Home › BODY ELECTRICAL › LIGHTING › LIGHTING SYSTEM

LIGHTING SYSTEM > Headlight Signal Circuit

for Preparation Click here


DESCRIPTION

The main body ECU receives a headlight Lo switch information signal from the light control switch, and illuminates the headlight low beam.

WIRING DIAGRAM


E146027E02


INSPECTION PROCEDURE

1.PERFORM ACTIVE TEST USING TECHSTREAM (HEADLIGHT)
  1. Operate the Techstream according to the steps on the display and select "Active Test".

    Main Body ECU 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Head Light
    Headlight
    ON or OFF
    -

    OK:
    Headlight low beam turns on / turns off.



NG
Go to step 2
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

2.INSPECT FUSE (HEAD LL, HEAD RL)
  1. Remove the HEAD LL and HEAD RL fuses from the engine room junction block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    HEAD LL fuse
    Always
    Below 1 Ω
    HEAD RL fuse



NG
REPLACE FUSE
OK


3.CHECK HARNESS AND CONNECTOR (HEADLIGHT LOW BULB - BATTERY)
E146028E01
E146028E02
  1. for LH:

    1. Disconnect the A10 headlight connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      A10-2 - Body ground
      Light control switch HEAD, dimmer switch Low
      11 to 14 V
      Light control switch HEAD, dimmer switch except Low
      Below 1 V

  1. for RH:

    1. Disconnect the A11 headlight connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      A11-2 - Body ground
      Light control switch HEAD, dimmer switch Low
      11 to 14 V
      Light control switch HEAD, dimmer switch except Low
      Below 1 V



NG
Go to step 4
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (HEADLIGHT LOW BULB - BODY GROUND) 

4.INSPECT HEADLIGHT RELAY (HEAD)
A111813E06
  1. Remove the headlight relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    When battery voltage is not applied to terminals 1 and 2
    10 kΩ or higher
    When battery voltage is applied to terminals 1 and 2
    Below 1 Ω



NG
REPLACE HEADLIGHT RELAY
OK


5.CHECK HARNESS AND CONNECTOR (HEADLIGHT RELAY - BATTERY)
E147144E07
  1. Remove the headlight relay from the engine room relay block.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    Headlight relay terminal 1 - Body ground
    Always
    11 to 14 V
    Headlight relay terminal 3 - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK HARNESS AND CONNECTOR (HEADLIGHT RELAY - HEADLIGHT LOW BULB)

E147145E02

  1. Remove the headlight relay from the engine room relay block.

  1. for LH:

    1. Disconnect the A10 headlight connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      Headlight relay terminal 5 - A10-2
      Always
      Below 1 Ω
      Headlight relay terminal 5 - Body ground
      Always
      10 kΩ or higher

  1. for RH:

    1. Disconnect the A11 headlight connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      Headlight relay terminal 5 - A11-2
      Always
      Below 1 Ω
      Headlight relay terminal 5 - Body ground
      Always
      10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.CHECK HEADLIGHT (LOW BEAM)
E147118E02
  1. Disconnect the DB ECU connector.

  1. Using a service wire, connect DB-18 (HRLY) on the wire harness side and body ground.

  1. Check that the headlight low beam illuminates.

    OK:
    Headlight low beam illuminates.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (HEADLIGHT RELAY - MAIN BODY ECU)
OK

REPLACE MAIN BODY ECU