Home › BODY › INSTRUMENT PANEL › INSTRUMENT PANEL SAFETY PAD (for Floor Shift Type)

INSTRUMENT PANEL SAFETY PAD (for Floor Shift Type) > REMOVAL

for Preparation Click here



1. TABLE OF BOLT, SCREW AND NUT


HINT:
All bolts, screws and nuts relevant to installing and removing the instrument panel are shown along with their alphabet code below.



B232863E01



2. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).



3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Turn the ignition switch OFF and disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.



4. REMOVE LOWER NO. 2 STEERING WHEEL COVER


    B166433
  1. w/ Cruise Control:

    1. Using a screwdriver, remove the No. 2 steering wheel cover.

      HINT:
      Tape the screwdriver tip before use.



    B167059
  1. w/o Cruise Control:

    1. Using a screwdriver, remove the No. 2 steering wheel cover.

      HINT:
      Tape the screwdriver tip before use.



5. REMOVE LOWER NO. 3 STEERING WHEEL COVER


    B166432
  1. Using a screwdriver, remove the steering wheel cover.

    HINT:
    Tape the screwdriver tip before use.



6. REMOVE STEERING PAD (w/o Steering Pad Switch)


    B166434E01
  1. Using a T30 "TORX" socket wrench, loosen the 2 screws until the groove along the screw circumference catches on the screw case.



    B166435
  1. Pull out the steering pad from the steering wheel, as shown in the illustration. Then support the steering pad with one hand.

    NOTICE:
    When removing the steering pad, do not pull the airbag wire harness.

  1. Disconnect the 2 connectors and remove the steering pad.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.



7. REMOVE STEERING PAD (w/ Steering Pad Switch)


    B166580E01
  1. Using a T30 "TORX" socket wrench, loosen the 2 screws until the groove along the screw circumference catches on the screw case.



    B166581
  1. Pull out the steering pad from the steering wheel, as shown in the illustration. Then support the steering pad with one hand.

    NOTICE:
    When removing the steering pad, do not pull the airbag wire harness.

  1. Disconnect the 2 connectors and remove the steering pad.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.



8. REMOVE STEERING WHEEL ASSEMBLY
  1. Remove the steering wheel set nut.



    C154517E01
  1. Put matchmarks on the steering wheel and main shaft.

  1. Using SST, remove the steering wheel.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05011)



9. REMOVE LOWER STEERING COLUMN COVER (for Manual Tilt and Manual Telescopic Steering Column)


C154519
  1. Remove the 2 screws.

  1. Detach the 2 claws to remove the lower steering column cover.



10. REMOVE LOWER STEERING COLUMN COVER (for Power Tilt and Power Telescopic Steering Column)


C154519
  1. Remove the 2 screws.

  1. Detach the 2 claws to remove the lower steering column cover.



11. REMOVE UPPER STEERING COLUMN COVER (for Manual Tilt and Manual Telescopic Steering Column)


    C159215
  1. Detach the 4 clips.

  1. Detach the claw to remove the upper steering column cover.



12. REMOVE UPPER STEERING COLUMN COVER (for Power Tilt and Power Telescopic Steering Column)


    C159215
  1. Detach the 4 clips.

  1. Detach the claw to remove the upper steering column cover.



13. REMOVE TILT AND TELESCOPIC MANUAL SWITCH (for Power Tilt and Power Telescopic Steering Column)


C159804
  1. Disconnect the connector.

  1. Using a screwdriver, detach the claw and pull out the tilt and telescopic switch.

    NOTICE:
    Pushing on the claw too hard will break the claw.

    HINT:
    Tape the screwdriver tip before use.



14. REMOVE TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY


C154522
  1. Disconnect the 5 connectors from the combination switch with spiral cable.



    C159216
  1. Using pliers, grip the claws of the clamp and remove the combination switch with spiral cable from the steering column.



15. REMOVE FRONT DOOR SCUFF PLATE LH (for Regular Cab)


B165843
  1. Detach the 6 claws and 3 clips, and remove the front door scuff plate.



16. REMOVE FRONT DOOR SCUFF PLATE LH (for Double Cab, CrewMax)


B165841
  1. Detach the 6 claws and 3 clips, and remove the front door scuff plate.



17. REMOVE COWL SIDE TRIM BOARD LH


B165704
  1. Remove the clip.

  1. Detach the 2 clips and remove the cowl side trim board.



18. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH (for Regular Cab)
  1. Remove the front door opening trim weatherstrip.



19. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH (for Double Cab, CrewMax)
  1. Remove the front door opening trim weatherstrip.



20. REMOVE FRONT PILLAR GARNISH LH
  1. Using a screwdriver, detach the 2 claws and remove the 2 assist grip plugs.

    HINT:
    Tape the screwdriver tip before use.

  1. Remove the 2 bolts and assist grip.



  1. Detach the claw and remove the front pillar garnish.


    B165705E08



    B165709E06
  1. Protect the curtain shield airbag.

    1. Thoroughly cover the airbag with a cloth or nylon sheet and fix the ends of the cover with adhesive tape, as shown in the illustration.

      NOTICE:
      Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.



21. REMOVE INSTRUMENT SIDE PANEL LH


    B226739
  1. Using a moulding remover, detach the 7 claws and remove the side panel.



22. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY LH


    B226740
  1. Remove the hood lock control lever.

  1. Remove the 2 bolts.

  1. Detach the 9 clips and claw.



    B163883
  1. for Automatic Air Conditioning System:
    Detach the 2 claws and remove the sensor.

  1. Remove the finish panel and then disconnect the connectors.



23. REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY


    B225997
  1. Remove the 4 bolts and remove the instrument panel airbag.

  1. Detach the 2 claws and disconnect the DLC3.

  1. Disconnect the connector.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.



24. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY


    B161741
  1. Twist the shift lever knob in the direction indicated by the arrow and remove it.



25. REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY


    B161742
  1. Detach the 12 clips and remove the console panel.



26. REMOVE REAR UPPER CONSOLE PANEL SUB-ASSEMBLY
  1. Remove the clip.

  1. Detach the 6 clips and remove the console panel.



  1. w/ Trailer Towing System:
    Disconnect the connector


    B171298



27. REMOVE REAR CONSOLE END PANEL SUB-ASSEMBLY


    B227980
  1. Using a moulding remover, detach the 7 clips and remove the end panel.

  1. except Regular Cab:
    Detach the 2 wire harness clamps and disconnect the connector.



28. REMOVE CONSOLE BOX CARPET


29. REMOVE REAR CONSOLE BOX ASSEMBLY


    B227981
  1. Remove the 2 screws.

  1. Detach the 2 wire harness clamps.

  1. Remove the 4 bolts and rear console box.



30. REMOVE FRONT CONSOLE BOX


    B161746
  1. Remove the 2 clips.

  1. Remove the 6 screws and front console box.



31. REMOVE INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY


    B227982
  1. Disconnect the connector and detach the wire harness clamp.

  1. Detach the 12 clips and remove the finish panel.



32. REMOVE COMBINATION METER ASSEMBLY


    B160584
  1. Remove the 4 screws.

  1. Disconnect the connector and detach the wire harness clamp, and remove the combination meter.



33. REMOVE CENTER LOWER INSTRUMENT PANEL FINISH PANEL


    B161747
  1. Detach the 4 clips and remove the finish panel.

  1. Disconnect the connectors.



34. REMOVE INTEGRATION CONTROL AND PANEL ASSEMBLY (for Manual Air Conditioning System)


    B160589
  1. Detach the 4 clips and remove the panel.

  1. Disconnect the connectors.



35. REMOVE INTEGRATION CONTROL AND PANEL ASSEMBLY (for Automatic Air Conditioning System)


    B160588
  1. Detach the 4 clips and remove the panel.

  1. Disconnect the connectors.



36. REMOVE RADIO RECEIVER ASSEMBLY WITH BRACKET (w/o USB Audio System)


    B164786
  1. Remove the 4 bolts.



    E159007
  1. Pull the radio receiver to detach the 3 clips on the backside of the radio receiver.

  1. Disconnect the connectors and remove the radio receiver.



37. REMOVE RADIO RECEIVER ASSEMBLY WITH BRACKET (w/ USB Audio System)


    B229224
  1. Remove the 4 bolts.



    B229225
  1. Pull the radio receiver to detach the 3 clips on the backside of the radio receiver.

  1. Disconnect the connectors and remove the radio receiver.



38. REMOVE NAVIGATION RECEIVER ASSEMBLY WITH BRACKET (w/ Navigation System)
  1. for DVD:
    Remove the navigation receiver assembly with bracket .

  1. for SD:
    Remove the navigation receiver assembly with bracket .



39. REMOVE INSTRUMENT SIDE PANEL RH


    B229197
  1. Using a moulding remover, detach the 6 claws and remove the side panel.



40. REMOVE FRONT DOOR SCUFF PLATE RH (for Regular Cab)

HINT:
Use the same procedures described for the LH side.



41. REMOVE FRONT DOOR SCUFF PLATE RH (for Double Cab, CrewMax)

HINT:
Use the same procedures described for the LH side.



42. REMOVE COWL SIDE TRIM BOARD RH

HINT:
Use the same procedures described for the LH side.



43. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH (for Regular Cab)
  1. Remove the front door opening trim weatherstrip.



44. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH (for Double Cab, CrewMax)
  1. Remove the front door opening trim weatherstrip.



45. REMOVE FRONT PILLAR GARNISH RH

HINT:
Use the same procedures described for the LH side.



46. REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY


    B226758
  1. Detach the clip and 4 claws.

  1. Detach the 2 guides and remove the cover.



47. REMOVE LOWER INSTRUMENT PANEL


    B226759
  1. Remove the screw and bolt.

  1. Detach the 2 claws and remove the panel.



48. REMOVE LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY


    B226007
  1. Remove the 3 bolts and remove the instrument panel airbag.

  1. Disconnect the connector.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.



49. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY RH


    B226741
  1. Remove the bolt and 3 screws.

  1. Detach the 3 claws.



    B230430
  1. Disconnect the connector.



50. REMOVE NO. 2 INSTRUMENT PANEL BOX DOOR SUB-ASSEMBLY


    B228244
  1. Remove the 6 screws and box door.



51. REMOVE INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY


    B161136
  1. Using a screwdriver, detach the 4 clips and claw, and remove the speaker panel.

    HINT:
    Tape the screwdriver tip before use.



52. REMOVE FRONT NO. 2 SPEAKER ASSEMBLY LH



B165750E01

  1. Remove the 2 bolts.

  1. Remove the speaker and disconnect the connector.

    NOTICE:
    Do not touch the cone part of the speaker.



53. REMOVE NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY


    B161135
  1. Using a screwdriver, detach the 4 clips and claw, and remove the speaker panel.

    HINT:
    Tape the screwdriver tip before use.



54. REMOVE FRONT NO. 2 SPEAKER ASSEMBLY RH
  1. Remove the 2 bolts.

  1. Remove the speaker and disconnect the connector.

    NOTICE:
    Do not touch the cone part of the speaker.



55. REMOVE NO. 3 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY


    B161134
  1. Using a screwdriver, detach the 6 clips and 2 claws, and remove the speaker panel.

    HINT:
    Tape the screwdriver tip before use.



56. REMOVE FRONT NO. 4 SPEAKER ASSEMBLY (for 10 Speakers)


B165751E01
  1. Remove the 2 bolts.

  1. Remove the speaker and disconnect the connector.

    NOTICE:
    Do not touch the cone part of the speaker.



57. REMOVE INSTRUMENT PANEL SUB-ASSEMBLY
  1. Detach the connectors from the clamps and disconnect the connectors.



  1. Remove the bolt and wire harness.


    B161138

  1. Remove the 2 passenger airbag bolts.

  1. Remove the 3 bolts and 2 nuts.



  1. Detach the 5 claws and remove the instrument panel.


    B232694



58. REMOVE NO. 3 INSTRUMENT PANEL STAY


  1. Detach the 3 claws and remove the 3 stays.


    B227871



59. REMOVE NO. 1 INSTRUMENT PANEL CLIP


  1. Detach the 2 claws and remove the 2 clips.


    B227872