Home › BODY ELECTRICAL › METER › METER / GAUGE SYSTEM

METER / GAUGE SYSTEM > OPERATION CHECK

for Preparation Click here



INSPECT INDICATOR/WARNING LIGHT
  1. Check the following indicators and warning lights.
    Indicator/Warning light
    Switch Condition
    Specified Condition
    ABS warning light
    Ignition switch OFF→ ON
    Comes on for 3 seconds
    SLIP indicator light
    EPS warning light*
    SRS warning light
    Ignition switch OFF→ ON
    Comes on for 6 seconds
    CHARGE warning light
    Ignition switch OFF→ ON
    Illuminates when ignition switch is turned ON. Turns off when engine is started.
    MIL

    1. *: for 1UR-FE


INSPECT SPEEDOMETER
  1. Connect the Techstream to the DLC3 connector.

  2. Turn the ignition switch ON.

  3. Turn the Techstream on.

  4. Enter the following menus: Powertrain / Engine and ECT / Data List.

  5. According to the display on Techstream, read the "Data List".

    Reference:
    for mph:
    Techstream Display
    Speedometer Display
    20 mph
    19 to 22 mph
    40 mph
    39 to 42.5 mph
    60 mph
    59.5 to 63.5 mph
    80 mph
    79.5 to 84 mph
    100 mph
    100 to 105 mph
    120 mph
    120 to 125.5 mph
    for km/h:
    Techstream Display
    Speedometer Display
    20 km/h
    21 to 25 km/h
    40 km/h
    41.7 to 46.2 km/h
    60 km/h
    62.7 to 67.2 km/h
    80 km/h
    83.4 to 88.4 km/h
    100 km/h
    104.3 to 109.3 km/h
    120 km/h
    125.1 to 130.6 km/h
    140 km/h
    145.8 to 151.8 km/h
    160 km/h
    166.2 to 173.2 km/h
    180 km/h
    186.9 to 194.5 km/h
    200 km/h
    207.7 to 215.7 km/h

    NOTICE:
    Do not use worn, underinflated or overinflated tires, as the speedometer reading will be inaccurate.

  6. Check the deflection width of the speedometer indicator.

    Reference:
    0.5 km/h (0.3 mph)


INSPECT TACHOMETER (w/ Tachometer)
  1. Connect a tune-up tachometer, and start the engine.

  2. Compare the test results with the tachometer indicator.

    DC 13.5 V, at 25°C (77°F):
    Standard indication (rpm)
    Acceptable range
    Data in ( ) is for reference
    700
    630 to 770
    1000
    (900 to 1100)
    2000
    (1850 to 2150)
    3000
    2800 to 3200
    4000
    (3800 to 4200)
    5000
    4800 to 5200
    6000
    (5750 to 6250)
    7000
    6700 to 7300

    If the result is not as specified, the speedometer may have a malfunction.


INSPECT METER/GAUGE
  1. Connect the Techstream to the DLC3.

  2. Perform "Active Test" (Click here).

    OK:
    Each meter/gauge's needle indication is normal.


INSPECT WARNING/INDICATOR LIGHT
  1. Connect the Techstream to the DLC3.

  2. Perform "Active Test" (Click here).

    OK:
    Each warning/indicator light turns ON and OFF using Techstream.


INSPECT MULTI-INFORMATION DISPLAY (w/ Multi-information Display)
  1. Connect the Techstream to the DLC3.

  2. Perform "Active Test" (Click here).

    HINT:
    If this Active Test is being performed and the ignition switch is turned OFF and then ON, the A/T and ODO/TRIP display area's background may turn white. If this occurs, end this Active Test and turn the ignition switch OFF.

    OK:
    All dots in the multi-information display turn ON and OFF using Techstream.