Home › BODY › SEAT › FRONT SEAT ASSEMBLY (for Center Seat)

FRONT SEAT ASSEMBLY (for Center Seat) > REASSEMBLY

for Preparation Click here


CAUTION:
Wear protective gloves. Sharp areas on the center seat cushion frame and center sub-seatback support may injure your hands.



1. INSTALL CENTER FRONT SEAT BELT ASSEMBLY


B165813
  1. Attach the 2 claws to install the center front seat belt.

  1. Install the bolt and nut.

    Torque:
    for nut:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }
    for bolt:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }



2. INSTALL CENTER SEAT RECLINING ADJUSTER INSIDE COVER RH


B165594
  1. Attach the claw to install the cover.



3. INSTALL CENTER SEAT RECLINING ADJUSTER INSIDE COVER LH
  1. Attach the claw to install the cover.



4. INSTALL CENTER SEATBACK PAD


5. INSTALL CENTER FRONT SEATBACK COVER


6. INSTALL FRONT SEAT HEADREST SUPPORT


B165593
  1. Attach the 4 claws to install the 2 headrest supports.



7. INSTALL FRONT SEATBACK BOARD SUB-ASSEMBLY


    B166550
  1. RH Side:
    Connect the cable to the center seatback frame inner side.



    B166551
  1. LH Side:
    Connect the cable to the center seatback frame inner side.



    B165588
  1. Attach the 21 claws to install the board.

  1. Install the screw.



    B165587
  1. Install the 6 screws.



8. INSTALL SEAT FASTENER COVER


B165586
  1. Attach the 6 claws to install the 2 covers.



9. INSTALL CENTER FRONT SEAT ARMREST COVER


B165585
  1. Install the armrest cover with the 2 screws.



10. INSTALL FRONT SEAT TRAY


B165584
  1. Attach the 5 clips to install the tray.



11. INSTALL RECLINING REMOTE CONTROL BEZEL


B165583
  1. Attach the 2 clips and claw to install the bezel.



12. INSTALL LOWER FRONT SEAT SHOULDER BELT COVER


B165582
  1. Using a T30 "TORX" socket, install the shoulder belt cover with the 2 bolts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }



13. INSTALL UPPER REAR SEATBACK LOCK BEZEL


B165581
  1. Connect the seat belt to the shoulder belt cover.

  1. Attach the 4 claws to install the lock bezel.



14. INSTALL FRONT SEAT SHOULDER BELT COVER


B165580
  1. Using a T10 "TORX" socket, install the shoulder belt cover with the 2 screws.

    Torque:
    0.9 N*m{ 9 kgf*cm , 8 in.*lbf }



15. INSTALL FRONT SEAT HEADREST ASSEMBLY


16. INSTALL CONSOLE BOX WIRE


B165579
  1. Attach the 4 clamps to install the console box wire.



17. INSTALL CENTER POWER OUTLET SOCKET COVER


B165428E01
  1. Attach the 2 claws to install the power outlet socket cover.



18. INSTALL POWER OUTLET SOCKET ASSEMBLY


B165427E01
  1. Attach the claw to install the power outlet socket.

  1. Connect the power outlet socket connector.



19. INSTALL FRONT SEAT UNDER TRAY


    B165578
  1. Using a T30 "TORX" socket, install the under tray with the 2 bolts.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }



    B165577
  1. Connect the power outlet socket connector.



20. INSTALL FOLD SEAT STOPPER CUSHION


B165576
  1. Using a T20 "TORX" socket, install the 2 cushions with the 2 screws.

    Torque:
    2.0 N*m{ 20 kgf*cm , 18 in.*lbf }



21. INSTALL CENTER SEATBACK ASSEMBLY


    B165575
  1. Install the center seatback.

  1. RH Side:
    Using a T55 "TORX" socket, install the 2 bolts.

    Torque:
    55 N*m{ 561 kgf*cm , 41 ft.*lbf }

  1. LH Side:
    Using a T40 "TORX" socket, install the 2 bolts.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B165574
  1. Install the 2 wire harness clamps to the center seatback frame.



22. CONNECT CENTER FRONT SEAT BELT ASSEMBLY RH


B165812
  1. Connect the seat belt with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



23. INSTALL CENTER FRONT SEAT INNER BELT ASSEMBLY


B165811E01
  1. Install the inner belt with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not overlap the anchor part of the seat belt and protruding part of the center seat cushion frame.



24. INSTALL CENTER FRONT SEAT CUSHION PAD


B165573E02
  1. Using hog ring pliers, install the seat cushion pad to the seat cushion frame with new hog rings.



25. INSTALL CENTER FRONT SEAT CUSHION COVER


    B165572E02
  1. Install the seat cushion cover, and then attach the 3 hooks.



26. INSTALL REAR SEAT LOCK LATCH


B165571
  1. Install the seat lock latch and fasten the button.



    B165570
  1. Using a T30 "TORX" socket, install the 2 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



27. INSTALL CENTER FRONT SEAT CUSHION ASSEMBLY


B165569
  1. Install the seat cushion with the 2 bolts.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }



28. INSTALL CENTER SEAT CUSHION SHIELD RH


B165568
  1. Attach the 7 claws and 3 clips to install the cushion shield.

  1. Using a T30 "TORX" socket, install the bolt.

    Torque:
    2.0 N*m{ 20 kgf*cm , 18 in.*lbf }



29. INSTALL CENTER SEAT CUSHION SHIELD LH


B165567
  1. Attach the 7 claws and 2 clips to install the cushion shield.

  1. Using a T30 "TORX" socket, install the bolt.

    Torque:
    2.0 N*m{ 20 kgf*cm , 18 in.*lbf }



30. INSTALL VIDEO TERMINAL (for CrewMax)


    B171153
  1. Attach the 4 claws to install the video terminal.



    B169732
  1. Attach the clamp to the back panel.



31. INSTALL REAR POWER POINT SOCKET (for AC Power Supply)


    B170306
  1. Attach the 2 claws to install the power outlet socket.



32. INSTALL REAR POWER OUTLET SOCKET COVER (for Standard)


    B170304
  1. Attach the 2 claws to install the power outlet socket cover.



33. INSTALL REAR POWER OUTLET SOCKET (for Standard)


    B170303
  1. Attach the claw to install the power outlet socket.



34. INSTALL NO. 2 SEATBACK LOCK CONTROL BEZEL (for CrewMax)


B171170E02
  1. for AC Power Supply:

    1. Connect the clamp.

  1. Install the bezel with the 4 screws.



35. INSTALL NO. 1 CONSOLE BOX REGISTER ASSEMBLY (for CrewMax)


B174164
  1. Install the register with the 3 screws.



36. INSTALL NO. 2 CONSOLE BOX REGISTER ASSEMBLY (for CrewMax)


B169094
  1. Install the register with the 3 screws.



37. INSTALL REAR POWER OUTLET SOCKET COVER (for Double Cab)


B165426E01
  1. Attach the 2 claws to install the power outlet socket cover.



38. INSTALL REAR POWER OUTLET SOCKET ASSEMBLY (for Double Cab)


B165425E01
  1. Attach the claw to install the power outlet socket.



39. INSTALL CENTER SEATBACK PANEL


B165566
  1. Attach the 4 claws and 4 clips to install the center seatback panel.



    B166347
  1. for Double Cab:

    1. Connect the power outlet socket connector.

    2. Attach the 4 clips to install the center seatback panel.

    3. Install the 2 screws.



    B169093
  1. for CrewMax:

    1. Connect the 2 connectors.

    2. Attach the 4 claws and 4 clips to install the center seatback panel.