Home › COMMUNICATION SYSTEM › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > FAIL-SAFE CHART

for Preparation Click here



FAIL-SAFE FUNCTION
  1. When communication fails in any of the main wires (communication lines) due to a short circuit or other causes, the fail-safe function, which is specified for each system, operates to prevent the system from malfunctioning.

  2. The table below shows the effects on each system when communication is impossible. For further details, refer to each system.

    Function
    Behavior during CAN Failure
    1. Control Master
    2. System Related
    Vehicle Behavior
    Indicator and Buzzer
    Diagnostic Trouble Code
    VFC control
    (Changes the power steering fluid flow according to the state of the vehicle using the vehicle speed, engine speed, steering angle and towing information.)
    1. Power steering ECU
    2. ECM, Skid control ECU with actuator, Steering angle sensor
    Alternative control (The steering angle, vehicle speed and engine speed are fixed.)
    PPS indicator light turns on
    U0073
    Air conditioning control
    (Performs engine-linked control based on sensor information and controls the air conditioning and panel.)
    1. Air conditioning amplifier
    2. Main body ECU, ECM, Combination meter ECU, Bus buffer ECU
    Maintains previous values.
    Nothing
    Nothing
    Driver side seat memory system
    (Memorizes and recalls the driver side seat, steering wheel and outside mirror positions.)
    1. Front power seat control ECU and switch LH
    2. Outer mirror control ECU, Multiplex tilt and telescopic ECU, Main body ECU, ECM, Combination meter ECU
    Position memorization and recall cannot be performed. The tilt and telescopic system does not operate.
    Nothing
    Nothing
    2WD-4WD switching limitation
    (Switching between 2WD and 4WD is prohibited when the vehicle speed is outside the acceptable range.)
    1. 4WD control ECU
    2. Skid control ECU with actuator
    Switching between 2WD and 4WD is prohibited.
    Indicator light blinks
    Nothing
    High-Low switching limitation
    (Prohibits High-Low switching when the vehicle speed or engine speed is outside the acceptable range or the A/T is not in N during the A/T status check.)
    1. 4WD control ECU
    2. ECM, Skid control ECU with actuator
    High-Low switching is prohibited.
    Indicator light blinks
    Nothing
    Control performed during low temperatures
    (Changes the value of the electric current applied to the ACT according to the temperature.)
    1. 4WD control ECU
    2. ECM, Air conditioning amplifier
    Changes to the temperature used for ACT temperature correction control calculations.
    Nothing
    Nothing
    Vehicle speed threshold limitation
    (Determines whether the temperature is low or normal and changes the vehicle speed at which shifting from to 2 to 4 is prohibited.)
    1. 4WD control ECU
    2. Air conditioning amplifier
    Uses the threshold value for low temperatures.
    Nothing
    Nothing
    Indicator and buzzer signal output
    (Outputs a signal indicating the state of the indicators and buzzers, which represent the actuator position and switching status.)
    1. 4WD control ECU
    2. -
    The signal cannot be transmitted. Therefore, the signal is not updated.
    Nothing
    Nothing
    Cruise control cancel signal output
    (Outputs a cruise control cancel signal when center differential switching is not completed even though 5 seconds or more have elapsed from the start of switching.)
    1. 4WD control ECU
    2. -
    The signal cannot be transmitted. Therefore, the signal is not updated.
    Nothing
    Nothing
    L4 state signal output
    (Outputs a signal when switching to the L4 position is finished.)
    1. 4WD control ECU
    2. -
    The signal cannot be transmitted. Therefore, the signal is not updated.
    Nothing
    Nothing
    4WD state signal output
    (The ADDSW state is output.)
    1. 4WD control ECU
    2. -
    The signal cannot be transmitted. Therefore, the signal is not updated.
    Nothing
    Nothing
    T/FN state signal output
    (The NPSW state is output.)
    1. 4WD control ECU
    2. -
    The signal cannot be transmitted. Therefore, the signal is not updated.
    Nothing
    Nothing
    Signal output during switching
    (Outputs the state of electric current being applied to the actuator.)
    1. 4WD control ECU
    2. -
    The signal cannot be transmitted. Therefore, the signal is not updated.
    Nothing
    Nothing
    Electrical load control
    (Performs idle up according to electrical load, etc.)
    1. ECM
    2. Main body ECU, Air conditioning amplifier
    Idle up according to the electrical load is not performed.
    Nothing
    Nothing
    Air conditioning-linked control
    (Performs idle up according to the compressor load, and performs air conditioning cut control.)
    1. ECM
    2. Air conditioning amplifier
    Air conditioning-linked control does not operate.
    Nothing
    Nothing
    Charging control
    (Performs idle up according to charging requests.)
    1. ECM
    2. Main body ECU, Air conditioning amplifier
    Idle up according to charging requests is not performed.
    Nothing
    Nothing
    Integrated control (VDM)
    (Estimates driver requested torque based on accelerator pedal operation and performs torque characteristic control according to driving conditions so that drivability, acceleration performance and acceleration feeling are improved.)
    1. ECM
    2. Skid control ECU with actuator, Steering angle sensor
    Integrated control is not performed.
    Nothing
    Nothing
    ECT system indicators
    (Indicate the shift position, states of switches, system modes, etc.)
    1. ECM
    2. Main body ECU, Combination meter ECU
    Indicators do not turn on.
    Nothing
    Nothing
    AI-SHIFT control
    (Controls the A/T in order to improve engine braking power and acceleration feeling.)
    1. ECM
    2. Skid control ECU with actuator
    AI-SHIFT control does not operate.
    Nothing
    Nothing
    Coast downshift
    (Changes the coast down shift point according to the heater requested upshift delay.) (Performs heater requested upshift delay.)
    1. ECM
    2. Air conditioning amplifier
    Coast downshift does not operate.
    Nothing
    Nothing
    Cruise control
    (Adjusts the engine throttle valve opening amount automatically to control the vehicle.)
    1. ECM
    2. Skid control ECU with actuator, Combination meter ECU
    Cruise control does not operate.
    Nothing
    Nothing
    ABS control
    (Monitors for tire slippage and performs fluid pressure control to prevent the wheels from locking up in order to maintain vehicle stability and vehicle body deceleration.)
    1. Skid control ECU with actuator
    2. 4WD control ECU
    The ABS does not operate.
    ABS warning light turns on.
    U0073
    MSR control
    (Prevents the tires from slipping due to engine drag torque by increasing engine torque.)
    1. Skid control ECU with actuator
    2. ECM, Steering angle sensor, 4WD control ECU
    MSR does not operate.
    Light turns on.
    1. U0073
    2. U0100
    3. U0114
    4. U0123
    5. U0126
    TCS control
    (Prevents excessive tire slippage due to engine torque by decreasing engine torque and increasing pressure to the brakes.)
    1. Skid control ECU with actuator
    2. ECM, Steering angle sensor, 4WD control ECU
    TCS does not operate.
    Light turns on.
    1. U0073
    2. U0100
    3. U0114
    4. U0123
    5. U0126
    VSC control
    (Reduces excess yaw by increasing brake pressure, and induces necessary yaw by increasing brake pressure and reducing engine torque.)
    1. Skid control ECU with actuator
    2. ECM, Steering angle sensor, 4WD control ECU
    VSC does not operate.
    Light turns on.
    1. U0073
    2. U0100
    3. U0114
    4. U0123
    5. U0126
    Manual mirror adjustment control
    (Adjusts the outer mirrors according to the auto mirror switch operation.)
    1. Outer mirror control ECU
    2. Main body ECU
    Manual control is stopped.
    Nothing
    Nothing
    Mirror position memorization control
    (Memorizes the current mirror position.)
    1. Outer mirror control ECU
    2. Front power seat control ECU and switch LH, Main body ECU
    Memorization control is prohibited.
    Nothing
    Nothing
    Mirror position recall control
    (Recalls the memorized position according to the recall command from the seat ECU.)
    1. Outer mirror control ECU
    2. Front power seat control ECU and switch LH
    Recall control is prohibited.
    Nothing
    Nothing
    Outer mirror retraction control
    (Retracts the outer mirrors.)
    1. Outer mirror control ECU
    2. Main body ECU
    Retraction control is prohibited.
    Nothing
    Nothing
    Reverse-linked control
    (Tilts the mirrors down so that the area around the rear tires is visible when driving the vehicle in reverse.)
    1. Outer mirror control ECU
    2. Main body ECU
    Reverse-linked operation is stopped.
    Nothing
    Nothing
    Steering sensor
    (Detects the steering wheel angle.)
    1. Steering angle sensor
    2. Skid control ECU with actuator
    Periodically sends STR1S01 (STS0=1) every 12 milliseconds.
    Light turns on
    Nothing
    Auto away/return control
    (Controls the auto away/return operation according to the SKSW and IG signals. Prohibits auto away/return control.)
    1. Multiplex tilt and telescopic ECU
    2. Main body ECU, Combination meter ECU, Bus buffer ECU
    Auto away/return control does not operate.
    Nothing
    1. B2621
    2. B2624
    Memorization/recall control
    (Controls the steering wheel position memorization and recall for the seat position memory.)
    1. Multiplex tilt and telescopic ECU
    2. Front power seat control ECU and switch LH
    Memorization/recall control does not operate.
    Nothing
    B2621
    TC DTC output service
    (While TC = ON is being received from the engine, a DTC is output in response to the request from the combination meter assembly.)
    1. Combination meter ECU
    2. ECM, Center airbag sensor
    The TC service is stopped.
    Nothing
    Nothing
    Event data recorder
    (Records conditions such as the vehicle speed, the amount the accelerator is depressed, and the shift lever position when the even data recorder recording conditions are met.)
    1. Center airbag sensor
    2. ECM, Skid control ECU with actuator, Steering angle sensor
    An invalid value is stored.
    Nothing
    Nothing
    Airbag warning light control
    (Sends information used for turning the airbag warning light on and off.)
    1. Combination meter ECU
    2. Center airbag sensor
    -
    Nothing
    Nothing
    Collision detection signal
    (Notifies the system of a collision in order to perform a fuel cut at the time when a vehicle collision occurs.)
    1. ECM
    2. Center airbag sensor
    -
    Nothing
    Nothing
    Seat belt warning light control
    (Sends information used for turning the airbag warning light on and off.)
    1. Main body ECU, Combination meter ECU
    2. Center airbag sensor
    -
    Nothing
    Nothing
    Warning control
    (Displays various warnings in the combination meter according to illumination requests from various ECUs.)
    1. Combination meter ECU
    2. Main body ECU, ECM, Skid control ECU with actuator, Center airbag sensor, 4WD control ECU, Power steering ECU
    The current status is maintained until the ignition switch is turned off, or various warnings illuminate.
    Nothing
    U0100
    Buzzer control
    (Sounds various buzzers in the combination meter according to sounding requests from various ECUs.)
    1. Combination meter ECU
    2. Main body ECU, ECM, Skid control ECU with actuator, 4WD control ECU
    The buzzers do not sound.
    Nothing
    Nothing
    Meter Vehicle Speed Output 1
    (Sends vehicle speed signals, tail cancel signals and signals indicating temperature units.)
    1. Combination meter ECU
    2. -
    -
    Nothing
    Nothing
    Meter Vehicle Speed Output 2
    (Sends destination information signals, steering wheel signals, signals indicating odometer units and odometer information signals.)
    1. Combination meter ECU
    2. -
    -
    Nothing
    Nothing
    Meter Vehicle Speed Output 13
    (Sends a signal about the amount of fuel remaining in the main fuel tank and a signal about the amount of fuel remaining in the sub fuel tank.)
    1. Combination meter ECU
    2. -
    -
    Nothing
    Nothing
    Meter Vehicle Speed Output 15
    (Sends fuel sender gauge signals.)
    1. Combination meter ECU
    2. -
    -
    Nothing
    Nothing
    DTC Transmission
    Sends diagnostic signals to ECUs which transmit DTCs.
    1. Combination meter ECU
    2. -
    -
    Nothing
    Nothing
    Telltale
    (Controls indicator illumination and blinking according to CAN signals.)
    1. Combination meter ECU
    2. Main body ECU, ECM, Skid control ECU with actuator, Center airbag sensor, Power steering ECU
    Control is performed using information from the last signal or indicators are illuminated.
    Nothing
    U0129
    Speedometer
    (Controls the speedometer according to vehicle speed signals.)
    1. Combination meter ECU
    2. Skid control ECU with actuator
    The speedometer displays 0 km/h (0 mph).
    Nothing
    U0129
    ODO/TRIP meter
    (Indicates the driven distance in the combination meter according to the vehicle speed pulse signal summation value.)
    1. Combination meter ECU
    2. Skid control ECU with actuator
    The calculation stops and the last displayed value remains.
    Nothing
    U0129
    Tachometer
    (Controls the tachometer according to engine speed signals.)
    1. Combination meter ECU
    2. ECM
    The tachometer displays 0 rpm.
    Nothing
    U0100
    Engine coolant temperature gauge
    (Controls the gauge according to the engine coolant temperature signal.)
    1. Combination meter ECU
    2. ECM
    The temperature gauge needle is at the middle of the "C" mark or below.
    Nothing
    Nothing
    Oil pressure gauge
    (Performs a start operation according to the engine speed signal.)
    1. Combination meter ECU
    2. ECM
    Control is performed with the engine speed set to 0 rpm.
    Nothing
    U0100
    Transmission fluid temperature gauge
    (Controls the gauge according to the transmission fluid signals.)
    1. Combination meter ECU
    2. ECM
    The pointer needle is at the center of the "C" mark or below.
    Nothing
    Nothing
    Gear position display
    (Displays gear position according to the gear position signal and transmission temperature range signal.)
    1. Combination meter ECU
    2. ECM
    The gear position display turns off.
    SMDE=0
    Nothing
    Nothing
    Alarm control
    (Sounds various warnings.)
    1. Main body ECU
    2. ECM, Bus buffer ECU
    The warnings do not operate.
    Nothing
    1. U0199
    2. U0208
    3. U1002
    4. U1115
    Door lock control
    (Locks/unlocks the doors.)
    1. Main body ECU
    2. ECM, Combination meter ECU, Center airbag sensor, Bus buffer ECU
    The vehicle speed auto-lock control does not operate.
    Nothing
    1. U0199
    2. U0208
    3. U1002
    4. U1115
    Illumination control
    (Performs illumination control.)
    1. Main body ECU
    2. Bus buffer ECU
    KLEG is maintained.
    Nothing
    1. U0199
    2. U0208
    3. U1002
    4. U1115
    Power window control
    (Performs key off power window control.)
    1. Main body ECU
    2. Bus buffer ECU
    KLEG is maintained.
    Nothing
    1. U0199
    2. U0208
    3. U1002
    4. U1115
    Light control
    (Controls the display dimming and daytime running lights.)
    1. Main body ECU
    2. ECM, Center airbag sensor
    Daytime running light control is not performed.
    Nothing
    1. U0199
    2. U0208
    3. U1002
    4. U1115
    Wireless
    (Controls the wireless lock/unlock functions.)
    1. Main body ECU
    2. Bus buffer ECU
    KLEG is maintained.
    Nothing
    1. U0199
    2. U0208
    3. U1002
    4. U1115
    Option Control
    (Controls optional wireless lock, answer-back optional illumination, alarm warning requests and dome light warning requests.)
    1. Main body ECU
    2. Bus buffer ECU
    1. Optional wireless lock control does not operate.
    2. Answer-back control for optional illumination does not operate.
    3. Alarm warning request control does not operate.
    4. Dome light warning request control does not operate.
    Nothing
    1. U0199
    2. U0208
    3. U1002
    4. U1115
    Lock Control
    (Sends a door lock request signal.)
    1. Bus buffer ECU
    2. Main body ECU
    Lock control is not performed.
    Nothing
    Nothing
    Air conditioning control
    (Requests air conditioning control by sending DFON and ACON signals.)
    1. Bus buffer ECU
    2. -
    Air conditioning control is not performed.
    Nothing
    Nothing
    Hazard answer-back control
    (Requests hazard blinking through the HZRD bit.)
    1. Bus buffer ECU
    2. Main body ECU
    Hazard answer-back control is not performed.
    Nothing
    Nothing