Home › TRANSMISSION · AB60E AUTOMATIC TRANSMISSION › SHIFT LOCK SYSTEM

SHIFT LOCK SYSTEM > ON-VEHICLE INSPECTION

for Preparation Click here



1. CHECK SHIFT LOCK OPERATION
  1. Move the shift lever to P.

  1. Turn the ignition switch OFF.

  1. Check that the shift lever cannot be moved to any position other than P.

  1. Turn the ignition switch ON, depress the brake pedal and check that the shift lever can be moved to other positions.



2. CHECK SHIFT LOCK RELEASE BUTTON OPERATION
  1. When operating the shift lever with the shift lock release button pressed, check that the lever can be moved to any position other than P.
    If the operation cannot be performed as specified, check the shift lever assembly.



3. CHECK KEY INTERLOCK OPERATION
  1. Turn the ignition switch ON.

  1. Depress the brake pedal and move the shift lever to any position other than P.

  1. Check that the ignition switch cannot be turned OFF.

  1. Move the shift lever to P, turn the ignition switch OFF and check that the key can be removed.
    If the results are not as specified, inspect the shift lock control ECU.



4. CHECK SHIFT LOCK CONTROL ECU (for Column Shift Type)


C158387E02
  1. Measure the voltage according to the value(s) in the table below.

    HINT:
    Measure the voltage of the connector.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    J30-8 (KLS+) - J30-10 (E)
    Ignition switch ACC and shift lever on P
    Below 1 V
    J30-8 (KLS+) - J30-10 (E)
    Ignition switch ACC and shift lever not on P
    7.5 to 11 V
    J30-8 (KLS+) - J30-10 (E)
    Ignition switch ACC and shift lever not on P (after approx. 1 second)
    6 to 9 V
    J30-3 (ACC) - J30-10 (E)
    Ignition switch ON
    10 to 14 V
    J30-3 (ACC) - J30-10 (E)
    Ignition switch ACC
    10 to 14 V
    J30-3 (ACC) - J30-10 (E)
    Ignition switch OFF
    Below 1 V
    J30-13 (STP) - J30-10 (E)
    Brake pedal depressed
    10 to 14 V
    J30-13 (STP) - J30-10 (E)
    Brake pedal released
    Below 1 V
    J30-4 (IG) - J30-10 (E)
    Ignition switch ON
    10 to 14 V
    J30-4 (IG) - J30-10 (E)
    Ignition switch OFF
    Below 1 V

    If the result is not as specified, replace the shift lock control ECU.

  1. Measure the resistance according to the value(s) in the table below.

    NOTICE:
    Do not disconnect the shift lock control ECU connector.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    J30-10 (E) - Body ground
    Always
    Below 1 Ω

    If the result is not as specified, replace the shift lock control ECU.



5. CHECK SHIFT LOCK CONTROL ECU (for Floor Shift Type)


C158388E02
  1. Measure the voltage according to the value(s) in the table below.

    HINT:
    Measure the voltage of the connector.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    J27-5 (KLS+) - J27-1 (E)
    Ignition switch ACC and shift lever on P
    Below 1 V
    J27-5 (KLS+) - J27-1 (E)
    Ignition switch ACC and shift lever not on P
    7.5 to 11 V
    J27-5 (KLS+) - J27-1 (E)
    Ignition switch ACC and shift lever not on P (after approx. 1 second)
    6 to 9 V
    J27-6 (ACC) - J27-1 (E)
    Ignition switch ON
    10 to 14 V
    J27-6 (ACC) - J27-1 (E)
    Ignition switch ACC
    10 to 14 V
    J27-6 (ACC) - J27-1 (E)
    Ignition switch OFF
    Below 1 V
    J27-4 (STP) - J27-1 (E)
    Brake pedal depressed
    10 to 14 V
    J27-4 (STP) - J27-1 (E)
    Brake pedal released
    Below 1 V
    J27-8 (IG) - J27-1 (E)
    Ignition switch ON
    10 to 14 V
    J27-8 (IG) - J27-1 (E)
    Ignition switch OFF
    Below 1 V

    If the result is not as specified, replace the shift lock control ECU.

  1. Measure the resistance according to the value(s) in the table below.

    NOTICE:
    Do not disconnect the shift lock control ECU connector.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (E) - Body ground
    Always
    Below 1 Ω

    If the result is not as specified, replace the shift lock control ECU.



6. CHECK SHIFT LOCK SOLENOID (for Column Shift Type)


C159631E02
  1. Disconnect the transmission control switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (SLS+) - 8 (E)
    Always
    24 to 26 Ω

    If the result is not as specified, replace the shift lock solenoid.



7. CHECK SHIFT LOCK SOLENOID (for Floor Shift Type)


C150404E09
  1. Disconnect the shift lock solenoid connector from the shift lock control ECU.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    4 (SLS+) - 3 (SLS-)
    Always
    101 to 123 Ω

    If the result is not as specified, replace the floor shift assembly.



8. CHECK KEY INTERLOCK SOLENOID


C159632E03
  1. Disconnect the solenoid connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (SOL+) - 2 (SOL-)
    20°C (68°F)
    14.4 Ω

    If the result is not as specified, replace the solenoid.

  1. Connect the battery's positive (+) lead to terminal 1 (SOL+) and the battery's negative (-) lead to terminal 2 (SOL-).
    Check that the operating noise of the solenoid can be heard.
    If the result is not as specified, replace the solenoid.