SEAT BELT WARNING SYSTEM > TERMINALS OF ECU |
| CHECK COMBINATION METER (METER ECU) |

Measure the resistance and voltage according to the value(s) in the table below.
| Terminal No. (Symbols) | Wiring Color | Terminal Description | Condition | Specified Condition |
| J28-18 (B) - Body ground | LG - Body ground | Power source | Always | 11 to 14 V |
| J28-15 (P/SB) - Body ground | L - Body ground | Front passenger side seat belt warning light signal | Front passenger side seat is occupied, seat belt is fastened | Below 1 V |
| Front passenger side seat is occupied, seat belt is unfastened | Alternating between 11 to 14 V and below 1 V | |||
| J28-31 (TX+) - Body ground | Y - Body ground | Accessory meter input signal | Ignition switch ON | Local communication signal |
| J28-33 (CANH) - J28-34 (CANL) | SB - W | Driver side seat belt warning light signal (CAN signal) | Ignition switch OFF | 108 to 132 Ω |
| J28-33 (CANH) - J28-40 (E1) | SB - W-B | Driver side seat belt warning light signal (CAN signal) | Ignition switch OFF | 200 Ω or higher |
| J28-34 (CANL) - J28-40 (E1) | W - W-B | Driver side seat belt warning light signal (CAN signal) | Ignition switch OFF | 200 Ω or higher |
| J28-40 (E1) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| CHECK INTEGRATION CONTROL AND PANEL |

Measure the voltage according to the value(s) in the table below.
| Terminal No. (Symbols) | Wiring Color | Terminal Description | Condition | Specified Condition |
| J37-16 (IG+) - Body ground | P - Body ground | Power source | Always | 11 to 14 V |
| J37-14 (PBEW) - Body ground | L - Body ground | Front passenger side seat belt warning light signal | Front passenger side seat is occupied, seat belt is fastened | Below 1 V |
| Front passenger side seat is occupied, seat belt is unfastened | Alternating between 11 to 14 V and below 1 V |
| CENTER AIRBAG SENSOR |

| Terminal No. | Terminal Symbol | Destination |
| Q1-13 | FSP- | Occupant classification ECU |
| Q1-12 | FSP+ | Occupant classification ECU |
| P1-11 | DBE+ | Front seat inner belt LH (Seat belt buckle switch LH) |
| P1-12 | DBE- | Front seat inner belt LH (Seat belt buckle switch LH) |
| CHECK OCCUPANT CLASSIFICATION ECU |

Measure the voltage and resistance according to the value(s) in the table below.
| Terminal No. (Symbols) | Wiring Color | Terminal Description | Condition | Specified Condition |
| Y2-1 (+B) - Body ground | G - Body ground | Power source | Always | 11 to 14 V |
| Y2-7 (IG) - Body ground | LG - Body ground | Occupant classification ECU +B line | Ignition switch ON | 11 to 14 V |
| Y2-4 (FSR-) - Y2-8 (FSR+) | B - W | Pressure sensor signal line | Ignition switch ON | Below 1 to 5 V |
| Y2-9 (BSW) - Y2-5 (BGND) | L - BE | Passenger side buckle switch line | Ignition switch ON | Pulse generation |
| Y2-3 (GND) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| Terminal No. (Symbols) | Wiring Color | Terminal Description | Condition | Specified Condition |
| Q11-1 (+B) - Body ground | R - Body ground | Power source | Always | 11 to 14 V |
| Q11-7 (IG) - Body ground | SB - Body ground | Occupant classification ECU +B line | Ignition switch ON | 11 to 14 V |
| Q11-4 (FSR-) - Q11-8 (FSR+) | B - W | Pressure sensor signal line | Ignition switch ON | Below 1 to 5 V |
| Q11-9 (BSW) - Q11-5 (BGND) | L - BE | Passenger side buckle switch line | Ignition switch ON | Pulse generation |
| Q11-3 (GND) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |