Home › DRIVE LINE › JF1A TRANSFER › TOUCH SELECT 2-4 AND HIGH-LOW SYSTEM

TOUCH SELECT 2-4 AND HIGH-LOW SYSTEM > TERMINALS OF ECU

for Preparation Click here



CHECK 4WD CONTROL ECU

C159461E01

  1. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbols)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    A25-1 (HL1) - A26-4 (GND)
    BE - W-B
    High-low transfer shift actuator limit switch
    Ignition switch ON
    4WD control switch 4H
    Below 1.5 V
    Ignition switch ON
    4WD control switch 4L
    10.5 to 14 V
    A25-2 (HL2) - A26-4 (GND)
    R - W-B
    High-low transfer shift actuator limit switch
    Ignition switch ON
    4WD control switch 4H
    10.5 to 14 V
    Ignition switch ON
    4WD control switch 4L
    Below 1.5 V
    A25-3 (HL3) - A26-4 (GND)
    GR - W-B
    High-low transfer shift actuator limit switch
    Ignition switch ON
    4WD control switch 4H
    10.5 to 14 V
    Ignition switch ON
    1.5 seconds or less after 4WD HIGH to 4WD LOW switching operation
    Below 1.5 V
    Ignition switch ON
    Over 1.5 seconds after 4WD HIGH to 4WD LOW switching operation
    10.5 to 14 V
    A25-5 (TT) - A25-25 (TGND)
    L - P
    Temperature sensor
    Ignition switch ON
    0 to 5 V
    A25-6 (TL1) - A26-4 (GND)
    V - W-B
    2WD-4WD transfer shift actuator limit switch
    Ignition switch ON
    4WD control switch 2WD
    Below 1.5 V
    Ignition switch ON
    4WD control switch 4H or 4L
    10.5 to 14 V
    A25-8 (TL3) - A26-4 (GND)
    W - W-B
    2WD-4WD transfer shift actuator limit switch
    Ignition switch ON
    4WD control switch 2WD
    10.5 to 14 V
    Ignition switch ON
    4WD control switch 4L
    Below 1.5 V
    A25-9 (DL1) - A26-4 (GND)
    LG - W-B
    A.D.D. actuator limit switch
    Ignition switch ON
    4WD control switch 2WD (A.D.D. actuator Free)
    10.5 to 14 V
    Ignition switch ON
    4WD control switch 4H (A.D.D. actuator Lock)
    Below 1.5 V
    A25-10 (DL2) - A26-4 (GND)
    R - W-B
    A.D.D. actuator limit switch
    Ignition switch ON
    4WD control switch 2WD (A.D.D. actuator Free)
    Below 1.5 V
    Ignition switch ON
    4WD control switch 4H (A.D.D. actuator Lock)
    10.5 to 14 V
    A25-11 (2-4) - A26-4 (GND)
    B - W-B
    4WD control switch
    Ignition switch ON
    4WD control switch 2WD or 4H
    Below 1.5 V
    Ignition switch ON
    4WD control switch 4L
    10.5 to 14 V
    A25-13 (LO) - A26-4 (GND)
    P - W-B
    4WD control switch
    Ignition switch ON
    4WD control switch 2WD
    10.5 to 14 V
    Ignition switch ON
    4WD control switch 4H or 4L
    Below 1.5 V
    A25-14 (4WD) - A26-4 (GND)
    SB - W-B
    2WD-4WD transfer shift actuator 4WD detection switch
    Ignition switch ON
    4WD control switch 2WD
    9.5 to 14 V
    Ignition switch ON
    4WD control switch 4H
    Below 1.5 V
    A25-15 (ADD) - A26-4 (GND)
    W - W-B
    A.D.D. actuator A.D.D. detection switch
    Ignition switch ON
    4WD control switch 2WD
    10 to 14 V
    Ignition switch ON
    4WD control switch 4H
    Below 1.5 V
    A25-16 (NP) - A26-4 (GND)
    B - W-B
    2WD-4WD transfer shift actuator neutral detection switch
    Ignition switch ON
    1.5 seconds or less after 4WD HIGH to 4WD LOW switching operation
    Below 1.5 V
    Ignition switch ON
    Over 1.5 seconds after 4WD HIGH to 4WD LOW switching operation
    10 to 14 V
    A25-19 (CANH) - A25-20 (CANL)
    BE - W
    CAN communication line
    Ignition switch OFF
    54 to 69 Ω
    A25-21 (L4) - A26-4 (GND)
    Y - W-B
    Transfer 4LO signal
    Except 4WD control switch 4L
    10 to 14 V
    Ignition switch ON
    4WD control switch 4L
    Below 1.5 V
    A26-1 (DM1) - A26-4 (GND)
    W - W-B
    A. D. D. actuator motor
    Ignition switch ON
    4WD control switch 4H (During operation of A.D.D. actuator from Lock to Free)
    10 to 14 V
    Ignition switch ON
    4WD control switch 4H (A.D.D. actuator Free)
    Below 1.5 V
    A26-2 (HM1) - A26-4 (GND)
    GR - W-B
    High-low transfer shift actuator motor
    Ignition switch ON
    4WD control switch 4L → 4H (During operation of high-low transfer shift actuator motor from 4WD LOW to 4WD HIGH)
    10 to 14 V
    Ignition switch ON
    4WD control switch 4L → 4H (High-low transfer shift actuator motor stopped)
    Below 1.5 V
    A26-3 (IG) - A26-4 (GND)
    V - W-B
    IG power
    Ignition switch ON
    11 to 14 V
    A26-4 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    A26-5 (DM2) - A26-4 (GND)
    Y - W-B
    A. D. D. actuator motor
    Ignition switch ON
    4WD control switch 4H (during operation of A.D.D. actuator from Free to Lock)
    10 to 14 V
    Ignition switch ON
    4WD control switch 4H (A.D.D. actuator Lock)
    Below 1.5 V
    A26-6 (HM2) - A26-4 (GND)
    P - W-B
    High-low transfer shift actuator motor
    Ignition switch ON
    4WD control switch 4H → 4L (During operation of high-low transfer shift actuator motor from 4WD HIGH to 4WD LOW)
    10 to 14 V
    Ignition switch ON
    4WD control switch 4H → 4L (High-low transfer shift actuator motor stopped)
    Below 1.5 V
    A26-7 (TM2) - A26-4 (GND)
    LG - W-B
    2WD-4WD transfer shift actuator motor
    Ignition switch ON
    4WD control switch 4H → 2WD (During operation of 2WD-4WD transfer shift actuator motor from 4WD HIGH to 2WD)
    10 to 14 V
    Ignition switch ON
    4WD control switch 4H → 2WD (2WD-4WD transfer shift actuator motor stopped)
    Below 1.5 V
    A26-8 (TM1) - A26-4 (GND)
    R - W-B
    2WD-4WD transfer shift actuator motor
    Ignition switch ON
    4WD control switch 2WD → 4H (During operation of 2WD-4WD transfer shift actuator motor from 2WD to 4WD HIGH)
    10 to 14 V
    Ignition switch ON
    4WD control switch 2WD → 4H (2WD-4WD transfer shift actuator motor stopped)
    Below 1.5 V