Home › BODY ELECTRICAL › DOOR LOCK › FRONT DOOR LOCK (for Regular Cab)

FRONT DOOR LOCK (for Regular Cab) > REMOVAL

for Preparation Click here


HINT:
  1. Use the same procedures for the LH side and RH side.
  2. The procedures listed below are for the LH side.



1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


3. REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG LH


    B165648
  1. Using a screwdriver, detach the 4 claws and remove the inside handle bezel.

    HINT:
    Tape the screwdriver tip before use.



4. REMOVE FRONT ARMREST UPPER BASE PANEL LH


    B165649
  1. Using a screwdriver, detach the 2 clips and front upper armrest base panel.

    HINT:
    Tape the screwdriver tip before use.

  1. Disconnect the connectors.



5. REMOVE FRONT DOOR WINDOW REGULATOR HANDLE ASSEMBLY (w/o Power Window)


    B084267E03
  1. Insert a clip remover between the plate and trim.

  1. Turn the handle clockwise to remove the handle.



6. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH LH


    B165652
  1. Detach the 3 clips and front lower door frame bracket garnish.



7. REMOVE FRONT DOOR ARMREST COVER LH


8. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH


    B167314E01
  1. Remove the 2 screws.

  1. Using a clip remover, remove the clip.

  1. Detach the 10 clips and remove the trim cover. Then disconnect the connector.



    B165654E01
  1. Disconnect the 2 cables from the inside handle.

  1. Remove the inside handle.



9. REMOVE FRONT NO. 1 DOOR TRIM BRACKET


    B165656
  1. Remove the 2 screws and bracket.



10. REMOVE FRONT DOOR SERVICE HOLE COVER LH


    B165657
  1. Using a clip remover, detach the 2 clamps.



    B165658
  1. Remove the front door service hole cover.

    HINT:
    Remove the remaining tape on the door.



11. REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY LH


    B165664
  1. Remove the 2 bolts and front door rear lower frame.

    HINT:
    Remove the frame through the service hole.

    NOTICE:
    Be careful when removing the bolts as the frame may fall and become damaged.



12. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY LH
  1. for Driver Side:

    1. Temporarily install the power window regulator master switch.

  1. for Passenger Side:

    1. Temporarily install the power window regulator switch.

  1. Connect the cable to the negative (-) battery terminal.

  1. Remove the hole plug.



    B165660
  1. Move the door glass until the bolts appear in the service holes.

  1. Remove the 2 bolts.

    NOTICE:
    Be careful when removing the bolts as the glass may fall and become damaged.



    B165661
  1. Remove the door glass in the direction indicated by the arrows in the illustration.

    HINT:
    Remove the glass upward.

    NOTICE:
    Be careful not to damage the glass.

  1. for Driver Side:

    1. Remove the power window regulator master switch.

  1. for Passenger Side:

    1. Remove the power window regulator switch.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.



13. REMOVE FRONT DOOR LOCK ASSEMBLY LH


    B165669E02
  1. Disconnect the connector.

  1. Using a T30 "TORX" wrench, remove the 3 screws and door lock.

    HINT:
    Remove the door lock through the service hole.

    NOTICE:
    Be careful when removing the bolts as the door lock may fall and become damaged.



14. REMOVE FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH


    B165670E01
  1. Remove the front door lock remote control cable assembly.



15. REMOVE FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY LH


    B165671E02
  1. Using a screwdriver, detach the 3 claws.

    HINT:
    Tape the screwdriver tip before use.



    B165672E01
  1. Remove the front door inside locking cable assembly.