Home › HEATER & AIR CONDITIONING SYSTEM › AIR CONDITIONING › AIR CONDITIONING PANEL (for Column Shift Type)

AIR CONDITIONING PANEL (for Column Shift Type) > INSTALLATION

for Preparation Click here



1. INSTALL NAVIGATION RECEIVER ASSEMBLY WITH BRACKET (w/ Navigation System)


E232005
  1. Connect the connectors.

  1. Insert the navigation receiver as shown in the illustration to attach the 2 clips on its backside.

    NOTICE:
    When inserting the navigation receiver, do not press the knobs on it.



    E232001
  1. Install the navigation receiver with the 4 bolts.

    Torque:
    8.0 N*m{ 81 kgf*cm , 70 in.*lbf }



2. INSTALL RADIO RECEIVER ASSEMBLY WITH BRACKET (w/o USB Audio System)


    E161045
  1. Connect the connectors.

  1. Insert the radio receiver and attach the 3 clips on its backside.

    NOTICE:
    When inserting the radio receiver, do not press its knobs.



    B164786
  1. Install the radio receiver with the 4 bolts.



3. INSTALL RADIO RECEIVER ASSEMBLY WITH BRACKET (w/ USB Audio System)


    B230823
  1. Connect the connectors.

  1. Insert the radio receiver and attach the 3 clips on its backside.

    NOTICE:
    When inserting the radio receiver, do not press its knobs.



    B229224
  1. Install the radio receiver with the 4 bolts.



4. INSTALL INTEGRATION CONTROL AND PANEL ASSEMBLY


E146074E03
  1. Connect the connector.

  1. Attach the 4 clips to install the panel.



5. INSTALL INSTRUMENT PANEL CUP HOLDER ASSEMBLY


    B161767
  1. Attach the 4 clips to install the cup holder.

  1. Install the 4 screws.



    B163941
  1. Attach the 2 claws to install the door box.



6. INSTALL LOWER INSTRUMENT CLUSTER FINISH PANEL


    B160587
  1. Connect the connectors.

  1. Attach the 4 clips to install the finish panel.

  1. Install the 2 screws.



7. INSTALL INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY


B227982
  1. Connect the connector and attach the wire harness clamp.

  1. Attach the 12 clips to install the finish panel.



8. INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY


    B225998
  1. Connect the connector.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.

  1. Attach the 2 claws to install the DLC3.

  1. Install the 4 bolts to install the instrument panel airbag.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



9. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY LH


    B163883
  1. for Automatic Air Conditioning System:
    Attach the 2 claws to install the sensor.



    B226740
  1. Connect the connectors.

  1. Attach the 9 clips and claw to install the finish panel.

  1. Install the 2 bolts.

  1. Install the hood lock control lever.



10. INSTALL INSTRUMENT SIDE PANEL LH


    B229058
  1. Attach the 7 claws to install the side panel.



11. INSTALL CENTER LOWER INSTRUMENT COVER


  1. Install the cover with the 2 clips.


    B171284E01



12. INSTALL FRONT PILLAR GARNISH LH
  1. Attach the claw to install the front pillar garnish.

  1. Install the assist grip with the 2 bolts.



  1. Attach the 2 claws to install the 2 assist grip plugs.


    B165706



13. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH (for Double cab, CrewMax)
  1. Install the rear door opening trim weatherstrip.



14. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH (for Regular Cab)
  1. Install the front door opening trim weatherstrip.



15. INSTALL COWL SIDE TRIM BOARD LH
  1. for Regular Cab:
    Install the cowl side trim board .

  1. for Double Cab:
    Install the cowl side trim board .

  1. for CrewMax:
    Install the cowl side trim board .



16. INSTALL FRONT DOOR SCUFF PLATE LH
  1. for Regular Cab:
    Install the front door scuff plate .

  1. for Double Cab:
    Install the front door scuff plate .

  1. for CrewMax:
    Install the front door scuff plate .



17. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL


18. CHECK SRS WARNING LIGHT
  1. Check the SRS warning light (Click here).