Home › BODY › WINDSHIELD / WINDOWGLASS › POWER WINDOW REGULATOR MOTOR (for Front Door)

POWER WINDOW REGULATOR MOTOR (for Front Door) > REMOVAL

for Preparation Click here


HINT:
  1. Use the same procedures for the LH side and RH side.
  2. The procedures listed below are for the LH side.



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.



2. REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG LH
  1. for Regular Cab:
    Remove the front door inside handle bezel plug LH .

  1. for Double Cab:
    Remove the front door inside handle bezel plug LH .

  1. for CrewMax:
    Remove the front door inside handle bezel plug LH .



3. REMOVE FRONT UPPER ARMREST BASE PANEL LH
  1. for Regular Cab:
    Remove the front upper armrest base panel LH .

  1. for Double Cab:
    Remove the front upper armrest base panel LH .

  1. for CrewMax:
    Remove the front upper armrest base panel LH .



4. REMOVE FRONT LOWER DOOR FRAME BRACKET GARNISH LH
  1. for Regular Cab:
    Remove the front lower door frame bracket garnish LH .

  1. for Double Cab:
    Remove the front lower door frame bracket garnish LH .

  1. for CrewMax:
    Remove the front lower door frame bracket garnish LH .



5. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH
  1. for Regular Cab:
    Remove the front door trim board sub-assembly LH .

  1. for Double Cab:
    Remove the front door trim board sub-assembly LH .

  1. for CrewMax:
    Remove the front door trim board sub-assembly LH .



6. REMOVE FRONT NO. 1 SPEAKER ASSEMBLY
  1. for Regular Cab:
    Remove the front No. 1 speaker assembly .

  1. for Double Cab:
    Remove the front No. 1 speaker assembly .

  1. for CrewMax:
    Remove the front No. 1 speaker assembly .



7. REMOVE FRONT NO. 1 DOOR TRIM BRACKET
  1. for Regular Cab:
    Remove the front No. 1 door trim bracket .

  1. for Double Cab:
    Remove the front No. 1 door trim bracket .

  1. for CrewMax:
    Remove the front No. 1 door trim bracket .



8. REMOVE FRONT DOOR SERVICE HOLE COVER LH
  1. for Regular Cab:
    Remove the front door service hole cover LH .

  1. for Double Cab:
    Remove the front door service hole cover LH .

  1. for CrewMax:
    Remove the front door service hole cover LH .



9. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY LH
  1. for Regular Cab:
    Remove the front door glass sub-assembly LH .

  1. for Double Cab:
    Remove the front door glass sub-assembly LH .

  1. for CrewMax:
    Remove the front door glass sub-assembly LH .



10. REMOVE FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY LH
  1. for Regular Cab:
    Remove the front door window regulator sub-assembly .

  1. for Double Cab:
    Remove the front door window regulator sub-assembly .

  1. for CrewMax:
    Remove the front door window regulator sub-assembly .



11. REMOVE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH


  1. Using a T25 "TORX" driver, remove the 3 screws and motor.


    B231493E01

    CAUTION:
    Do not place your finger, etc. within the range of movement of the window regulator. When removing the power window regulator motor, the force of the spring causes the window regulator to move in the direction of the arrow shown in the illustration (the direction in which the window rises), which may cause injury.

    NOTICE:
    Be careful when removing the screws as the motor may fall and become damaged.