FRONT POWER SEAT MOTOR ASSEMBLY (for Power Seat) > REMOVAL |
| 1. REMOVE FRONT SEAT ASSEMBLY LH |
Remove the front seat (Click here).
| 2. REMOVE SLIDE AND VERTICAL POWER SEAT SWITCH KNOB LH |
![]() |
Apply protective tape around the cushion shield.
Using a screwdriver, detach the 2 claws and remove the knob.
| 3. REMOVE RECLINING POWER SEAT SWITCH KNOB LH |
![]() |
Using a screwdriver, detach the 2 claws and remove the knob.
| 4. REMOVE FRONT SEAT CUSHION SHIELD LH |
![]() |
Remove the hog rings and rubber bands of the seatback cover from the seat frame.
Remove the 2 screws.
![]() |
Remove the 3 screws.
Detach the 2 claws and remove the cushion shield.
Disconnect the switch connectors.
| 5. REMOVE FRONT SEAT INNER BELT ASSEMBLY LH |
Driver Side:
Disconnect the 2 connectors and detach the 4 clamps.
Passenger Side:
Disconnect the connector and detach the clamp.
![]() |
Remove the nut and front seat inner belt.
| 6. REMOVE INNER FRONT SEAT CUSHION SHIELD LH |
![]() |
Remove the screw.
Detach the 2 claws and clip, and then remove the cushion shield.
| 7. REMOVE FRONT POWER SEAT SWITCH LH |
![]() |
Disconnect the 2 connectors.
w/o Seat Position Memory System:
Disconnect the switch connector.
Remove the 3 screws and switch.
| 8. REMOVE FRONT SEAT CUSHION COVER WITH PAD LH |
![]() |
Using a clip remover, remove the 2 clips.
![]() |
Detach the wire harness clamp.
w/ Seat Heater System or Climate Control Seat System:
![]() |
Disconnect the seat heater connector and detach the 2 wire harness clamps.
![]() |
Disconnect the seat heater control connector and detach the 2 wire harness clamps.
w/ Leg Support Adjustment Switch:
![]() |
Remove the hog rings and detach the hooks.
![]() |
Remove the seat cushion cover wire.
Remove the seat cushion cover with pad from the seat frame.
![]() |
w/o Leg Support Adjustment Switch:
Remove the hog rings.
Bend the 2 seat frame claws upward.
Detach the hooks and remove the seat cushion cover with pad.
| 9. REMOVE FRONT SEATBACK COVER WITH PAD LH |
![]() |
Detach the hook.
![]() |
Remove the hog rings and seatback cover wires.
![]() |
Remove the nut and seatback cover bracket from the seat frame.
![]() |
Detach the 4 claws and remove the 2 headrest supports.
![]() |
Remove the hog rings and seatback cover with pad.
| 10. REMOVE RECLINING ADJUSTER INSIDE COVER LH |
![]() |
Remove the screw and detach the claw, and then remove the reclining adjuster inside cover.
| 11. REMOVE RECLINING ADJUSTER INSIDE COVER RH |
Remove the screw and detach the claw, and then remove the reclining adjuster inside cover.
| 12. REMOVE FRONT SEATBACK SHIELD LH |
![]() |
Remove the 2 screws.
Detach the claw and remove the seatback shield.
| 13. REMOVE FRONT SEATBACK SHIELD RH |
![]() |
Detach the wire harness clamp.
Remove the 2 screws.
Detach the claw and remove the seatback shield.
| 14. REMOVE LOWER FRONT SEAT CUSHION SHIELD LH |
![]() |
Remove the screw.
Detach the hook and remove the cushion shield.
| 15. REMOVE LOWER FRONT SEAT CUSHION SHIELD RH |
Remove the screw.
Detach the hook and remove the cushion shield.
| 16. REMOVE LUMBAR SUPPORT ADJUSTER ASSEMBLY LH (w/ Lumbar Support Adjuster) |
![]() |
w/o Climate Control Seat System:
Remove the 2 springs.
Detach the 6 hooks and remove the seatback spring.
![]() |
w/ Climate Control Seat System:
Remove the 4 springs.
Detach the 4 hooks and remove the seatback spring.
![]() |
Disconnect the lumbar support adjuster connector.
Remove the 2 screws and lumbar support adjuster.
![]() |
Detach the 3 claws and remove the bush from the seat frame.
| 17. REMOVE SEAT HEATER CONTROL SUB-ASSEMBLY LH (w/ Seat Heater System) |
![]() |
Disconnect the seat heater control connector and detach the clamp.
Using a screwdriver, detach the claw and remove the seat heater control.
| 18. REMOVE OCCUPANT CLASSIFICATION ECU (for Front Passenger Side) |
![]() |
Disconnect the 2 ECU connectors.
Using a screwdriver, detach the claw and remove the ECU.
| 19. REMOVE SEAT POSITION AIRBAG SENSOR |
![]() |
Using a T30 "TORX" socket wrench, remove the screw and seat position sensor with sensor protector.
Disconnect the connector.
Remove the seat slide position sensor protector from the seat position sensor.
| 20. REMOVE FRONT SEAT WIRE LH |