Home › BODY › SEAT › FRONT SEAT ASSEMBLY (for Manual Seat)

FRONT SEAT ASSEMBLY (for Manual Seat) > DISASSEMBLY

for Preparation Click here


CAUTION:
Wear protective gloves. Sharp areas on the seat frame and adjuster may injure your hands.

HINT:
  1. Use the same procedures for the LH side and RH side.
  2. The procedures listed below are for the LH side.



1. REMOVE VERTICAL ADJUSTING HANDLE LH (for 8 Way Seat Type)


    B165519
  1. Using a screwdriver, detach the 2 claws and remove the vertical adjuster handle cap.

    HINT:
    Tape the screwdriver tip before use.



    B165520
  1. Remove the 2 screws and vertical adjuster handle.



2. REMOVE VERTICAL SEAT ADJUSTER KNOB LH (for 8 Way Seat Type)


    B165522
  1. Remove the snap ring and vertical seat adjuster knob.



3. REMOVE RECLINING ADJUSTER RELEASE HANDLE LH


B165521
  1. Lift the reclining adjuster release handle.

  1. Using a screwdriver, detach the claw and remove the reclining adjuster release handle.

    HINT:
    Tape the screwdriver tip before use.



4. REMOVE FRONT SEAT CUSHION SHIELD LH


    B165523E01
  1. Remove the hog rings and rubber bands of the seatback cover from the seat frame.



    B165524E01
  1. Remove the 2 screws.

  1. Detach the 3 claws in the order shown in the illustration, and then remove the cushion shield.

  1. w/ Lumbar Support Adjuster:
    Disconnect the switch connector.



5. REMOVE FRONT POWER SEAT LUMBAR SWITCH (w/ Lumbar Support Adjuster)


    B194037
  1. Remove the 2 screws and switch.



6. REMOVE INNER FRONT SEAT CUSHION SHIELD LH


B165525E01
  1. Remove the screw.

  1. Detach the 3 claws in the order shown in the illustration, and then remove the cushion shield.



7. REMOVE FRONT SEAT INNER BELT ASSEMBLY LH
  1. Driver Side:
    Disconnect the 2 connectors and detach the 4 clamps.

  1. Passenger Side:
    Disconnect the connector and detach the clamp.



    B166598
  1. Remove the nut and front seat inner belt.



8. REMOVE FRONT SEAT CUSHION COVER WITH PAD LH


    B165527
  1. Using a clip remover, remove the 2 clips.



    B165526E03
  1. Remove the hog rings.

  1. Bend the 2 seat frame claws upward.

  1. Detach the hooks and remove the seat cushion cover with pad.



9. REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER LH


B165528E01
  1. Remove the hog rings and seat cushion cover.



10. REMOVE FRONT SEAT HEADREST ASSEMBLY LH


11. REMOVE FRONT SEATBACK COVER WITH PAD LH


    B165530E01
  1. Detach the hook.



    B165531E01
  1. Remove the hog rings and seatback cover wires.



    B165533
  1. Remove the nut and seatback cover bracket from the seat frame.



    B165529
  1. Detach the 4 claws and remove the 2 headrest supports.



    B165534E01
  1. Remove the hog rings and seatback cover with pad.



12. REMOVE SEPARATE TYPE FRONT SEATBACK COVER LH


    B165532E01
  1. Remove the hog rings and seatback cover wires.



    B165535
  1. Disconnect the seatback cover bracket from the seatback pad.



    B165536E01
  1. Remove the hog rings and seatback cover from the seatback pad.



13. REMOVE RECLINING ADJUSTER INSIDE COVER LH


B165537
  1. Remove the screw and reclining adjuster inside cover.



14. REMOVE RECLINING ADJUSTER INSIDE COVER RH
  1. Remove the screw and reclining adjuster inside cover.



15. REMOVE RECLINING ADJUSTER INSIDE COVER LH


B165538
  1. Remove the screw.

  1. Detach the claw and remove the reclining adjuster inside cover.



16. REMOVE RECLINING ADJUSTER INSIDE COVER RH
  1. Remove the screw.

  1. Detach the claw and remove the reclining adjuster inside cover.



17. REMOVE LOWER FRONT SEAT CUSHION SHIELD LH


B165539
  1. Using a screwdriver, detach the claw and remove the seat cushion shield lower.

    HINT:
    Tape the screwdriver tip before use.



18. REMOVE LOWER FRONT SEAT CUSHION SHIELD RH
  1. Using a screwdriver, detach the claw and remove the seat cushion shield lower.

    HINT:
    Tape the screwdriver tip before use.



19. REMOVE LUMBAR SUPPORT ADJUSTER ASSEMBLY LH (w/ Lumbar Support Adjuster)


    B167105E04
  1. Remove the 2 springs.

  1. Detach the 6 hooks and remove the seatback spring.



    B167109
  1. Disconnect the lumbar support adjuster connector.

  1. Remove the 2 screws and lumbar support adjuster.



    B167110
  1. Detach the 3 claws and remove the bush from the seat frame.



20. REMOVE OCCUPANT CLASSIFICATION ECU (for Front Passenger Side)


B165540
  1. Disconnect the 2 ECU connectors.

  1. Using a screwdriver, detach the claw and remove the ECU.

    HINT:
    Tape the screwdriver tip before use.



21. REMOVE SEAT POSITION AIRBAG SENSOR


    B166511
  1. Using a T30 "TORX" socket wrench, remove the screw and seat position sensor with sensor protector.

  1. Disconnect the connector.

  1. Remove the seat slide position sensor protector from the seat position sensor.



22. REMOVE FRONT SEAT WIRE LH


23. REMOVE FRONT SEAT SIDE AIRBAG ASSEMBLY


    B255935
  1. Disconnect the 3 wire harness clamps from under the seat.



    B255936
  1. Disconnect the 2 clamps.

  1. Remove the 2 nuts and the front seat side airbag assembly.

    CAUTION:
    1. The nuts must not be reused.
    2. Make sure that the seat frame assembly is not deformed. If it is, replace it with a new one.