Home › SECURITIES › THEFT DETERRENT › THEFT DETERRENT SYSTEM

THEFT DETERRENT SYSTEM > Ignition Switch Circuit


DESCRIPTION

The main body ECU determines the ignition switch position (OFF, ON, ACC or engine running) based on signals from the IG circuit.

WIRING DIAGRAM


B165956E01


INSPECTION PROCEDURE

1.READ VALUE USING TECHSTREAM (IGNITION SWITCH)
  1. Using the Techstream, read the Data List.

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    IG SW
    Ignition switch / ON or OFF
    ON: Ignition switch ON
    OFF: Ignition switch OFF
    -

    OK:
    When the ignition switch is operated, "ON" is displayed on the Techstream screen.



NG
Go to step 2
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

2.INSPECT FUSE (AM1, ECU-IG No. 2)
  1. Remove the AM1 and ECU-IG No. 2 fuses from the main body ECU.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    AM1 fuse
    Always
    Below 1 Ω
    ECU-IG No. 2 fuse



NG
REPLACE FUSE
OK


3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BATTERY)


    B165958E01
  1. Disconnect the DA main body ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    DA-1 (IG) - Body ground
    Always
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.INSPECT IGNITION SWITCH
B165960E01
  1. Remove the ignition switch.

    1. For 1GR-FE, refer to the following procedures (Click here).

    2. For 1UR-FE, refer to the following procedures (Click here).

    3. For 3UR-FE, refer to the following procedures (Click here).

    4. For 3UR-FBE, refer to the following procedures (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 (IG1) - 4 (AM1)
    Ignition switch ON
    Below 1 Ω

    Result 
    Result
    Proceed to
    OK
    A
    NG
    (for 1GR-FE)
    B
    NG
    (for 1UR-FE)
    C
    NG
    (for 3UR-FE)
    D
    NG
    (for 3UR-FBE)
    E



B
REPLACE IGNITION SWITCH (Click here)

C
REPLACE IGNITION SWITCH (Click here)

D
REPLACE IGNITION SWITCH (Click here)

E
REPLACE IGNITION SWITCH (Click here)
A


5.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - IGNITION SWITCH AND BODY GROUND)
B165959E01
  1. Disconnect the DD main body ECU connector.

  1. Disconnect the J9 ignition switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    DD-47 - J9-4 (AM1)
    Always
    Below 1 Ω
    DD-43 - J9-1 (IG1)
    DD-62 - Body ground
    DD-47 - Body ground
    Always
    10 kΩ or higher
    DD-43 - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU