POWER DOOR LOCK CONTROL SYSTEM > Door Control Switch Circuit |


| 1.READ VALUE USING TECHSTREAM (DOOR CONTROL SWITCH) |
Check the Data List to ensure proper functioning of the door control switch.
| Tester Display | Measurement item/Range | Normal Condition | Diagnostic Note |
| Door Lock SW-Lock | Door control switch lock signal / ON or OFF | ON: Door control switch is pushed to lock position OFF: Door control switch is not pushed | - |
| Door Lock SW-Unlock | Door control switch unlock signal / ON or OFF | ON: Door control switch is pushed to unlock position OFF: Door control switch is not pushed | - |
| Result | Proceed to |
| OK | A |
| NG (for Driver Side) | B |
| NG (for Passenger Side) | C |
|
| ||||
|
| ||||
| A | ||
| ||
| 2.INSPECT POWER WINDOW REGULATOR MASTER SWITCH |

Remove the master switch (Click here).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 1 (L) - 7 (E) | Lock | Below 1 Ω |
| 1 (L) - 7 (E) | OFF (Free) | 10 kΩ or higher |
| 9 (UL) - 7 (E) | ||
| 9 (UL) - 7 (E) | Unlock | Below 1 Ω |
| Tester Connection | Switch Condition | Specified Condition |
| 2 (L) - 1 (E) | Lock | Below 1 Ω |
| 2 (L) - 1 (E) | OFF (Free) | 10 kΩ or higher |
| 9 (UL) - 1 (E) | ||
| 9 (UL) - 1 (E) | Unlock | Below 1 Ω |
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (DOOR LOCK SWITCH - MAIN BODY ECU) |

Disconnect the N2 switch connector.
Disconnect the DD ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| N2-1 (L) - DD-49 (L1) | Always | Below 1 Ω |
| N2-9 (UL) - DD-52 (UL1) | ||
| N2-7 (E) - Body ground | ||
| DD-49 (L1) - Body ground | Always | 10 kΩ or higher |
| DD-52 (UL1) - Body ground |
| Tester Connection | Condition | Specified Condition |
| N2-2 (L) - DD-49 (L1) | Always | Below 1 Ω |
| N2-9 (UL) - DD-52 (UL1) | ||
| N2-1 (E) - Body ground | ||
| DD-49 (L1) - Body ground | Always | 10 kΩ or higher |
| DD-52 (UL1) - Body ground |
|
| ||||
| OK | ||
| ||
| 4.INSPECT DOOR CONTROL SWITCH |
![]() |
Remove the door control switch (Click here ).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 4 (L) - 3 (E) | Lock | Below 1 Ω |
| 4 (L) - 3 (E) | OFF | 10 kΩ or higher |
| 2 (UL) - 3 (E) | ||
| 2 (UL) - 3 (E) | Unlock | Below 1 Ω |
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (FRONT DOOR CONTROL SWITCH RH - MAIN BODY ECU AND BODY GROUND) |

Disconnect the M5 switch connector.
Disconnect the DD ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| M5-4 (L) - DD-49 (L1) | Always | Below 1 Ω |
| M5-2 (UL) - DD-40 (UL1) | ||
| M5-3 (E) - Body ground | ||
| DD-49 (L1) - Body ground | Always | 10 kΩ or higher |
| DD-40 (UL1) - Body ground |
|
| ||||
| OK | ||
| ||