Home › BODY › EXTERIOR › FRONT BUMPER (for Steel Type Bumper)

FRONT BUMPER (for Steel Type Bumper) > REMOVAL

for Preparation Click here



1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


3. REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH (w/ Fog Light)


B165877
  1. Remove the 3 clips, 2 screws and fender splash shield.



    B166707
  1. Remove the clip.

  1. Disconnect the fog light connector.



4. REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH (w/ Fog Light)

HINT:
Use the same procedures described for the LH side.



5. REMOVE FRONT END PANEL LH


B165496
  1. Using a clip remover, remove the 2 clips.

  1. Detach the 2 pins and remove the panel.



6. REMOVE FRONT END PANEL RH

HINT:
Use the same procedures described for the LH side.



7. REMOVE FRONT LOWER BUMPER COVER
  1. Put protective tape around the bumper cover.

  1. Using a clip remover, remove the 8 clips.



  1. Remove the 16 bolts.


    B165498E01



    B165497
  1. Remove the screw and clip.

    HINT:
    Use the same procedures for the RH side and LH side.



  1. Detach the 4 claws and 2 pins and remove the bumper cover.


    B165499



8. REMOVE FRONT BUMPER BAR


    B165500
  1. Remove the 2 clips.

    HINT:
    Use the same procedures for the RH side and LH side.



  1. w/o Fog Light:
    Remove the front bumper bar.

    1. w/o Intuitive Parking Assist System:
      Remove the 8 bolts, 7 screws and front bumper bar.



    2. w/ Intuitive Parking Assist System:
      Remove the 8 bolts and 7 screws. Then disconnect the ultrasonic sensor connectors and remove the front bumper bar.


      B165501E01



  1. w/ Fog Light:
    Remove the front bumper bar.

    1. w/o Intuitive Parking Assist System:
      Remove the 8 bolts, 3 screws and bumper bar.



    2. w/ Intuitive Parking Assist System:
      Remove the 8 bolts and 3 screws. Then disconnect the ultrasonic sensor connectors and remove the front bumper bar.


      B165502E01



9. REMOVE FRONT BUMPER SIDE SUPPORT LH


B165503
  1. Remove the 2 screws.

  1. Detach the 3 claws and remove the side support.



10. REMOVE FRONT BUMPER SIDE SUPPORT RH

HINT:
Use the same procedures described for the LH side.



11. REMOVE FRONT UPPER CENTER BUMPER RETAINER


  1. Remove the 6 nuts and retainer.


    B165504



12. REMOVE FRONT BUMPER END RETAINER LH


B165505
  1. Remove the 3 nuts and retainer.



13. REMOVE FRONT BUMPER END RETAINER RH

HINT:
Use the same procedures described for the LH side.



14. REMOVE FRONT BUMPER ARM LH


B165506
  1. Remove the 3 nuts and bumper arm.



15. REMOVE FRONT BUMPER ARM RH

HINT:
Use the same procedures described for the LH side.



16. REMOVE FRONT BUMPER REINFORCEMENT


  1. Remove the 6 nuts and reinforcement.


    B165507



17. REMOVE FRONT NO. 2 BUMPER EXTENSION SUB-ASSEMBLY LH


B165508
  1. Remove the 4 nuts and bumper extension.



18. REMOVE FRONT NO. 2 BUMPER EXTENSION SUB-ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.