Home › BODY ELECTRICAL › NAVIGATION › NAVIGATION RECEIVER (for Floor Shift Type)

NAVIGATION RECEIVER (for Floor Shift Type) > INSTALLATION

for Preparation Click here



1. INSTALL NO. 2 RADIO BRACKET (for SD)


    E232004
  1. Install the bracket with the 4 bolts.

    Torque:
    4.5 N*m{ 45 kgf*cm , 39 in.*lbf }



2. INSTALL NO. 1 RADIO BRACKET (for SD)


    E232003
  1. Install the bracket with the 4 bolts.

    Torque:
    4.5 N*m{ 45 kgf*cm , 39 in.*lbf }



3. INSTALL UPPER INSTRUMENT CLUSTER FINISH PANEL (for SD)


    B229213
  1. Install the upper instrument cluster finish panel with the 4 screws.



4. INSTALL NAVIGATION RECEIVER ASSEMBLY WITH BRACKET (for SD)


    E232005
  1. Connect the connectors.

  1. Insert the navigation receiver as shown in the illustration to attach the 2 clips on its backside.

    NOTICE:
    When inserting the navigation receiver, do not press the knobs on it.



    E232001
  1. Install the navigation receiver with the 4 bolts.

    Torque:
    8.0 N*m{ 81 kgf*cm , 70 in.*lbf }



5. INSTALL NO. 2 RADIO BRACKET (for DVD)


    B164794
  1. Install the bracket with the 4 bolts.



6. INSTALL NO. 1 RADIO BRACKET (for DVD)


    B164795
  1. Install the bracket with the 4 bolts.



7. INSTALL NAVIGATION RECEIVER ASSEMBLY WITH BRACKET (for DVD)


    E159006
  1. Connect the connectors.

  1. Insert the navigation receiver as shown in the illustration to attach the 3 clips on its backside.

    NOTICE:
    When inserting the navigation receiver, do not press the knobs on it.



    B164792
  1. Install the navigation receiver with the 4 bolts.



8. INSTALL INTEGRATION CONTROL AND PANEL ASSEMBLY (for Manual Air Conditioning System)


    B160589
  1. Connect the connectors.

  1. Attach the 4 clips to install the panel.



9. INSTALL INTEGRATION CONTROL AND PANEL ASSEMBLY (for Automatic Air Conditioning System)


    B160588
  1. Connect the connectors.

  1. Attach the 4 clips to install the panel.



10. INSTALL CENTER LOWER INSTRUMENT PANEL FINISH PANEL


    B161747
  1. Connect the connectors.

  1. Attach the 4 clips to install the finish panel.



11. INSTALL INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY


    B227982
  1. Attach the 12 clips to install the finish panel.

  1. Connect the connector and attach the wire harness clamp.



12. INSTALL FRONT CONSOLE BOX


    B161746
  1. Install the front console box with the 6 screws and 2 clips.



13. INSTALL REAR CONSOLE BOX ASSEMBLY


    B227981
  1. Install the rear console box with the 2 screws and 4 bolts.

  1. Attach the 2 wire harness clamps.



14. INSTALL CONSOLE BOX CARPET
  1. Install the carpet.



15. INSTALL REAR CONSOLE END PANEL SUB-ASSEMBLY


    B227980
  1. except Regular Cab:
    Attach the 2 wire harness clamps and connect the connector.

  1. Attach the 7 clips to install the end panel.



16. INSTALL REAR UPPER CONSOLE PANEL SUB-ASSEMBLY
  1. w/ Trailer Towing System:
    Connect the connector.

  1. Attach the 6 clips to install the console panel.



  1. Install the clip.


    B171298



17. INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY


    B161742
  1. Attach the 12 clips to install the console panel.



18. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY


    B167312
  1. Install the shift lever knob and twist it in the direction indicated by the arrow.



19. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY LH


    B163883
  1. for Automatic Air Conditioning System:
    Attach the 2 claws to install the sensor.



    B226740
  1. Connect the connectors.

  1. Attach the 9 clips and claw to install the finish panel.

  1. Install the 2 bolts.

  1. Install the hood lock control lever.



20. INSTALL INSTRUMENT SIDE PANEL LH


    B229058
  1. Attach the 7 claws to install the side panel.



21. INSTALL COWL SIDE TRIM BOARD LH


B165704
  1. Attach the 2 clips to install the cowl side trim board.

  1. Install the clip.



22. INSTALL FRONT DOOR SCUFF PLATE LH
  1. for Double Cab:
    Install the front door scuff plate LH .

  1. for CrewMax:
    Install the front door scuff plate LH .



23. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL