Home › BODY ELECTRICAL › DOOR LOCK › FRONT DOOR LOCK (for Regular Cab)

FRONT DOOR LOCK (for Regular Cab) > INSTALLATION

for Preparation Click here


HINT:
  1. Use the same procedures for the LH side and RH side.
  2. The procedures listed below are for the LH side.
  3. A bolt without a torque specification is shown in the standard bolt chart (Click here).



1. INSTALL FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY LH


    B165672E02
  1. Install the front door inside locking cable.



    B266907
  1. Attach the 3 claws.



2. INSTALL FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH


    B165670E04
  1. Install the front door lock remote control cable.



3. INSTALL FRONT DOOR LOCK ASSEMBLY LH
  1. Apply MP grease to the sliding and rotating areas of the door lock.

  1. Install a new door lock wire harness packing to the door lock.

    NOTICE:
    1. When reusing a door lock that has been removed, replace the packing in the connecting part with new packing.
    2. Be careful that no grease or dirt sticks to the packing surface in the connecting part.
    3. Reusing removed packing or using damaged packing will allow water to penetrate through to the connecting part, resulting in a malfunction of the door lock.



    B165669
  1. Using a T30 ''TORX'' wrench, install the door lock with the 3 screws.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Connect the door lock connector.



4. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY LH


    B165661E01
  1. Insert the door glass into the door panel along the glass run as indicated by the arrows in the illustration.

    NOTICE:
    Be careful not to damage the glass.



    B165660
  1. Install the door glass to the window regulator with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Install the hole plug.



5. INSTALL FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY LH


    B165682
  1. Install the frame with the 2 bolts.



6. INSTALL FRONT DOOR SERVICE HOLE COVER LH
  1. Install the front door service hole cover to the door panel.

    NOTICE:
    1. When installing the service hole cover, pull out the links through the service hole cover.
    2. There should be no wrinkles or folds after attaching the service hole cover.
    3. After attaching the service hole cover, check the sealing quality.

  1. Connect the clamp.



7. INSTALL FRONT NO. 1 DOOR TRIM BRACKET


    B165656
  1. Install the bracket with the 2 screws.



8. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH


    B165684E03
  1. Connect the 2 cables to the inside handle.

  1. Attach the inside handle's knob to the door trim board.

  1. Attach the 10 clips to install the door trim board.



    B167314E01
  1. Install the inside handle and door trim board to the door trim panel with the screw.

  1. Install the door trim board to the door panel with the screw.

  1. Attach the clip.



9. INSTALL FRONT DOOR ARMREST COVER LH


10. INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH LH


    B165652
  1. Attach the 3 clips to install the front lower door frame bracket garnish.



11. INSTALL FRONT DOOR WINDOW REGULATOR HANDLE ASSEMBLY (w/o Power Window)


    B165697E01
  1. Install the plate and regulator handle with the snap ring.

    HINT:
    With the door window fully closed, install the plate and the regulator handle with the snap ring as shown in the illustration.



12. INSTALL FRONT ARMREST UPPER BASE PANEL LH


    B165649E01
  1. Connect the connectors.

  1. Attach the 2 clips to install the front upper armrest base panel.



13. INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG LH


    B165648E01
  1. Attach the 4 claws to install the bezel plug.



14. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL