Home › BODY › ENGINE HOOD / DOOR › REAR DOOR (for Double Cab)

REAR DOOR (for Double Cab) > REASSEMBLY

for Preparation Click here


HINT:
  1. Use the same procedures for the RH side and LH side.
  2. The procedures listed below are for the LH side.
  3. A bolt without a torque specification is shown in the standard bolt chart (Click here).



1. INSTALL REAR DOOR WEATHERSTRIP LH


    B167089
  1. Attach the 34 clips to install the weatherstrip.

    HINT:
    If clips are damaged during installation, replace them.



2. INSTALL REAR DOOR CHECK ASSEMBLY LH


    B166256
  1. Apply MP grease to the sliding areas of the door check.

  1. Install the door check to the door panel with the 2 nuts.

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }

  1. Apply adhesive to the threads of the bolt.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

  1. Install the bolt.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }



3. INSTALL REAR NO. 2 DOOR WEATHERSTRIP LH


    B166257
  1. Attach the 7 clips to install the weatherstrip.



4. INSTALL REAR DOOR OUTSIDE HANDLE ASSEMBLY LH


    B166254
  1. Install the rear door outside handle with the 2 nuts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

  1. Install the 2 hole plugs.



5. INSTALL REAR DOOR LOCK OPEN ROD LH


6. INSTALL REAR DOOR LOCK CHILD PROTECTION COVER LH


7. INSTALL REAR DOOR INSIDE LOCKING CABLE ASSEMBLY LH


    B167682E01
  1. Install the rear door inside locking cable.



    B266908
  1. Attach the 3 claws.



8. INSTALL REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH


    B165670E01
  1. Install the rear door lock remote control cable.



9. INSTALL REAR DOOR LOCK ASSEMBLY LH
  1. Apply MP grease to the sliding and rotating parts of the front door lock.

  1. Install a new door lock wire harness packing to the door lock.

    NOTICE:
    1. When reusing a door lock that has been removed, replace the packing in the connecting part with a new packing.
    2. Be careful that no grease or dirt sticks to the packing surface in the connecting part.
    3. Reusing removed packing or using damaged packing will allow water to penetrate through to the connecting part, resulting in a malfunction of the door lock.



    B166253
  1. Using a T30 ''TORX'' wrench, install the door lock with the 3 screws.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Connect the connector.



10. INSTALL POWER WINDOW REGULATOR MOTOR ASSEMBLY LH
  1. Apply MP grease to the sliding and rotating areas of the regulator motor.



    B166252
  1. Using a T25 ''TORX'' driver, install the motor with the 3 screws.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

    HINT:
    For a new front window regulator, the installation position of the regulator will be set when the self-tapping screws are installed.



11. INSTALL REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY LH
  1. Apply MP grease to the rear door power window regulator.



    B166251E02
  1. Loosely install the temporary bolt onto the window regulator.

  1. Insert the window regulator into the door panel. Use the temporary bolt to hang the window regulator on the door panel.

  1. Temporarily install the window regulator with the 3 bolts, and tighten the temporary bolt so that it contacts the door panel.

  1. Tighten the 4 bolts in the order shown in the illustration.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



12. INSTALL REAR OUTER DOOR GLASS WEATHERSTRIP


B165862
  1. Attach the claw to install the weatherstrip.



13. INSTALL REAR NO. 2 DOOR GLASS RUN LH
  1. Install the rear door glass run to the rear door window front lower guide.



14. INSTALL REAR DOOR FRONT WINDOW GUIDE SUB-ASSEMBLY LH


    B167093
  1. Install the rear door front window guide to the door panel with the 2 bolts.



15. INSTALL REAR DOOR GLASS SUB-ASSEMBLY LH


    B167085
  1. Slide the rear door glass to install it as shown in the illustration.

    NOTICE:
    Be careful not to damage the glass.



16. INSTALL REAR NO. 2 DOOR GLASS RUN LH
  1. Install the rear door glass run to the rear door window rear lower frame.



17. INSTALL REAR DOOR REAR LOWER WINDOW FRAME SUB-ASSEMBLY LH


    B166247
  1. Install the rear door rear lower window frame LH to the door panel with the 4 bolts.



18. INSTALL REAR DOOR GLASS RUN LH


    B166248
  1. Install the rear door glass run.



19. INSTALL REAR DOOR SERVICE HOLE COVER LH


    B166246
  1. Attach the 2 clamps to install the rear door service hole cover.

    NOTICE:
    1. When installing the service hole cover, pull out the links through the service hole cover.
    2. There should be no wrinkles or folds after attaching the service hole cover.
    3. After attaching the service hole cover, check the sealing quality.



20. INSTALL REAR SPEAKER ASSEMBLY



B166268E01

  1. Temporarily install the speaker by attaching the claws of the speaker to the door panel.

  1. Install the speaker with the 3 screws.

    NOTICE:
    Do not touch the cone part of the speaker.

    HINT:
    Install the screws in the order shown in the illustration.

  1. Connect the connector.



21. INSTALL REAR NO. 2 DOOR TRIM BRACKET


    B166245
  1. Install the bracket with the 2 screws.



22. INSTALL REAR INNER DOOR GLASS WEATHERSTRIP LH


23. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY LH


    B165684E03
  1. Connect the 2 cables to the inside handle.

  1. Attach the inside handle's knob to the door trim board.



    B166244E01
  1. Attach the 9 clips to install the door trim board.

  1. Install the inside handle and door trim board to the door trim panel with the screw.

  1. Install the door trim board to the door panel with the screw

  1. Attach the clip.



24. INSTALL REAR DOOR ARMREST COVER LH


25. INSTALL REAR DOOR FRAME GARNISH LH


    B167090
  1. Attach the 4 clips to install the rear door frame garnish.



26. INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY


    B166733
  1. Attach the 4 claws to install the control switch.



27. INSTALL REAR UPPER DOOR ARMREST BASE PANEL LH


    B168094
  1. Connect the connector.

  1. Attach the 2 clips to install the rear upper door armrest base panel.



28. INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG LH


    B168093
  1. Attach the 4 claws to install the bezel plug.



29. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL