Home › BODY › ENGINE HOOD / DOOR › FRONT DOOR (for Double Cab)

FRONT DOOR (for Double Cab) > REASSEMBLY

for Preparation Click here


HINT:
  1. Use the same procedures for the RH side and LH side.
  2. The procedures listed below are for the LH side.
  3. A bolt without a torque specification is shown in the standard bolt chart (Click here).



1. INSTALL FRONT DOOR WEATHERSTRIP LH


    B166219
  1. Attach the 38 clips to install the weatherstrip.

    HINT:
    If clips are damaged during installation, replace them.



2. INSTALL FRONT DOOR CHECK ASSEMBLY LH


    B165675
  1. Apply MP grease to the sliding areas of the door check.

  1. Install the door check to the door panel with the 2 nuts.

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }

  1. Apply adhesive to the threads of the bolt.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

  1. Install the bolt.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }



3. INSTALL FRONT DOOR PANEL PROTECTOR LH


    B166214
  1. Attach the 8 clips to install the door panel protector.



4. INSTALL FRONT NO. 2 DOOR STIFFENER CUSHION


    B165680
  1. Install the stiffener cushion with the 2 clips.



5. INSTALL FRONT DOOR LOCK OPEN ROD LH
  1. Install the lock open rod to the outside handle frame.



6. INSTALL FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY LH


    B165673
  1. Slide the outside handle frame to install it.

    NOTICE:
    If the release plate is not pulled and held when installing the outside handle, it will strike against the outside handle and become damaged.

  1. Using a T30 "TORX" wrench, tighten the screw.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }

  1. Install the front and rear outside handle pads.



7. INSTALL FRONT DOOR HANDLE ASSEMBLY OUTSIDE LH


    B165681
  1. Install the handle by pushing it in the direction of the arrow in the illustration.

    NOTICE:
    If the bellcrank lever is not pulled and held when installing the handle, the bellcrank lever will interfere with the handle and become damaged.



8. INSTALL FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY LH


    B165672E01
  1. Install the front door inside locking cable.



    B266907
  1. Attach the 3 claws.



9. INSTALL FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH


    B165670E01
  1. Install the front door lock remote control cable.



10. INSTALL FRONT DOOR LOCK ASSEMBLY LH
  1. Apply MP grease to the sliding and rotating areas of the door lock.

  1. Install a new door lock wire harness packing to the door lock.

    NOTICE:
    1. When reusing a door lock that has been removed, replace the packing in the connecting part with new packing.
    2. Be careful that no grease or dirt sticks to the packing surface in the connecting part.
    3. Reusing removed packing or using damaged packing will allow water to penetrate through to the connecting part, resulting in a malfunction of the door lock.



    B165669
  1. Using a T30 ''TORX'' wrench, install the door lock with the 3 screws.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Connect the door lock connector.



11. INSTALL FRONT DOOR OUTSIDE HANDLE COVER LH


    B165665E01
  1. Using a T30 ''TORX'' socket, install the cover (with the door key cylinder) with the screw.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }

  1. Install the hole plug.



12. INSTALL FRONT DOOR FRONT LOWER FRAME SUB-ASSEMBLY LH


    B165663
  1. Install the frame with the 2 bolts.



13. INSTALL FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY LH


    B165682
  1. Install the frame with the 2 bolts.



14. INSTALL FRONT DOOR GLASS RUN LH


    B165689
  1. Install the front door glass run.



15. INSTALL FRONT OUTER DOOR GLASS WEATHERSTRIP ASSEMBLY LH


B165858
  1. Attach the claw to install the weatherstrip.



16. INSTALL SIDE AIRBAG SENSOR ASSEMBLY LH


    B166953
  1. Install the side airbag sensor with the bolt.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

  1. Connect the connector.



17. INSTALL FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH


    B165662
  1. Apply MP grease to the sliding and rotating areas of the regulator motor.

  1. Using a T25 ''TORX'' driver, install the motor with the 3 screws.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

    HINT:
    For a new front window regulator, the installation position of the regulator will be set when the self-tapping screws are installed.



18. INSTALL FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY LH


    B166218E01
  1. Apply MP grease to the sliding and rotating areas of the window regulator.

    NOTICE:
    Do not apply grease to the spring of the window regulator.

  1. Loosely install the temporary bolt onto the window regulator.

  1. Insert the window regulator into the door panel. Use the temporary bolt to hang the window regulator on the door panel.

  1. Temporarily install the window regulator with the 5 bolts, and tighten the temporary bolt so that it contacts the door panel.

  1. Tighten the 6 bolts in the order shown in the illustration.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Connect the connector.



19. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY LH


    B166217E01
  1. Insert the door glass into the door panel along the glass run as indicated by the arrows in the illustration.

    NOTICE:
    Be careful not to damage the glass.



    B166216
  1. Install the door glass to the window regulator with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



20. INSTALL FRONT DOOR SERVICE HOLE COVER LH
  1. Install the front door service hole cover to the door panel.

    NOTICE:
    1. When installing the service hole cover, pull out the links through the service hole cover.
    2. There should be no wrinkles or folds after attaching the service hole cover.
    3. After attaching the service hole cover, check the sealing quality.

  1. Connect the connector.



21. INSTALL FRONT NO. 1 DOOR TRIM BRACKET


    B165656
  1. Install the bracket with the 2 screws.



22. INSTALL FRONT NO. 1 SPEAKER ASSEMBLY


B166269E01
  1. Temporarily install the speaker by attaching the claws of the speaker to the door panel.

  1. Install the speaker with the 4 screws.

    NOTICE:
    Do not touch the cone part of the speaker.

    HINT:
    Install the screws in the order shown in the illustration.

  1. Connect the connector.



23. INSTALL OUTER REAR VIEW MIRROR ASSEMBLY LH


B166364E01
  1. Temporarily install the mirror by inserting the claw on the mirror into the holes on the vehicle.

  1. Tighten the 3 nuts in the sequence shown in the illustration and install the mirror.

    Torque:
    7.8 N*m{ 80 kgf*cm , 69 in.*lbf }

  1. w/ Power Mirror Control System:
    Connect the connector labeled A.



24. INSTALL OUTER MIRROR CONTROL ECU ASSEMBLY (w/ Power Mirror Control System)


    B166706
  1. Install the ECU with the 2 screws.

  1. Connect the 2 ECU connectors.



25. INSTALL SEAT MEMORY SWITCH (w/ Seat Memory Switch)


    B166227
  1. Install the seat memory with the 2 screws.



26. INSTALL FRONT INNER DOOR GLASS WEATHERSTRIP LH


27. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH


    B165684E03
  1. Connect the 2 cables to the inside handle.

  1. Connect the connector.

  1. Attach the inside handle's knob to the door trim board.



    B166215E01
  1. Attach the 9 clips to install the door trim board.

  1. Install the inside handle and door trim board to the door trim panel with the screw.

  1. Install the door trim board to the door panel with the screw.

  1. Install the clip.



28. INSTALL FRONT DOOR ARMREST COVER LH


29. INSTALL FRONT NO. 3 SPEAKER ASSEMBLY


B165754E01
  1. Attach the 3 claws to install the speaker to the bracket.

    NOTICE:
    Do not touch the cone part of the speaker.



    B171783
  1. Install the speaker with bracket to the lower frame bracket garnish with the 3 screws.



30. INSTALL FRONT LOWER DOOR FRAME BRACKET GARNISH LH


    B168274E01
  1. Attach the 3 clips to install the front door lower frame bracket garnish.



31. INSTALL POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY


    B165650
  1. Install the power window regulator master switch with the 3 screws.



32. INSTALL FRONT UPPER ARMREST BASE PANEL LH


    B166211E01
  1. Connect the connectors.

  1. Attach the 2 clips to install the front armrest upper base panel.



33. INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG LH


    B165648E03
  1. Attach the 4 claws to install the bezel plug.



34. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL


35. CHECK SRS WARNING LIGHT
  1. Check the SRS warning light (Click here).