Home › ENGINE ยท 3UR-FBE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P060B    Internal Control Module A/D Processing Performance

for Preparation Click here


DESCRIPTION

This DTC is output when a communication error occurs in the ECM.

DTC No.
DTC Detection Condition
Trouble Area
P060B
ECM main CPU communication error
ECM

MONITOR STRATEGY


Related DTCs
None
Required Sensors/Components (Main)
ECM
Required Sensors/Components (Related)
-
Frequency of Operation
Once per driving cycle
Duration
16 seconds
MIL Operation
Immediate
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Case 1 and 4 
Monitor runs whenever following DTCs not present
None
Both of the following conditions are met
-
Battery voltage
8V or more
Starter
OFF

Case 2 and 3 
Monitor runs whenever following DTCs not present
None

TYPICAL MALFUNCTION THRESHOLDS


Case 1 
Internal control module serial communication
Fail

Case 2 
AD converter
Fail

Case 3 
Knock sensor circuit
Fail

Case 4 
Knock sensor serial communication
Fail

CONFIRMATION DRIVING PATTERN


A199238E02

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the Techstream on [A].
  6. Wait 16 seconds or more.
  7. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [B].
  8. Read the pending DTC.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  9. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  10. Input the DTC: P060B.
  11. Check the DTC judgment result.

    Tester Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    If the judgment result shows ABNORMAL, the system has a malfunction.

  12. If the test result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


INSPECTION PROCEDURE

1.CHECK DTC
  1. Clear DTC (Click here).

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal and wait for 1 minute.

  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch to ON.

  1. Wait 16 seconds or more.

  1. Check DTC.

    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC P060B is output
    B
    DTC P060B and P0327, P0328, P032C, P032D, P0332, P0333, P033C, P033D are output
    C



B
REPLACE ECM (Click here)

C
GO TO DTC (P0327, P0328, P032C, P032D, P0332, P0333, P033C, P033D) (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (Click here)