Part tightened
| N*m
| kgf*cm
| ft.*lbf
|
No. 2 water by-pass pipe x Timing chain cover, Front water by-pass joint, Oil filter bracket
| 10
| 102
| 7
|
Front stabilizer bracket x Body
| 69
| 704
| 51
|
Engine hunger x Cylinder head
| 43
| 438
| 32
|
Engine mounting insulator x Body
| 79
| 806
| 58
|
No. 1 water by-pass pipe x Cylinder head cover
| 18
| 184
| 13
|
Drive plater and ring gear x Crankshaft
| 1st
| 30
| 301
| 22
|
2nd
| Turn 90°
| Turn 90°
| Turn 90°
|
Engine wire x Engine room junction block
| 10
| 102
| 7
|
Ground wire x Air injection control driver bracket
| 8.0
| 82
| 71 in.*lbf
|
Engine wire x positive (+) battery cable
| 13
| 133
| 10
|
Ground wire x Oil filter bracket
| 8.0
| 82
| 71 in.*lbf
|
Air pump connector bracket x Body
| 6.0
| 61
| 53 in.*lbf
|
Air cleaner case x Body
| 5.0
| 51
| 44 in.*lbf
|
Hose clamp x Air cleaner hose
| 4.0
| 41
| 35 in.*lbf
|
Engine hood x Hinge
| 13
| 133
| 10
|
Timing chain cover stud bolt
| 20
| 204
| 15
|
Cylinder head cover spacer x Cylinder head cover
| 10
| 102
| 7
|
No. 1 tube x Intake manifold
| 8.2
| 83
| 73 in.*lbf
|
Front No. 1 engine mounting bracket RH x Cylinder block
| 35
| 357
| 26
|
Front No. 1 engine mounting bracket LH x Cylinder block
| 35
| 357
| 26
|
No. 1 chain tensioner x Cylinder head
| 10
| 102
| 7
|
No. 2 chain tensioner x Cylinder head
| 10
| 102
| 7
|
No. 3 chain tensioner x Cylinder head
| 10
| 102
| 7
|
No. 1 chain vibration damper x Cylinder block
| 21
| 214
| 15
|
Camshaft timing gear x Camshaft
| 100
| 1020
| 74
|
Camshaft timing exhaust gear x Camshaft
| 100
| 1020
| 74
|
Camshaft housing x Cylinder head
| for Bolt A
| 10
| 102
| 7
|
for Except bolt
| 30
| 306
| 22
|
Camshaft bearing cap x Camshaft housing
| 16
| 163
| 12
|
Cylinder head x Cylinder block
| 1st
| 36
| 367
| 27
|
2nd
| Turn 90°
| Turn 90°
| Turn 90°
|
3rd
| Turn 90°
| Turn 90°
| Turn 90°
|
for 12 mm head
| 21
| 214
| 15
|
Cylinder head stud bolt
| E7 and E8 "TORX"
| 9.0
| 92
| 80 in.*lbf
|
No. 2 straight screw plug x Cylinder head
| 85
| 867
| 63
|
No. 1 straight screw plug x Cylinder head
| 44
| 449
| 32
|
Connecting rod x Connecting rod cap
| 1st
| 40
| 408
| 30
|
2nd
| Turn 90°
| Turn 90°
| Turn 90°
|
Crankshaft bearing cap x Cylinder block
| for Inside position
| 61
| 622
| 45
|
for Outside position
| 27
| 275
| 20
|
2nd
| Turn 90°
| Turn 90°
| Turn 90°
|
for Cylinder block side position
| 45
| 459
| 33
|
Cylinder block stud bolt
| for Stud bolt A (E8 "TORX")
| 20
| 204
| 15
|
for Stud bolt B (E8 "TORX")
| 9.0
| 92
| 80 in.*lbf
|
No. 1 oil nozzle x Cylinder block
| 10
| 102
| 7
|
Oil pan stud bolt (E6 and E7 "TORX")
| for stud bolt A
| 5.0
| 51
| 44 in.*lbf
|
for stud bolt B
| 9.0
| 92
| 80 in.*lbf
|
Oil drain pipe x Cylinder block
| 10
| 102
| 7
|
Oil seal retainer x Cylinder block
| 10
| 102
| 7
|
Oil strainer x Oil pan
| 10
| 102
| 7
|
Oil pan baffle plate x Oil pan
| 10
| 102
| 7
|
Oil pan x cylinder block
| for Bolt A
| 10
| 122
| 7
|
for Bolt B
| 35
| 357
| 26
|
for Nut
| 35
| 357
| 26
|
No. 2 oil pan x Oil pan
| 10
| 102
| 7
|
No. 1 heat exchanger cover x Cylinder block
| 21
| 214
| 15
|
Cylinder block water drain cock x Cylinder block
| 30
| 306
| 22
|
Water drain cock plug x Water drain cock
| 13
| 133
| 10
|
Camshaft timing oil control valve x Cylinder head cover
| 10
| 102
| 7
|
Crankshaft position sensor x Oil pan
| 10
| 102
| 7
|
Camshaft position sensor x Cylinder head cover
| 10
| 102
| 7
|
VVT sensor x Cylinder head cover
| 10
| 102
| 7
|
Oil filler cap housing x Cylinder head cover
| 10
| 102
| 7
|
Front engine mounting insulator x Front No. 1 engine mounting bracket
| 72
| 734
| 53
|
Rear No. 1 engine mounting insulator x Transmission
| for 2WD
| 40
| 408
| 30
|
for 4WD
| 59
| 602
| 44
|
No, 3 frame crossmember x frame
| 110
| 1122
| 81
|
No. 3 frame crossmember x Rear No. 1 engine mounting insulator
| 21
| 214
| 15
|