Home › BODY › SEAT › SEAT HEATER SWITCH (w/ Seat Heater System or Climate Control Seat System)

SEAT HEATER SWITCH (w/ Seat Heater System or Climate Control Seat System) > INSPECTION

for Preparation Click here



1. INSPECT SEAT HEATER SWITCH LH (w/ Seat Heater System)


B165795E05
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    3 (SW) - 7 (RV)
    Switch OFF
    2.7 to 4.1 kΩ
    Switch ON (Min.)
    Switch ON (Max.)
    0.28 to 0.42 kΩ

    HINT:
    As the dial is being turned, the resistance changes gradually.

    If the result is not as specified, replace the switch.

  1. Apply battery voltage to the switch connector, and check that the seat heater switch illuminates.

    OK:
    Measurement Condition
    Specified Condition
    Battery positive (+) → 8 (ILL+)
    Battery negative (-) → 2 (ILL-)
    Illuminates

    If the result is not as specified, replace the switch.

  1. Apply battery voltage to the switch connector, and check that the seat heater switch illuminates.

    OK:
    Measurement Condition
    Switch Condition
    Specified Condition
    Battery positive (+) → 9 (IG)
    Battery negative (-) → 4 (E)
    Switch on
    Indicator illuminates

    If the result is not as specified, replace the switch.



2. INSPECT SEAT HEATER SWITCH RH (w/ Seat Heater System)


B165796E05
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    2 (SW) - 5 (RV)
    Switch OFF
    2.7 to 4.1 kΩ
    Switch ON (Min.)
    Switch ON (Max.)
    0.28 to 0.42 kΩ

    HINT:
    As the dial is being turned, the resistance changes gradually.

    If the result is not as specified, replace the switch.

  1. Apply battery voltage to the switch connector, and check that the seat heater switch illuminates.

    OK:
    Measurement Condition
    Specified Condition
    Battery positive (+) → 6 (ILL+)
    Battery negative (-) → 1 (ILL-)
    Illuminates

    If the result is not as specified, replace the switch.

  1. Apply battery voltage to the switch connector, and check that the seat heater switch illuminates.

    OK:
    Measurement Condition
    Switch Condition
    Specified Condition
    Battery positive (+) → 7 (IG)
    Battery negative (-) → 3 (E)
    Switch on
    Indicator illuminates

    If the result is not as specified, replace the switch.



3. INSPECT SEAT HEATER SWITCH LH (w/ Climate Control Seat System)



B194049E03

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (for Heater):
    Tester Connection
    Switch Condition
    Specified Condition
    2 (SW) - 6 (RV)
    Switch off
    2.2 to 4.0 kΩ
    Switch on (Min.)
    Switch on (Max.)
    0.3 to 0.5 kΩ

    Standard Resistance (for Blower):
    Tester Connection
    Switch Condition
    Specified Condition
    5 (BLLH) - 4 (SW-)
    Switch off
    1.54 to 2.86 kΩ
    Switch on (Min.)
    Switch on (Max.)
    Below 0.1 kΩ

    HINT:
    As the dial is being turned, the resistance changes gradually.

    If the result is not as specified, replace the switch.

  1. Apply battery voltage to the switch connector, and check that the seat heater switch illuminates.

    OK:
    Measurement Condition
    Condition
    Specified Condition
    Battery positive (+) → 7 (ILL+)
    Battery negative (-) → 1 (ILL-)
    Always
    Pointer and level
    illuminates

    If the result is not as specified, replace the switch.

  1. Apply battery voltage to the switch connector, and check that the seat heater switch illuminates.

    OK:
    Measurement Condition
    Switch Condition
    Specified Condition
    Battery positive (+) → 8 (IG)
    Battery negative (-) → 3 (E)
    Switch on
    Indicator
    illuminates

    If the result is not as specified, replace the switch.



4. INSPECT SEAT HEATER SWITCH RH (w/ Climate Control Seat System)



B194050E02

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (for Heater):
    Tester Connection
    Switch Condition
    Specified Condition
    4 (SW) - 10 (RV)
    Switch off
    2.2 to 4.0 kΩ
    Switch on (Min.)
    Switch on (Max.)
    0.3 to 0.5 kΩ

    Standard Resistance (for Blower):
    Tester Connection
    Switch Condition
    Specified Condition
    7 (BLRH) - 6 (SVSG)
    Switch off
    1.54 to 2.86 kΩ
    Switch on (Min.)
    Switch on (Max.)
    Below 0.1 kΩ

    HINT:
    As the dial is being turned, the resistance changes gradually.

    If the result is not as specified, replace the switch.

  1. Apply battery voltage to the switch connector, and check that the seat heater switch illuminates.

    OK:
    Measurement Condition
    Condition
    Specified Condition
    Battery positive (+) → 11 (ILL+)
    Battery negative (-) → 5 (ILL-)
    Always
    Pointer and level
    illuminates

    If the result is not as specified, replace the switch.

  1. Apply battery voltage to the switch connector, and check that the seat heater switch illuminates.

    OK:
    Measurement Condition
    Switch Condition
    Specified Condition
    Battery positive (+) → 12 (IG)
    Battery negative (-) → 3 (E)
    Switch on
    Indicator
    illuminates

    If the result is not as specified, replace the switch.