Home › TRANSMISSION ยท A750E AUTOMATIC TRANSMISSION › SHIFT LEVER ASSEMBLY (for Column Shift Type)

SHIFT LEVER ASSEMBLY (for Column Shift Type) > REASSEMBLY

for Preparation Click here



1. INSTALL TRANSMISSION CONTROL SWITCH (P POSITION)


C155899
  1. Install the switch with the 2 screws to the column shift control shift lever retainer.



2. INSTALL TRANSMISSION CONTROL SWITCH (S POSITION)


C155898E01
  1. Apply MP grease to the switch shown in the illustration.

  1. Install the switch with the 2 screws to the column shift control shift lever retainer.



    C157300E04
  1. Securely connect the 2 wire terminals to terminal 6 and 13 of the transmission control switch connector.



3. CONNECT NO. 1 SHIFT LOCK PLATE SUB-ASSEMBLY


C158360
  1. Using a hammer, tap in the spring pin to connect the shift lock plate and shift lock solenoid.



4. INSTALL SHIFT LOCK SOLENOID


C155894
  1. Install the shift lock solenoid with No. 1 shift lock plate sub-assembly, 2 bushes and collar to the column shift control shift lever retainer with the screw.

    Torque:
    1.2 N*m{ 12 kgf*cm , 11 in.*lbf }



    C158361E01
  1. Attach the 2 claws to install the shift lock solenoid bracket.



    C157300E05
  1. Securely connect the 2 wire terminals to terminal 1 and 8 of the transmission control switch connector.



5. INSTALL COLUMN SHIFT SHIFT LEVER SUB-ASSEMBLY


C155892E01
  1. Apply MP grease to the 2 lever selecting bushes shown in the illustration.

  1. Install the 2 lever selecting bushes and shift lever to the column shift control shift lever retainer.

  1. Pass the wire harness of the shift lever through the control shaft tube clamp.



    C155897
  1. Attach the control shaft tube clamp to the column shift control shift lever retainer.



    C157300E06
  1. Securely connect the 3 wire terminals to terminal 4 (SFTD), 5 (SFTU) and 11 (E) of the transmission control switch connector. Then push the connector housing retainer to lock it.

  1. Fix the connector housing retainer of the connector in place.



6. INSTALL COLUMN SHIFT SHIFT LOCK RELEASE LINK


C155891
  1. Install the spring and shift lock release link to the shift lever plate.



7. INSTALL SHIFT LEVER PLATE SUB-ASSEMBLY


C157032
  1. Install the shift lever plate to the column shift control shift lever retainer with the 3 bolts.

    Torque:
    2.3 N*m{ 23 kgf*cm , 20 in.*lbf }



    C155893
  1. Clamp the harness with the 4 wire guides and wire harness clamp as shown in the illustration.



8. INSTALL COLUMN SHIFT LEVER COMPRESSION SPRING


C155888E01
  1. Apply MP grease to the spring shown in the illustration.

  1. Temporarily install the spring with the bolt to the column shift control shift lever retainer.



    C157302E01
  1. With the shift lever's protrusion pushed towards the column shift control shift lever retainer's N position wall, align the spring's roller to the groove as shown in the illustration. Then tighten the bolt.

    Torque:
    3.8 N*m{ 38 kgf*cm , 33 in.*lbf }



9. INSTALL COLUMN SHIFT SHIFTING BELLCRANK ASSEMBLY


C159647E01
  1. Apply MP grease to the shifting bellcrank shown in the illustration.

  1. Install the shifting bellcrank with the bolt.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }