Home › BODY › WINDSHIELD / WINDOWGLASS › BACK WINDOW GLASS (for CrewMax)

BACK WINDOW GLASS (for CrewMax) > INSTALLATION

for Preparation Click here


HINT:
A bolt without a torque specification is shown in the standard bolt chart (Click here).



1. INSTALL UPPER CAB REAR PILLAR PLATE LH


B168905E01
  1. Align the positioning hole with the claw, and install the upper plate with the 4 bolts as shown in the illustration.



2. INSTALL UPPER CAB REAR PILLAR PLATE RH

HINT:
Use the same procedures described for the LH side.



3. INSTALL BACK WINDOW OUTSIDE MOULDING


B171651
  1. Install the outside moulding with the 3 clips.



  1. Using an air riveter or hand riveter with a nose piece, install the back window outside moulding with 16 new rivets.


    B168907

    HINT:
    If the rivet cannot be cut, pull it once and cut it.

    NOTICE:

    1. B171664E01
    2. Do not pry the rivet with the riveter, as this will cause damage to the riveter and mandrel.

    3. B172390E01
      Confirm that the rivets are seated properly against the moulding.
    4. Do not tilt the riveter when installing the rivet to the moulding.
    5. Do not leave any space between the rivet head and moulding.

    6. B172391E01
      Do not leave any space between the moulding and door frame. Firmly hold together the 2 items while installing the rivet.



4. INSTALL BACK DOOR POWER WINDOW REGULATOR MOTOR


B171648
  1. Install the drum and wire guide to the motor.

  1. Install the cover with the 2 screws.

  1. Apply MP grease to the rotating areas of the regulator motor.



    B171645
  1. Install the motor with the 2 nuts.

    Torque:
    5.9 N*m{ 60 kgf*cm , 52 in.*lbf }



5. INSTALL BACK DOOR POWER WINDOW REGULATOR SUB-ASSEMBLY


B168908
  1. Apply MP grease to the sliding and rotating parts of the window regulator.

    NOTICE:
    Do not apply grease to the spring of the window regulator.



  1. Temporarily install the window regulator by attaching the 3 upper claws.


    B168904

  1. Loosely install the bolts onto the window regulator.

    NOTICE:
    Be careful not to drop and deform the window regulator.



  1. Tighten the 7 bolts in the order shown in the illustration.


    B168903E01

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



6. INSTALL BACK WINDOW GLASS
  1. Temporarily install the back window glass to the window regulator with the 4 bolts.

  1. Tighten the 4 bolts in the order shown in the illustration.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

    NOTICE:
    Do not damage the back window glass.



  1. Connect the 2 defogger connectors labeled A.


    B168902E02



7. INSTALL BACK DOOR GLASS RUN


B168901
  1. Install the glass run.



8. INSTALL INNER BACK DOOR GLASS WEATHERSTRIP


B168900
  1. Install the inner weatherstrip.



9. INSTALL OUTER BACK DOOR GLASS WEATHERSTRIP ASSEMBLY


  1. Install the outer weatherstrip with the 9 clips.


    B169099



10. INSTALL BACK DOOR SERVICE HOLE COVER
  1. Slide the cover to the right to engage the retainer labeled A.

  1. Attach the claw labeled B to the body.

  1. Install the 12 bolts and nut.



  1. Install the back window regulator connector labeled C.


    B168898E02



11. INSTALL ROOF HEADLINING ASSEMBLY
  1. Return the roof headlining to its original position. Refer to the following procedures .



12. INSTALL ASSIST GRIP PLUG


B165717
  1. Install a new assist grip plug.



13. INSTALL ASSIST GRIP SUB-ASSEMBLY


B169217

HINT:
Use the same procedure for the other 2 assist grips.

  1. Install the 2 clips and 2 covers to the assist grip, as shown in the illustration.

  1. Install the assist grip.



14. INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY LH


B169213
  1. Pass the rear seat outer belt floor anchor through the front quarter trim panel.

  1. Attach the 4 clips to install the quarter trim panel.

  1. Install the 2 bolts.



    B165712
  1. Attach the claw to install the cover.



15. INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.



16. INSTALL LOWER QUARTER TRIM PANEL ASSEMBLY LH


B169212
  1. Attach the 4 clips to install the lower quarter trim panel.



    B165831
  1. Connect the outer lap belt anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B165830
  1. Attach the 2 claws to install the cover.



17. INSTALL LOWER QUARTER TRIM PANEL ASSEMBLY RH


B173407
  1. Attach the 3 clips to install the lower quarter trim panel.



    B173410
  1. Connect the outer lap belt anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B173409
  1. Attach the 2 claws to install the cover.



18. INSTALL BACK PANEL TRIM LH
  1. Attach the 8 clips to install the back panel trim.



  1. Install the package holder net hook.


    B170105E05



19. INSTALL BACK PANEL TRIM RH


B169224E05
  1. Attach the 8 clips to install the back panel trim.

  1. Install the package holder net hook.



20. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH


21. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH


22. INSTALL REAR DOOR SCUFF PLATE LH


B169218
  1. Attach the 8 claws and 2 clips to install the rear door scuff plate.



23. INSTALL REAR DOOR SCUFF PLATE RH

HINT:
Use the same procedures described for the LH side.



24. INSTALL REAR SEAT ASSEMBLY LH


B165010E01
  1. Install the rear seat with the 5 bolts.

    Torque:
    for bolt A:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }
    for bolt B:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    1. Be careful not to damage the vehicle body.
    2. The anchor part of the seat belt must not overlap the protruding part.



25. INSTALL REAR SEAT ASSEMBLY RH


B165042
  1. Install the rear seat with the 4 bolts.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

    NOTICE:
    Be careful not to damage the vehicle body.



26. INSTALL REAR ROOF DRIP SIDE FINISH MOULDING LH
  1. Clean the vehicle body surface.

    1. Using a heat light, heat the vehicle body surface.

    2. Remove the double-sided tape from the vehicle body.

    3. Wipe off any tape adhesive residue with cleaner.



  1. If reusing the moulding:
    Clean the moulding.

    1. Using a heat light, heat the moulding.

    2. Remove the double-sided tape from the moulding.

    3. Wipe off any tape adhesive residue with cleaner.



    4. B163286E01
    5. Apply new double-sided tape to the moulding, as shown in the illustration.



  1. Install the moulding.

    1. Using a heat light, heat the vehicle body and moulding.

    2. Remove the peeling paper from the face of the moulding.

      HINT:
      After removing the peeling paper, keep the exposed adhesive free from foreign matter.



    3. B163282E03
    4. Attach the clip to install the moulding.

      HINT:
      Press the moulding firmly to install it.



27. INSTALL REAR ROOF DRIP SIDE FINISH MOULDING RH

HINT:
Use the same procedures described for the LH side.



28. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL