Home › BODY ELECTRICAL › LIGHTING › LIGHTING SYSTEM

LIGHTING SYSTEM > Front Fog Light Circuit

for Preparation Click here


DESCRIPTION

The main body ECU receives a front fog light switch information signal from the light control switch (front fog switch), and illuminates the front fog lights.

WIRING DIAGRAM


E146023E09


INSPECTION PROCEDURE

1.PERFORM ACTIVE TEST USING TECHSTREAM (FRONT FOG LIGHT)
  1. Operate the Techstream according to the steps on the display and select "Active Test".

    Main Body 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Front Fog Light
    Front fog light
    ON or OFF
    -

    OK:
    Front fog light turns on / turns off.



NG
Go to step 2
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

2.INSPECT FUSE (FOG)
  1. Remove the FOG fuse from the engine room junction block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    FOG fuse
    Always
    Below 1 Ω



NG
REPLACE FUSE
OK


3.CHECK HARNESS AND CONNECTOR (FRONT FOG LIGHT BULB - BATTERY)
E146024E01
E146024E02
  1. for LH:

    1. Disconnect the A30 front fog light connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      A30-2 - Body ground
      Light control switch TAIL, front fog light switch ON
      11 to 14 V
      Light control switch TAIL, front fog light switch OFF
      Below 1 V

  1. for RH:

    1. Disconnect the A31 front fog light connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      A31-2 - Body ground
      Light control switch TAIL, front fog light switch ON
      11 to 14 V
      Light control switch TAIL, front fog light switch OFF
      Below 1 V



NG
Go to step 4
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (FRONT FOG LIGHT BULB - BODY GROUND) 

4.INSPECT FOG LIGHT RELAY (FOG)
E121182E11
  1. Remove the fog light relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    When battery voltage is not applied to terminals 1 and 2
    10 kΩ or higher
    When battery voltage is applied to terminals 1 and 2
    Below 1 Ω



NG
REPLACE FOG LIGHT RELAY
OK


5.CHECK HARNESS AND CONNECTOR (FOG LIGHT RELAY - BATTERY)
E147140E07
  1. Remove the fog light relay from the engine room relay block.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    Fog light relay terminal 1 - Body ground
    Light control switch TAIL
    11 to 14 V
    Fog light relay terminal 3 - Body ground
    Always



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK HARNESS AND CONNECTOR (FR FOG RELAY - FRONT FOG LIGHT BULB)

E147141E02

  1. Remove the fog light relay from the engine room relay block.

  1. for LH:

    1. Disconnect the A30 front fog light connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      Fog light relay terminal 5 - A30-2
      Always
      Below 1 Ω
      Fog light relay terminal 5 - Body ground
      Always
      10 kΩ or higher

  1. for RH:

    1. Disconnect the A31 front fog light connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      Fog light relay terminal 5 - A31-2
      Always
      Below 1 Ω
      Fog light relay terminal 5 - Body ground
      Always
      10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.CHECK FRONT FOG LIGHT
E147119E01
  1. Disconnect the J4 ECU connector.

  1. Using a service wire, connect J4-4 (FFGO) on the wire harness side and body ground.

  1. Check that the front fog light illuminates.

    OK:
    Front fog light illuminates.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (FOG LIGHT RELAY - MAIN BODY ECU)
OK

REPLACE MAIN BODY ECU