Home › BODY ELECTRICAL › NAVIGATION › NAVIGATION RECEIVER (for Floor Shift Type)

NAVIGATION RECEIVER (for Floor Shift Type) > REMOVAL

for Preparation Click here



1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work. (Click here).



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


3. REMOVE FRONT DOOR SCUFF PLATE LH
  1. for Double Cab:
    Remove the front door scuff plate LH .

  1. for CrewMax:
    Remove the front door scuff plate LH .



4. REMOVE COWL SIDE TRIM BOARD LH


B165704
  1. Remove the clip.

  1. Detach the 2 clips and remove the cowl side trim board.



5. REMOVE INSTRUMENT SIDE PANEL LH


    B226739
  1. Using a moulding remover, detach the 7 claws and remove the side panel.



6. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY LH


    B226740
  1. Remove the hood lock control lever.

  1. Remove the 2 bolts.

  1. Detach the 9 clips and claw.



    B163883
  1. for Automatic Air Conditioning System:
    Detach the 2 claws and remove the sensor.

  1. Remove the finish panel and then disconnect the connectors.



7. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY


    B161741
  1. Twist the shift lever knob in the direction indicated by the arrow and remove it.



8. REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY


    B161742
  1. Detach the 12 clips and remove the console panel.



9. REMOVE REAR UPPER CONSOLE PANEL SUB-ASSEMBLY


    B227980
  1. Using a moulding remover, detach the 7 clips and remove the end panel.

  1. except Regular Cab:
    Detach the 2 wire harness clamps and disconnect the connector.



10. REMOVE REAR CONSOLE END PANEL SUB-ASSEMBLY


    B227980
  1. Using a moulding remover, detach the 7 clips and remove the end panel.

  1. except Regular Cab:
    Detach the 2 wire harness clamps and disconnect the connector.



11. REMOVE CONSOLE BOX CARPET


12. REMOVE REAR CONSOLE BOX ASSEMBLY


    B227981
  1. Remove the 2 screws.

  1. Detach the 2 wire harness clamps.

  1. Remove the 4 bolts and rear console box.



13. REMOVE FRONT CONSOLE BOX


    B161746
  1. Remove the 2 clips.

  1. Remove the 6 screws and front console box.



14. REMOVE INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY


    B227982
  1. Disconnect the connector and detach the wire harness clamp.

  1. Detach the 12 clips and remove the finish panel.



15. REMOVE CENTER LOWER INSTRUMENT PANEL FINISH PANEL


    B161747
  1. Detach the 4 clips and remove the finish panel.

  1. Disconnect the connectors.



16. REMOVE INTEGRATION CONTROL AND PANEL ASSEMBLY (for Manual Air Conditioning System)


    B160589
  1. Detach the 4 clips and remove the panel.

  1. Disconnect the connectors.



17. REMOVE INTEGRATION CONTROL AND PANEL ASSEMBLY (for Automatic Air Conditioning System)


    B160588
  1. Detach the 4 clips and remove the panel.

  1. Disconnect the connectors.



18. REMOVE NAVIGATION RECEIVER ASSEMBLY WITH BRACKET (for DVD)


B164792
  1. Remove the 4 bolts.



    E159005
  1. Pull the navigation receiver as shown in the illustration to detach the 3 clips on the backside of the navigation receiver.

  1. Disconnect the connectors and remove the navigation receiver.



19. REMOVE NO. 1 RADIO BRACKET (for DVD)


    B164795
  1. Remove the 4 bolts and bracket.



20. REMOVE NO. 2 RADIO BRACKET (for DVD)


    B164794
  1. Remove the 4 bolts and bracket.



21. REMOVE NAVIGATION RECEIVER ASSEMBLY WITH BRACKET (for SD)


    E232001
  1. Remove the 4 bolts.



    E232002
  1. Pull the navigation receiver as shown in the illustration to detach the 2 clips on the backside of the navigation receiver.

  1. Disconnect the connectors and remove the navigation receiver.



22. REMOVE UPPER INSTRUMENT CLUSTER FINISH PANEL (for SD)


    B229213
  1. Remove the 4 screws and upper instrument cluster finish panel.



23. REMOVE NO. 1 RADIO BRACKET (for SD)


    E232003
  1. Remove the 4 bolts and bracket.



24. REMOVE NO. 2 RADIO BRACKET (for SD)


    E232004
  1. Remove the 4 bolts and bracket.