Home › HEATER & AIR CONDITIONING SYSTEM › AIR CONDITIONING › AIR CONDITIONING UNIT

AIR CONDITIONING UNIT > REASSEMBLY

for Preparation Click here



1. INSTALL COOLER EXPANSION VALVE


E145026
  1. Sufficiently apply compressor oil to 4 new O-rings and the fitting surface of the hose joint.

    Compressor oil:
    ND-OIL 8 or equivalent

  1. Install the 2 O-rings to the cooler evaporator.

  1. Install the 2 O-rings to the tube and accessory.

  1. Install the cooler expansion valve and tube and accessory to the evaporator.

  1. Using a 4 mm hexagon wrench, install the 2 bolts.

    Torque:
    3.5 N*m{ 36 kgf*cm , 31 in.*lbf }



2. INSTALL NO. 1 COOLER THERMISTOR


E146390E01

NOTICE:
If reusing the evaporator, do not insert the sensor into a location where the sensor was previously inserted.

  1. Insert the sensor to a location that is 1 fin to the right or left of its previous location.

    Standard:
    Item
    Specified Condition
    a
    48 mm (1.89 in.)
    b
    9 mm (0.354 in.)
    c
    34.3 mm (1.35 in.)
    d
    47.7 mm (1.88 in.)
    e
    50 mm (1.97 in.)



3. INSTALL NO. 1 COOLER EVAPORATOR SUB-ASSEMBLY


E145024
  1. Install the evaporator to the blower case (front side).



    E145023E01
  1. Install the blower case (back side).

  1. Install the 6 screws and attach the 4 claws.



    E146153
  1. Install the packing, as shown in the illustration.



4. INSTALL HEATER RADIATOR UNIT SUB-ASSEMBLY


E145021E01
  1. Install the heater radiator unit.

  1. Attach the 3 claws to install the heater clamp.



    E146283
  1. Install the plate with the 3 screws.



5. INSTALL COOLING UNIT DAMPER SERVO SUB-ASSEMBLY (for Automatic Air Conditioning System)


E146155
  1. Install the damper servo with the 3 screws, as shown in the illustration.

  1. Connect the connector.



6. INSTALL BLOWER DAMPER SERVO SUB-ASSEMBLY


E145019
  1. Install the damper servo with the 3 screws.

  1. Connect the connector.



7. INSTALL BLOWER CASE SUB-ASSEMBLY


E145018E04
  1. Attach the 3 claws to install the case.

  1. Install the 3 screws.



8. INSTALL DAMPER SERVO SUB-ASSEMBLY


E145017
  1. Install the damper servo with the 3 screws.

  1. Connect the connector.



9. INSTALL DAMPER SERVO SUB-ASSEMBLY


E145031E01
  1. Install the servo motor.

    1. Set the plate so that the cutout part engages with the tooth of the gear, and attach the claw to install the main plate.

    2. Install the 2 screws.



    E145029E01
  1. Install the servo motor.

    1. Insert the pin into the plate groove.

    2. Attach the claw to install the main plate.

    3. Install the 2 screws.



  1. Set the damper servo so that the cutout part engages with the tooth of the gear, and attach the claw to install the damper servo.


    E145030E03



    E145016
  1. Install the 4 screws and connect the 2 connectors.



10. INSTALL AIR DUCT


E145015
  1. Install the duct with the 2 screws.



11. INSTALL BLOWER WITH FAN MOTOR SUB-ASSEMBLY


E145013
  1. Install the motor with the 3 screws.



12. INSTALL AIR CONDITIONING AMPLIFIER ASSEMBLY


E145012
  1. Install the amplifier with the 2 screws.



13. INSTALL NO. 2 AIR DUCT SUB-ASSEMBLY


E145011
  1. Install the duct with the screw.



14. INSTALL CLEAN AIR FILTER


E145010
  1. Install the filter as shown in the illustration.



15. INSTALL AIR FILTER COVER PLATE


E145008
  1. Attach the 2 clips to install the plate.



16. INSTALL NO. 3 AIR DUCT SUB-ASSEMBLY


E145006
  1. Attach the 4 claws to install the duct.



17. INSTALL LOWER DEFROSTER NOZZLE ASSEMBLY


E145005
  1. Attach the 4 claws to install the nozzle.