Home › ENGINE · 3UR-FBE › ENGINE CONTROL SYSTEM › SFI SYSTEM

SFI SYSTEM > Fuel Pump Control Circuit

for Preparation Click here


DESCRIPTION

The fuel pump circuit consists of the ECM, fuel pump and fuel pump ECU (which operates the fuel pump). Based on the engine output, the ECM determines the fuel pump speed. The speed is then converted to a duty signal and sent to the fuel pump ECU. Based on the signal sent from the ECM, the fuel pump ECU adjusts the fuel pump operation speed between 3 settings.

WIRING DIAGRAM


A165783E03


INSPECTION PROCEDURE

This troubleshooting procedure is based on the premise that the engine is started. If the engine is not started, proceed to the problem symptoms table (Click here).
1.PERFORM ACTIVE TEST USING TECHSTREAM (FUEL PUMP)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.

  1. Check whether operating sounds can be heard while operating the relay using the Techstream.

    OK:
    Operating sounds can be heard from relay.



NG
Go to step 5
OK


2.CHECK HARNESS AND CONNECTOR (FUEL PUMP ECU - ECM AND BODY GROUND)
  1. Disconnect the R7 fuel pump ECU connector.

  1. Disconnect the A24 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:

    Tester Connection
    Condition
    Specified Condition
    R7-1 (FPC) - A24-52 (FPC)
    Always
    Below 1 Ω
    R7-2 (DI) - A24-18 (DI)
    Always
    Below 1 Ω
    R7-3 (E) - Body ground
    Always
    Below 1 Ω
    R7-1 (FPC) or A24-52 (FPC) - Body ground
    Always
    10 kΩ or more
    R7-2 (DI) or A24-18 (DI) - Body ground
    Always
    10 kΩ or more



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.REPLACE FUEL PUMP ECU
  1. Replace the fuel pump ECU (Click here).


NEXT


4.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Check the fuel pump operation.

    OK:
    Malfunction has been repaired successfully.



NG
REPLACE ECM (Click here)
OK

END 

5.INSPECT CIRCUIT OPENING RELAY (C/OPN)
A035654E01
  1. Remove the circuit opening relay (C/OPN) from the engine room relay block (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    When no battery voltage applied to terminals 1 and 2
    10 kΩ or higher
    3 - 5
    When battery voltage applied to terminals 1 and 2
    Below 1 Ω



NG
REPLACE CIRCUIT OPENING RELAY (C/OPN) (Click here)
OK


6.INSPECT CIRCUIT OPENING RELAY (POWER SOURCE VOLTAGE)
A202084E01
  1. Remove the circuit opening relay (C/OPN) from the engine room relay block (Click here).

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    C/OPN relay (1) - Body ground
    Ignition switch ON
    11 to 14 V
    C/OPN relay (3) - Body ground
    Ignition switch ON
    11 to 14 V



NG
Go to step 13
OK


7.CHECK HARNESS AND CONNECTOR (CIRCUIT OPENING RELAY - ECM AND FUEL PUMP ECU)
  1. Remove the circuit opening relay (C/OPN) from the engine room relay block (Click here).

  1. Disconnect the A24 ECM connector.

  1. Disconnect the R7 fuel pump ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:

    Tester Connection
    Condition
    Specified Condition
    C/OPN relay (2) - A24-48 (FC)
    Always
    Below 1 Ω
    C/OPN relay (5) - R7-4 (+B)
    Always
    Below 1 Ω
    C/OPN relay (2) or A24-48 (FC) - Body ground
    Always
    10 kΩ or higher
    C/OPN relay (5) or R7-4 (+B) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8.CHECK HARNESS AND CONNECTOR (FUEL PUMP - FUEL PUMP ECU)
  1. Disconnect the R6 fuel pump connector.

  1. Disconnect the R8 fuel pump ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:

    Tester Connection
    Condition
    Specified Condition
    R6-4 (B2) - R8-1 (FP)
    Always
    Below 1 Ω
    R6-5 (E2) - R8-2 (FP-)
    Always
    Below 1 Ω
    R6-4 (B2) or R8-1 (FP) - Body ground
    Always
    10 kΩ or higher
    R6-5 (E2) or R8-2 (FP-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9.INSPECT FUEL PUMP
  1. Inspect the fuel pump .



NG
REPLACE FUEL PUMP (Click here)
OK


10.CHECK HARNESS AND CONNECTOR (FUEL PUMP ECU - ECM AND BODY GROUND)
  1. Disconnect the R7 fuel pump ECU connector.

  1. Disconnect the A24 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:

    Tester Connection
    Condition
    Specified Condition
    R7-1 (FPC) - A24-52 (FPC)
    Always
    Below 1 Ω
    R7-2 (DI) - A24-18 (DI)
    Always
    Below 1 Ω
    R7-3 (E) - Body ground
    Always
    Below 1 Ω
    R7-1 (FPC) or A24-52 (FPC) - Body ground
    Always
    10 kΩ or more
    R7-2 (DI) or A24-18 (DI) - Body ground
    Always
    10 kΩ or more



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


11.REPLACE FUEL PUMP ECU
  1. Replace the fuel pump ECU (Click here).


NEXT


12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Check the fuel pump operation.

    OK:
    Malfunction has been repaired successfully.



NG
REPLACE ECM (Click here)
OK

END 

13.CHECK HARNESS AND CONNECTOR (CIRCUIT OPENING RELAY - FUEL PUMP RELAY AND IGN FUSE)
A202086E01
  1. Remove the circuit opening relay (C/OPN) from the engine room relay block (Click here).

  1. Remove the fuel pump relay (F/PMP) from the engine room relay block (Click here).

  1. Remove the IGN fuse from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    C/OPN relay (1) - IGN fuse (2)
    Always
    Below 1 Ω
    C/OPN relay (3) - F/PMP relay (3)
    Always
    Below 1 Ω
    C/OPN relay (1) or IGN fuse (2) - Body ground
    Always
    10 kΩ or more
    C/OPN relay (3) or F/PMP relay (3) - Body ground
    Always
    10 kΩ or more



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


14.INSPECT FUEL PUMP RELAY (F/PMP)
B016200E02
  1. Remove the fuel pump relay (F/PMP) from the engine room relay block (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    When no battery voltage applied to terminals 1 and 2
    10 kΩ or higher
    3 - 5
    When battery voltage applied to terminals 1 and 2
    Below 1 Ω



NG
REPLACE FUEL PUMP RELAY (F/PMP) (Click here)
OK


15.CHECK HARNESS AND CONNECTOR (FUEL PUMP RELAY - INTEGRATION RELAY, BATTERY AND BODY GROUND)
A165848E01
  1. Remove the F/PMP fuse from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    F/PMP fuse
    Always
    Below 1 Ω

  1. Reinstall the F/PMP fuse.

  1. Remove the fuel pump relay (F/PMP) from the engine room relay block (Click here).

  1. Remove the integration relay from the engine room relay block (Click here).

  1. Disconnect the 1B integration relay connector.

  1. Disconnect the cable from the battery positive (+) terminal.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    F/PMP relay (1) - 1B-4
    Always
    Below 1 Ω
    F/PMP relay (5) - Positive (+) battery cable
    Always
    Below 1 Ω
    F/PMP relay (2) - Body ground
    Always
    Below 1 Ω
    F/PMP relay (1) or 1B-4 - Body ground
    Always
    10 kΩ or higher
    F/PMP relay (5) or Positive (+) battery cable - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

GO TO ECM POWER SOURCE CIRCUIT (Click here)