Home › BODY › SEAT › FRONT SEAT ASSEMBLY (for Power Seat)

FRONT SEAT ASSEMBLY (for Power Seat) > DISASSEMBLY

for Preparation Click here


CAUTION:
Wear protective gloves. Sharp areas on the seat frame and adjuster may injure your hands.

HINT:
  1. Use the same procedures for the LH side and RH side.
  2. The procedures listed below are for the LH side.



1. REMOVE SLIDE AND VERTICAL POWER SEAT SWITCH KNOB LH


B166941E01
  1. Apply protective tape around the cushion shield.

  1. Using a screwdriver, detach the 2 claws and remove the knob.

    HINT:
    Tape the screwdriver tip before use.



2. REMOVE RECLINING POWER SEAT SWITCH KNOB LH


B166942E01
  1. Using a screwdriver, detach the 2 claws and remove the knob.

    HINT:
    Tape the screwdriver tip before use.



3. REMOVE FRONT SEAT CUSHION SHIELD LH


    B166944E01
  1. Remove the hog rings and rubber bands of the seatback cover from the seat frame.

  1. Remove the 2 screws.



    B166945
  1. Remove the 3 screws.

  1. Detach the 2 claws and remove the cushion shield.

  1. Disconnect the switch connectors.



4. REMOVE FRONT POWER SEAT LUMBAR SWITCH LH (w/ Lumbar Support Adjuster)


B166946
  1. Remove the 2 screws and switch.



5. REMOVE LEG SUPPORT ADJUSTMENT SWITCH (w/ Leg Support Adjustment Switch)


B166947
  1. Detach the 2 wire harness clamps and remove the 2 screws and switch.

  1. Disconnect the switch connector.



6. REMOVE FRONT SEAT INNER BELT ASSEMBLY LH
  1. Driver Side:
    Disconnect the 2 connectors and detach the 4 clamps.

  1. Passenger Side:
    Disconnect the connector and detach the clamp.



    B166598
  1. Remove the nut and front seat inner belt.



7. REMOVE INNER FRONT SEAT CUSHION SHIELD LH


B166948
  1. Remove the screw.

  1. Detach the 2 claws and clip, and then remove the cushion shield.



8. REMOVE FRONT POWER SEAT SWITCH LH


B166949
  1. Disconnect the 2 connectors.

  1. w/o Seat Position Memory System:
    Disconnect the switch connector.

  1. Remove the 3 screws and switch.



9. REMOVE FRONT SEAT CUSHION COVER WITH PAD LH


    B167097
  1. Using a clip remover, remove the 2 clips.



    B227991
  1. Detach the wire harness clamp.



  1. w/ Seat Heater System or Climate Control Seat System:



      B179847
    1. Disconnect the seat heater connector and detach the 2 wire harness clamps.



    2. B179848
    3. Disconnect the seat heater control connector and detach the 2 wire harness clamps.



  1. w/ Leg Support Adjustment Switch:



      B166950E01
    1. Remove the hog rings and detach the hooks.



    2. B167096
    3. Remove the seat cushion cover wire.

    4. Remove the seat cushion cover with pad from the seat frame.



    B167115E01
  1. w/o Leg Support Adjustment Switch:

    1. Remove the hog rings.

    2. Bend the 2 seat frame claws upward.

    3. Detach the hooks and remove the seat cushion cover with pad.



10. REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER LH


  1. w/ Leg Support Adjustment Switch:
    Remove the hog rings and front seat cushion cover.


    B167100E01



    B165528E03
  1. w/o Leg Support Adjustment Switch:
    Remove the hog rings and front seat cushion cover.



11. REMOVE FRONT SEAT CUSHION HEATER ASSEMBLY LH (w/ Seat Heater System or Climate Control Seat System)


    B167117E01
  1. w/ Seat Heater System:
    Cut off the tack pins which fasten the seat heater to the seat cushion cover, and then remove the seat cushion heater from the seat cushion cover.



    B227984E01
  1. w/ Climate Control Seat System:
    Cut off the tack pins which fasten the seat heater to the seat cushion cover, and then remove the seat cushion heater from the seat cushion cover.



12. REMOVE FRONT SEATBACK COVER WITH PAD LH


    B167101E01
  1. Detach the hook.



    B167102E01
  1. Remove the hog rings and seatback cover wires.



    B165533
  1. Remove the nut and seatback cover bracket from the seat frame.



    B165529
  1. Detach the 4 claws and remove the 2 headrest supports.



    B165534E03
  1. Remove the hog rings and seatback cover with pad.



13. REMOVE SEPARATE TYPE FRONT SEATBACK COVER LH


    B167104E01
  1. Remove the hog rings and seatback cover wires.



    B165535
  1. Disconnect the seatback cover bracket from the seatback pad.



    B167103E01
  1. Remove the hog rings and seatback cover from the seatback pad.



14. REMOVE FRONT SEATBACK HEATER ASSEMBLY LH (w/ Seat Heater System or Climate Control Seat System)


    B167118E01
  1. w/ Seat Heater System:
    Cut off the tack pins which fasten the seat heater to the seatback cover, and then remove the seatback heater from the seatback cover.



    B227985E01
  1. w/ Climate Control Seat System:
    Cut off the tack pins which fasten the seat heater to the seatback cover, and then remove the seatback heater from the seatback cover.



15. REMOVE RECLINING ADJUSTER INSIDE COVER LH


B167106
  1. Remove the screw and detach the claw, and then remove the reclining adjuster inside cover.



16. REMOVE RECLINING ADJUSTER INSIDE COVER RH
  1. Remove the screw and detach the claw, and then remove the reclining adjuster inside cover.



17. REMOVE FRONT SEATBACK SHIELD LH


B167107
  1. Remove the 2 screws.

  1. Detach the claw and remove the seatback shield.



18. REMOVE FRONT SEATBACK SHIELD RH


B191027
  1. Detach the wire harness clamp.

  1. Remove the 2 screws.

  1. Detach the claw and remove the seatback shield.



19. REMOVE LOWER FRONT SEAT CUSHION SHIELD LH


B167108E01
  1. Remove the screw.

  1. Detach the hook and remove the cushion shield.



20. REMOVE LOWER FRONT SEAT CUSHION SHIELD RH
  1. Remove the screw.

  1. Detach the hook and remove the cushion shield.



21. REMOVE NO. 1 SEATBACK CLIMATE CONTROL COVER LH (w/ Climate Control Seat System)


    B232376
  1. Disconnect the connector and detach the 2 clamps.



    B232101
  1. Using a T30 "TORX" socket wrench, remove the 4 "TORX" screws and seatback climate control cover.



22. REMOVE SEATBACK CLIMATE CONTROL BLOWER LH (w/ Climate Control Seat System)


B194060
  1. Detach the clamp.

  1. Using a T30 "TORX" socket wrench, remove the 2 "TORX" screws and then remove the seatback climate control blower and seatback climate control cover.



23. REMOVE NO. 2 SEATBACK CLIMATE CONTROL COVER LH (w/ Climate Control Seat System)


    B194062
  1. Detach the 6 clamps and remove the seatback climate control cover.



24. REMOVE SEAT CUSHION CLIMATE CONTROL DUCT LH (w/ Climate Control Seat System)


B201572E01
  1. Detach the 2 clamps (A) in the direction indicated by the arrow (1).

  1. Detach the 2 clamps (B) in the direction indicated by the arrow (2).

  1. Detach the 2 claws, and remove the seat cushion climate control duct.



25. REMOVE SEAT CUSHION CLIMATE CONTROL BLOWER ASSEMBLY (w/ Climate Control Seat System)


B120540E02
  1. Disconnect the connector.

  1. Using a T30 "TORX" socket wrench, remove the "TORX" screw.

  1. Bend the bracket open slightly.

  1. Detach the 2 claws and remove the seat cushion climate control blower by pushing it rearward.



26. REMOVE LUMBAR SUPPORT ADJUSTER ASSEMBLY LH (w/ Lumbar Support Adjuster)


    B167105E01
  1. w/o Climate Control Seat System:

    1. Remove the 2 springs.

    2. Detach the 6 hooks and remove the seatback spring.



    B194042E02
  1. w/ Climate Control Seat System:

    1. Remove the 4 springs.

    2. Detach the 4 hooks and remove the seatback spring.



    B167109
  1. Disconnect the lumbar support adjuster connector.

  1. Remove the 2 screws and lumbar support adjuster.



    B167110
  1. Detach the 3 claws and remove the bush from the seat frame.



27. REMOVE SEAT HEATER CONTROL SUB-ASSEMBLY LH (w/ Seat Heater System or Climate Control Seat System)


B167111
  1. Disconnect the seat heater control connector and detach the clamp.

  1. Using a screwdriver, detach the claw and remove the seat heater control.

    HINT:
    Tape the screwdriver tip before use.



28. REMOVE OCCUPANT CLASSIFICATION ECU (for Front Passenger Side)


B167116
  1. Disconnect the 2 ECU connectors.

  1. Using a screwdriver, detach the claw and remove the ECU.

    HINT:
    Tape the screwdriver tip before use.



29. REMOVE SEAT POSITION AIRBAG SENSOR


    B166511
  1. Using a T30 "TORX" socket wrench, remove the screw and seat position sensor with sensor protector.

  1. Disconnect the connector.

  1. Remove the seat slide position sensor protector from the seat position sensor.



30. REMOVE FRONT SEAT WIRE LH


31. REMOVE FRONT SEAT SIDE AIRBAG ASSEMBLY


    B255935
  1. Disconnect the 3 wire harness clamps from under the seat.



    B255936
  1. Disconnect the 2 clamps.

  1. Remove the 2 nuts and the front seat side airbag assembly.

    CAUTION:
    1. The nuts must not be reused.
    2. Make sure that the seat frame assembly is not deformed. If it is, replace it with a new one.