3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Turn the ignition switch OFF and disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.



4. REMOVE LOWER NO. 2 STEERING WHEEL COVER


    B166433
  1. w/ Cruise Control:

    1. Using a screwdriver, remove the No. 2 steering wheel cover.

      HINT:
      Tape the screwdriver tip before use.



    B167059
  1. w/o Cruise Control:

    1. Using a screwdriver, remove the No. 2 steering wheel cover.

      HINT:
      Tape the screwdriver tip before use.



5. REMOVE LOWER NO. 3 STEERING WHEEL COVER


    B166432
  1. Using a screwdriver, remove the steering wheel cover.

    HINT:
    Tape the screwdriver tip before use.



6. REMOVE STEERING PAD (w/o Steering Pad Switch)


    B166580E01
  1. Using a T30 "TORX" socket wrench, loosen the 2 screws until the groove along the screw circumference catches on the screw case.



    B166581
  1. Pull out the steering pad from the steering wheel, as shown in the illustration. Then support the steering pad with one hand.

    NOTICE:
    When removing the steering pad, do not pull the airbag wire harness.

  1. Disconnect the 2 connectors and remove the steering pad.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.



7. REMOVE STEERING PAD (w/ Steering Pad Switch)


    B166580E01
  1. Using a T30 "TORX" socket wrench, loosen the 2 screws until the groove along the screw circumference catches on the screw case.



    B166581
  1. Pull out the steering pad from the steering wheel, as shown in the illustration. Then support the steering pad with one hand.

    NOTICE:
    When removing the steering pad, do not pull the airbag wire harness.

  1. Disconnect the 2 connectors and remove the steering pad.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.



8. REMOVE STEERING WHEEL ASSEMBLY
  1. Remove the steering wheel set nut.



    C154517E01
  1. Put matchmarks on the steering wheel and main shaft.

  1. Using SST, remove the steering wheel.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05011)



9. REMOVE LOWER STEERING COLUMN COVER


C159214
  1. Remove the 2 screws.

  1. Detach the 2 claws to remove the lower steering column cover.



10. REMOVE UPPER STEERING COLUMN COVER


    C154520
  1. Detach the 4 clips.

  1. Detach the claw to remove the upper steering column cover.



11. REMOVE TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY


C154522
  1. Disconnect the 5 connectors from the turn signal switch with spiral cable.



    C154521
  1. Using pliers, grip the claws of the clamp and remove the turn signal switch with spiral cable from the steering column.



12. REMOVE COLUMN SHIFT ASSEMBLY
  1. Move the shift lever to the N position.



    C155885
  1. Disconnect the column shift transmission control cable end from the column shift.



    C155886
  1. Disconnect the connector and detach the harness clamp.

  1. Using a T30 "TORX" wrench, remove the 3 bolts and column shift.



13. REMOVE FRONT DOOR SCUFF PLATE LH (for Regular Cab)


B165843
  1. Detach the 6 claws and 3 clips, and remove the front door scuff plate.



14. REMOVE FRONT DOOR SCUFF PLATE LH (for Double Cab, CrewMax)


B165841
  1. Detach the 6 claws and 3 clips, and remove the front door scuff plate.



15. REMOVE COWL SIDE TRIM BOARD LH


B165704
  1. Remove the clip.

  1. Detach the 2 clips and remove the cowl side trim board.



16. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH (for Regular Cab)
  1. Remove the front door opening trim weatherstrip.



17. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH (for Double Cab, CrewMax)
  1. Remove the front door opening trim weatherstrip.



18. REMOVE FRONT PILLAR GARNISH LH
  1. Using a screwdriver, detach the 2 claws and remove the 2 assist grip plugs.

    HINT:
    Tape the screwdriver tip before use.

  1. Remove the 2 bolts and assist grip.



  1. Detach the claw and remove the front pillar garnish.


    B165705E08



    B165709E06
  1. Protect the curtain shield airbag.

    1. Thoroughly cover the airbag with a cloth or nylon sheet and fix the ends of the cover with adhesive tape, as shown in the illustration.

      NOTICE:
      Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.



19. REMOVE INSTRUMENT SIDE PANEL LH


    B226739
  1. Using a moulding remover, detach the 7 claws and remove the side panel.



20. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY LH


    B226740
  1. Remove the hood lock control lever.

  1. Remove the 2 bolts.

  1. Detach the 9 clips and claw.



    B163883
  1. for Automatic Air Conditioning System:
    Detach the 2 claws and remove the sensor.

  1. Remove the finish panel and then disconnect the connectors.



21. REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY


    B225997
  1. Remove the 4 bolts and remove the instrument panel airbag.

  1. Detach the 2 claws and disconnect the DLC3.

  1. Disconnect the connector.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.



22. REMOVE INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY


    B227982
  1. Disconnect the connector and detach the wire harness clamp.

  1. Detach the 12 clips and remove the finish panel.



23. REMOVE COMBINATION METER ASSEMBLY


    B160584
  1. Remove the 4 screws.

  1. Disconnect the connector and clamp, and remove the combination meter.



24. REMOVE CENTER LOWER INSTRUMENT COVER


  1. Remove the 2 clips and cover.


    B171284E01



25. REMOVE LOWER INSTRUMENT CLUSTER FINISH PANEL


    B160587
  1. Remove the 2 screws.

  1. Detach the 4 clips.

  1. Remove the finish panel and then disconnect the connectors.



26. REMOVE INSTRUMENT PANEL CUP HOLDER ASSEMBLY


    B161766
  1. Detach the 2 claws and remove the door box.



    B161767
  1. Remove the 4 screws.

  1. Detach the 4 clips and remove the cup holder.



27. REMOVE INTEGRATION CONTROL AND PANEL ASSEMBLY (for Manual Air Conditioning System)


    B160589
  1. Detach the 4 clips.

  1. Remove the panel and then disconnect the connectors.



28. REMOVE INTEGRATION CONTROL AND PANEL ASSEMBLY (for Automatic Air Conditioning System)


    B160588
  1. Detach the 4 clips.

  1. Remove the panel and then disconnect the connectors.



29. REMOVE RADIO RECEIVER ASSEMBLY WITH BRACKET (w/o USB Audio System)


    B164786
  1. Remove the 4 bolts.



    E159007
  1. Pull the radio receiver to detach the 3 clips on the backside of the radio receiver.

  1. Disconnect the connectors and remove the radio receiver.



30. REMOVE RADIO RECEIVER ASSEMBLY WITH BRACKET (w/ USB Audio System)


    B229224
  1. Remove the 4 bolts.



    B229225
  1. Pull the radio receiver to detach the 3 clips on the backside of the radio receiver.

  1. Disconnect the connectors and remove the radio receiver.



31. REMOVE NAVIGATION RECEIVER ASSEMBLY WITH BRACKET (w/ Navigation System)


    E232001
  1. Remove the 4 bolts.



    E232002
  1. Pull the navigation receiver as shown in the illustration to detach the 2 clips on the backside of the navigation receiver.

  1. Disconnect the connectors and remove the navigation receiver.



32. REMOVE INSTRUMENT SIDE PANEL RH


    B229197
  1. Using a moulding remover, detach the 6 claws and remove the side panel.



33. REMOVE FRONT DOOR SCUFF PLATE RH (for Regular Cab)

HINT:
Use the same procedures described for the LH side.



34. REMOVE FRONT DOOR SCUFF PLATE RH (for Double Cab, CrewMax)

HINT:
Use the same procedures described for the LH side.



35. REMOVE COWL SIDE TRIM BOARD RH

HINT:
Use the same procedures described for the LH side.



36. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH (for Regular Cab)
  1. Remove the front door opening trim weatherstrip.



37. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH (for Double Cab, CrewMax)
  1. Remove the front door opening trim weatherstrip.



38. REMOVE FRONT PILLAR GARNISH RH

HINT:
Use the same procedures described for the LH side.



39. REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY


    B226758
  1. Detach the clip and 4 claws.

  1. Detach the 2 guides and remove the panel.



40. REMOVE LOWER INSTRUMENT PANEL


    B226759
  1. Remove the screw and bolt.

  1. Detach the 2 claws and remove the panel.



41. REMOVE LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY


    B226007
  1. Remove the 3 bolts and remove the instrument panel airbag.

  1. Disconnect the connector.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.



42. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY RH


    B226741
  1. Remove the bolt.

  1. Remove the 3 screws.

  1. Detach the 3 claws and remove the finish panel.



    B230430
  1. Disconnect the connector.



43. REMOVE NO. 2 INSTRUMENT PANEL BOX DOOR SUB-ASSEMBLY


    B228244
  1. Remove the 6 screws and box door.



44. REMOVE INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY


    B161136
  1. Using a screwdriver, detach the 4 clips and claw, and remove the speaker panel.

    HINT:
    Tape the screwdriver tip before use.



45. REMOVE FRONT NO. 2 SPEAKER ASSEMBLY LH



B165750E01

  1. Remove the 2 bolts.

  1. Remove the speaker and disconnect the connector.

    NOTICE:
    Do not touch the cone part of the speaker.



46. REMOVE NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY


    B161135
  1. Using a screwdriver, detach the 4 clips and claw, and remove the speaker panel.

    HINT:
    Tape the screwdriver tip before use.



47. REMOVE FRONT NO. 2 SPEAKER ASSEMBLY RH
  1. Remove the 2 bolts.

  1. Remove the speaker and disconnect the connector.



48. REMOVE NO. 3 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY


    B161134
  1. Using a screwdriver, detach the 6 clips and 2 claws, and remove the speaker panel.

    HINT:
    Tape the screwdriver tip before use.



49. REMOVE FRONT NO. 4 SPEAKER ASSEMBLY (for 10 Speakers)


B165751E01
  1. Remove the 2 bolts.

  1. Remove the speaker and disconnect the connector.

    NOTICE:
    Do not touch the cone part of the speaker.



50. REMOVE INSTRUMENT PANEL SUB-ASSEMBLY
  1. Detach the connectors from the clamps and disconnect the connectors.



  1. Remove the bolt and wire harness.


    B161138

  1. Remove the 2 passenger airbag bolts.

  1. Remove the 3 bolts and 2 nuts.



  1. Detach the 5 claws and remove the instrument panel.


    B232694



51. REMOVE NO. 3 INSTRUMENT PANEL STAY


  1. Detach the 3 claws and remove the 3 stays.


    B227871



52. REMOVE NO. 1 INSTRUMENT PANEL CLIP


  1. Detach the 2 claws and remove the 2 clips.


    B227872