Home › BODY › EXTERIOR › FRONT BUMPER (for Steel Type Bumper)

FRONT BUMPER (for Steel Type Bumper) > INSTALLATION

for Preparation Click here


HINT:
A bolt without a torque specification is shown in the standard bolt chart (Click here).



1. INSTALL FRONT NO. 2 BUMPER EXTENSION SUB-ASSEMBLY LH


B165508
  1. Install the bumper extension with the 4 nuts.

    Torque:
    58 N*m{ 591 kgf*cm , 43 ft.*lbf }



2. INSTALL FRONT NO. 2 BUMPER EXTENSION SUB-ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.



3. INSTALL FRONT BUMPER REINFORCEMENT


  1. Install the reinforcement with the 6 nuts.

    Torque:
    71 N*m{ 724 kgf*cm , 51 ft.*lbf }



    B165507



4. INSTALL FRONT BUMPER ARM LH


B165506
  1. Install the bumper arm with the 3 nuts.

    Torque:
    58 N*m{ 591 kgf*cm , 43 ft.*lbf }



5. INSTALL FRONT BUMPER ARM RH

HINT:
Use the same procedures described for the LH side.



6. INSTALL FRONT BUMPER END RETAINER LH


B165505
  1. Install the retainer with the 3 nuts.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



7. INSTALL FRONT BUMPER END RETAINER RH

HINT:
Use the same procedures described for the LH side.



8. INSTALL FRONT UPPER CENTER BUMPER RETAINER


  1. Install the retainer with the 6 nuts.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



    B165504



9. INSTALL FRONT BUMPER SIDE SUPPORT LH


B165503
  1. Attach the 3 claws to install the side support.

  1. Install the 2 screws.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



10. INSTALL FRONT BUMPER SIDE SUPPORT RH

HINT:
Use the same procedures described for the LH side.



11. INSTALL FRONT BUMPER BAR


  1. w/o Fog Light:
    Install the front bumper bar.

    1. w/ Intuitive Parking Assist System:
      Connect the ultrasonic sensor connectors.



    2. Install the bumper bar with the 8 bolts and 7 screws.

      Torque:
      for bolt:
      32 N*m{ 326 kgf*cm , 24 ft.*lbf }
      for labeled A:
      3.4 N*m{ 35 kgf*cm , 30 in.*lbf }
      for labeled B:
      5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



      B165501E02



  1. w/ Fog Light:
    Install the front bumper bar.

    1. w/ Intuitive Parking Assist System:
      Connect the ultrasonic sensor connectors.



    2. Install the bumper bar with the 8 bolts and 3 screws.

      Torque:
      for bolt:
      32 N*m{ 326 kgf*cm , 24 ft.*lbf }
      for screw:
      3.4 N*m{ 35 kgf*cm , 30 in.*lbf }



      B165502E03



    B165500
  1. Install 2 new clips.

    HINT:
    Use the same procedures for the RH side and LH side.



12. INSTALL FRONT LOWER BUMPER COVER


  1. Attach the 4 claws and 2 pins to install the bumper cover.


    B165499



    B165497
  1. Install the screw and clip.

    HINT:
    Use the same procedures for the RH side and LH side.



  1. Install the 16 bolts and 8 clips.


    B165498



13. INSTALL FRONT END PANEL LH


B165496
  1. Attach the 2 pins to install the panel.

  1. Install the 2 clips.



14. INSTALL FRONT END PANEL RH

HINT:
Use the same procedures described for the LH side.



15. INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH (w/ Fog Light)
  1. Connect the fog light connector.



    B166707
  1. Install the clip.



    B165877E02
  1. Install the front fender splash shield with the 2 screws, clip and 2 new clips labeled A.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



16. INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH (w/ Fog Light)

HINT:
Use the same procedures described for the LH side.



17. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL