Home › BODY › INTERIOR › ROOF HEADLINING (for CrewMax)

ROOF HEADLINING (for CrewMax) > REMOVAL

for Preparation Click here



1. LOWER BACK WINDOW GLASS

HINT:
Make sure to completely lower the back window glass so that the roof headlining can be removed from the rear of the vehicle.



2. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).



3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.



4. REMOVE FRONT SEAT ASSEMBLY (for Manual Seat)
  1. Remove the front seat assembly (Click here).



5. REMOVE FRONT SEAT ASSEMBLY (for Power Seat)
  1. Remove the front seat assembly (Click here).



6. REMOVE FRONT SEAT ASSEMBLY (for Center Seat)
  1. Remove the front seat assembly (Click here).



7. REMOVE REAR SEAT ASSEMBLY (for CrewMax LH Side)
  1. Remove the rear seat assembly (Click here).



8. REMOVE REAR SEAT ASSEMBLY (for CrewMax RH Side)
  1. Remove the rear seat assembly (Click here).



9. REMOVE FRONT DOOR SCUFF PLATE LH


B165841
  1. Detach the 6 claws and 3 clips, and remove the front door scuff plate.



10. REMOVE FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedures described for the LH side.



11. REMOVE REAR DOOR SCUFF PLATE LH


B169218
  1. Detach the 8 claws and 2 clips, and remove the rear door scuff plate.



12. REMOVE REAR DOOR SCUFF PLATE RH

HINT:
Use the same procedures described for the LH side.



13. REMOVE COWL SIDE TRIM BOARD LH


B165704
  1. Remove the clip.

  1. Detach the 2 clips and remove the cowl side trim board.



14. REMOVE COWL SIDE TRIM BOARD RH

HINT:
Use the same procedures described for the LH side.



15. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH
  1. Remove the front door opening trim weatherstrip.



16. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH
  1. Remove the front door opening trim weatherstrip.



17. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH
  1. Remove the rear door opening trim weatherstrip.



18. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH
  1. Remove the rear door opening trim weatherstrip.



19. REMOVE FRONT PILLAR GARNISH LH
  1. Using a screwdriver, detach the 2 claws and remove the 2 assist grip plugs.

    HINT:
    Tape the screwdriver tip before use.

  1. Remove the 2 bolts and assist grip.



  1. Detach the claw and remove the front pillar garnish.


    B165705E08



    B165709E06
  1. Protect the curtain shield airbag.

    1. Thoroughly cover the airbag with a cloth or nylon sheet and fix the ends of the cover with adhesive tape, as shown in the illustration.

      NOTICE:
      Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.



20. REMOVE FRONT PILLAR GARNISH RH

HINT:
Use the same procedures described for the LH side.



21. REMOVE LOWER CENTER PILLAR GARNISH LH


B165827
  1. Detach the 2 claws and remove the cover.



    B165828
  1. Loosen the bolt and disconnect the outer lap belt anchor.



    B165829
  1. Detach the 7 clips and 2 claws, and remove the lower center pillar garnish.



22. REMOVE LOWER CENTER PILLAR GARNISH RH

HINT:
Use the same procedures described for the LH side.



23. REMOVE CENTER PILLAR GARNISH LH
  1. Using a screwdriver, detach the 2 claws and remove the 2 assist grip plugs.

    HINT:
    Tape the screwdriver tip before use.

  1. Remove the 2 bolts and assist grip.

  1. Remove the 2 screws.

  1. Detach the claw.



  1. Pass the front seat outer belt floor anchor through the center pillar garnish, and remove the center pillar garnish.


    B165825E03



24. REMOVE CENTER PILLAR GARNISH RH

HINT:
Use the same procedures described for the LH side.



25. REMOVE FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH


B165848
  1. Detach the 6 claws of the front shoulder belt anchor plate, and slide the plate in the direction of the arrow to remove it.



26. REMOVE FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.



27. REMOVE BACK PANEL TRIM RH


B169224E05
  1. Remove the package holder net hook.

  1. Detach the 8 clips and remove the back panel trim.



28. REMOVE BACK PANEL TRIM LH
  1. Remove the package holder net hook.



  1. Detach the 8 clips and remove the back panel trim.


    B170105E05



29. REMOVE LOWER QUARTER TRIM PANEL ASSEMBLY LH


B165830
  1. Detach the 2 claws and remove the cover.



    B165831
  1. Loosen the bolt and disconnect the outer lap belt anchor.



    B169212
  1. Detach the 4 clips and remove the lower quarter trim panel.



30. REMOVE LOWER QUARTER TRIM PANEL ASSEMBLY RH


B173409
  1. Detach the 2 claws and remove the cover.



    B173410
  1. Loosen the bolt and disconnect the outer lap belt anchor.



    B173407
  1. Detach the 3 clips and remove the lower quarter trim panel.



31. REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY LH


B165711E05
  1. Using a screwdriver, detach the claw and remove the cover.

    HINT:
    Tape the screwdriver tip before use.



    B169213
  1. Remove the 2 bolts.

  1. Detach the 4 clips.

  1. Pass the rear seat outer belt floor anchor through the quarter trim panel, and remove the front quarter trim panel.



32. REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.



33. REMOVE REAR SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH


B169214
  1. Detach the 4 claws of the rear shoulder belt anchor plate, and slide the plate in the direction of the arrow to remove it.



34. REMOVE REAR SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.



35. REMOVE ROOF CONSOLE BOX ASSEMBLY
  1. for Short Type:
    Remove the roof console box .

  1. for Long Type:
    Remove the roof console box .



36. REMOVE INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)


B227021
  1. Slide the inner rear view mirror stay holder cover in the direction indicated by the arrow in the illustration to detach the 2 claws from the roof headlining, and then detach the 2 claws of the inner rear view mirror stay holder cover from the mirror and remove the inner rear view mirror stay holder cover.



37. REMOVE ROOM LIGHT ASSEMBLY


  1. w/o Rear Seat Entertainment System:

    1. Using a screwdriver, detach the 4 claws and remove the lens.

      HINT:
      Tape the screwdriver tip before use.

    2. Detach the 4 clips.



    3. Disconnect the connector and then remove the room light.


      B165836E03



    B169221
  1. w/ Rear Seat Entertainment System:

    1. Detach the 4 clips.

    2. Disconnect the connectors and then remove the room light.

      NOTICE:
      When removing the room light, be careful not to damage the shaded areas in the illustration.



38. REMOVE VISOR BRACKET COVER LH


B165714
  1. Using a moulding remover, detach the 4 claws and remove the visor bracket cover.



39. REMOVE VISOR BRACKET COVER RH

HINT:
Use the same procedures described for the LH side.



40. REMOVE VISOR ASSEMBLY LH


B165715
  1. Remove the 3 screws and visor assembly LH.



41. REMOVE VISOR ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.



42. REMOVE VISOR HOLDER


B165713

HINT:
Use the same procedure to remove the visor holder on the other side.

  1. Remove the screw and visor holder.



43. REMOVE ASSIST GRIP SUB-ASSEMBLY


B169216E03

HINT:
Use the same procedure for the other 2 assist grips.

  1. Using a screwdriver, detach the 4 claws and remove the 2 assist grip covers.

    HINT:
    Tape the screwdriver tip before use.

  1. Detach the 2 clips and remove the assist grip.



44. REMOVE ASSIST GRIP PLUG


B165716E08
  1. Insert a screwdriver into the service notch and break off the cap.

  1. Detach the clip and remove the assist grip plug.



45. REMOVE ROOF HEADLINING ASSEMBLY


B167283
  1. w/ EC Mirror:

    1. Disconnect the EC mirror connector.



    B229072
  1. Disconnect the roof wire connector and detach the 3 clamps from the front pillar.



  1. w/o Sliding Roof:



    1. Detach the 4 clips and remove the roof headlining.


      B169219E05



  1. w/ Sliding Roof:



    1. Detach the 4 clips and 14 fasteners, and remove the roof headlining.


      B229096E01



    B165845
  1. Take out the roof headlining from the cabin as shown in the illustration.

    NOTICE:
    Be careful not to damage the roof headlining when taking it out.