Home › BODY ELECTRICAL › LIGHTING › LIGHTING SYSTEM

LIGHTING SYSTEM > DATA LIST / ACTIVE TEST

for Preparation Click here



DATA LIST

HINT:
Using the Techstream to read the Data List allows values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Connect the Techstream to the DLC3.

  2. Turn the ignition switch ON.

  3. Turn the Techstream on.

  4. Enter the following menus: Body Electrical / Main Body / Data List.

  5. According to the display on tester, read the "Data List".

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    D Dor Cty SW
    Front door courtesy light switch LH signal / ON or OFF
    ON: Front door courtesy light switch LH on
    OFF: Front door courtesy light switch LH off
    -
    P Dor Cty SW
    Front door courtesy light switch RH signal / ON or OFF
    ON: Front door courtesy light switch RH on
    OFF: Front door courtesy light switch RH off
    -
    RL Dor Cty SW
    Rear door courtesy light switch LH signal / ON or OFF
    ON: Rear door courtesy light switch LH on
    OFF: Rear door courtesy light switch LH off
    -
    RR Dor Cty SW
    Rear door courtesy light switch RH signal / ON or OFF
    ON: Rear door courtesy light switch RH on
    OFF: Rear door courtesy light switch RH off
    -
    Cargo Light
    Cargo light switch signal / ON or OFF
    ON: Cargo light on
    OFF: Cargo light off
    -
    Dimmer SW
    Dimmer switch signal / ON or OFF
    ON: Dimmer switch on
    OFF: Dimmer switch off
    -
    High Flasher SW
    Passing light switch signal / ON or OFF
    ON: Passing light switch on
    OFF: Passing light switch off
    -
    F Fog Light SW
    Front fog light switch signal / ON or OFF
    ON: Front fog light switch on
    OFF: Front fog light switch off
    -
    Auto Light SW
    Auto light switch signal / ON or OFF
    ON: Auto light switch on
    OFF: Auto light switch off
    -
    Head Light SW
    Headlight switch signal / ON or OFF
    ON: Headlight switch on
    OFF: Headlight switch off
    -
    Tail Light SW
    Taillight switch signal / ON or OFF
    ON: Taillight switch on
    OFF: Taillight switch off
    -
    Illumination Rate
    Illumination rate / min.: 0, max.: 99.99
    Actual illumination rate is displayed
    -


ACTIVE TEST

HINT:
Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Connect the Techstream to the DLC3.

  2. Turn the ignition switch ON.

  3. Turn the Techstream on.

  4. Enter the following menus: Body Electrical / Main Body / Active Test.

  5. According to the display on tester, perform the "Active Test".

    Main Body 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Illumi Output
    Illumination light
    ON or OFF
    -
    Tail Light
    Taillight
    ON or OFF
    -
    Head Light
    Headlight
    ON or OFF
    -
    Head Light (Hi)
    Headlight (High)
    ON or OFF
    -
    F Fog Light Rly
    Front fog light
    ON or OFF
    -
    Cargo Lgt
    Cargo light
    ON or OFF
    Cargo light switch is DOOR or on