ENGINE UNIT > INSPECTION |
| 1. INSPECT CYLINDER HEAD SET BOLT |
![]() |
Using a vernier caliper, measure the diameter of the elongated thread at the measuring point.
| 2. INSPECT NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY |
![]() |
Turn the roller by hand to check that it turns smoothly.
If the roller does not turn smoothly, replace the valve rocker arm.
| 3. INSPECT VALVE LASH ADJUSTER ASSEMBLY |
![]() |
Place the lash adjuster into a container full of new engine oil.
Insert SST's tip into the lash adjuster's plunger and use the tip to press down on the check ball inside the plunger.
Squeeze SST and the lash adjuster together to move the plunger up and down 5 to 6 times.
Check the movement of the plunger and bleed air.
After bleeding the air, remove SST. Then try to quickly and firmly press the plunger with your fingers.
| 4. INSPECT CAMSHAFT SUB-ASSEMBLY |
![]() |
Inspect the camshaft for runout.
Place the camshaft on V-blocks.
Using a dial indicator, measure the circle runout at the center journal.
![]() |
Using a micrometer, measure the cam lobe height.
| Item | Specified Condition |
| Intake | 44.291 to 44.441 mm (1.744 to 1.750 in.) |
| Exhaust | 44.196 to 44.346 mm (1.740 to 1.746 in.) |
| Item | Specified Condition |
| Intake | 44.241 mm (1.742 in.) |
| Exhaust | 44.146 mm (1.738 in.) |
![]() |
Using a micrometer, measure the journal diameter.
| Item | Specified Condition |
| No. 1 journal | 29.956 to 29.970 mm (1.1793 to 1.1799 in.) |
| Other journals | 25.959 to 25.975 mm (1.0220 to 1.0226 in.) |
| 5. INSPECT CAMSHAFT TIMING GEAR |
Install the camshaft bearing cap .
Install the camshaft housing .
Apply a light coat of engine oil on the camshaft and camshaft timing gear.
![]() |
Using the hexagonal portion of the camshaft, align and attach the knock pin of the camshaft with the pin hole of the camshaft timing gear.
![]() |
![]() |
Apply a light coat of engine oil on the threads and under the head of the bolt.
Using a wrench to hold the hexagonal portion of the camshaft, install the camshaft timing gear with the bolt.
Remove the camshaft bearing cap .
Check the lock of the camshaft timing gear.
Clamp the camshaft in a vise, and confirm that the camshaft timing gear is locked.
![]() |
Release the lock pin.
Cover the 4 oil paths of the cam journal with vinyl tape as shown in the illustration.
Break through the tape of the advance side path. Then break through the tape of the retard side path on the opposite side of the advanced side path, as shown in the illustration.
![]() |
Apply approximately 200 kPa (2.0 kgf/cm2, 29 psi) of air pressure to the two broken paths.
![]() |
Check that the camshaft timing gear revolves in the advance direction when reducing the air pressure applied to the retard side path.
When the camshaft timing gear reaches the most advanced position, release the air pressure from the retard side path and advance side path, in that order.
Check for smooth rotation.
Turn the camshaft timing gear within its movable range (21°) 2 or 3 times, but do not turn it to the most retarded position. Make sure that the gear turns smoothly.
Check the lock in the most retarded position.
Confirm that the camshaft timing gear is locked at the most retarded position.
Install the camshaft bearing cap .
Install the camshaft housing .
![]() |
Hold the hexagonal portion of the camshaft with a wrench and loosen the bolt.
Remove the camshaft bearing cap .
![]() |
Remove the flange bolt and camshaft timing gear.
| 6. INSPECT CAMSHAFT TIMING EXHAUST GEAR |
Install the camshaft bearing cap .
Install the camshaft housing .
Apply a light coat of engine oil on the camshaft and camshaft timing exhaust gear.
![]() |
Using the hexagonal portion of the camshaft, align and attach the knock pin of the camshaft with the pin hole of the camshaft timing exhaust gear.
![]() |
Apply a light coat of engine oil on the threads and under the head of the bolt.
![]() |
Using a wrench to hold the hexagonal portion of the camshaft, install the camshaft timing exhaust gear with the bolt.
Remove the camshaft bearing cap .
Check the camshaft timing exhaust gear lock.
Make sure that the camshaft timing exhaust gear is locked.
![]() |
Release the lock pin.
Cover the 4 oil paths of the cam journal with vinyl tape as shown in the illustration.
Break through the tape of the advance side path. Then break through the tape of the retard side path on the opposite side of the advanced side path, as shown in the illustration.
![]() |
Apply approximately 200 kPa (2.0 kgf/cm2, 29 psi) of air pressure to the two broken paths (the advance side path and the retard side path).
![]() |
Check that the camshaft timing exhaust gear turns in the retard direction when reducing the air pressure applied to the advance side path.
When the camshaft timing exhaust gear moves to the most retarded position, release the air pressure from the advance side path, and then release the air pressure from the retard side path.
Check for smooth rotation.
Turn the camshaft timing exhaust gear within its movable range (18.5°) 2 or 3 times, but do not turn it to the most advanced position. Make sure that the gear turns smoothly.
Check the lock at the most advanced position.
Make sure that the camshaft timing exhaust gear is locked at the most advanced position.
Install the camshaft bearing cap .
Install the camshaft housing .
![]() |
Hold the hexagonal portion of the camshaft with a wrench and loosen the bolt.
Remove the camshaft bearing cap .
![]() |
Remove the flange bolt and camshaft timing exhaust gear.
| 7. INSPECT NO. 1 CHAIN SUB-ASSEMBLY |
![]() |
Using a spring scale, pull the chain with a force of 147 N (15 kgf, 33.1 lbf) as shown in the illustration.
Using a vernier caliper, measure the length of 15 pins.
| 8. INSPECT NO. 2 CHAIN SUB-ASSEMBLY |
![]() |
Using a spring scale, pull the chain with a force of 147 N (15 kgf, 33.1 lbf) as shown in the illustration.
Using a vernier caliper, measure the length of 15 pins.
| 9. INSPECT CRANKSHAFT TIMING SPROCKET RH |
![]() |
Wrap the chain around the sprocket.
Using a vernier caliper, measure the sprocket diameter with the chain.
| 10. INSPECT CRANKSHAFT TIMING SPROCKET LH |
![]() |
Wrap the chain around the sprocket.
Using a vernier caliper, measure the sprocket diameter with the chain.
| 11. INSPECT NO. 1 CHAIN TENSIONER ASSEMBLY |
![]() |
Move the stopper plate upward to release the lock. Push the plunger and check that it moves smoothly.
If necessary, replace the chain tensioner.
| 12. INSPECT NO. 2 CHAIN TENSIONER ASSEMBLY |
![]() |
Check that the plunger moves smoothly.
Measure the worn depth of the chain tensioner.
| 13. INSPECT NO. 3 CHAIN TENSIONER ASSEMBLY |
![]() |
Check that the plunger moves smoothly.
Measure the worn depth of the chain tensioner.
| 14. INSPECT NO. 1 CHAIN TENSIONER SLIPPER LH |
![]() |
Measure the worn depth of the chain tensioner slipper.
| 15. INSPECT NO. 1 CHAIN TENSIONER SLIPPER RH |
![]() |
Measure the worn depth of the chain tensioner slipper.
| 16. INSPECT NO. 1 CHAIN VIBRATION DAMPER LH |
![]() |
Measure the worn depth of the chain vibration damper.
| 17. INSPECT NO. 1 CHAIN VIBRATION DAMPER RH |
![]() |
Measure the worn depth of the chain vibration damper.
| 18. INSPECT EXHAUST MANIFOLD SUB-ASSEMBLY LH |
![]() |
Using a precision straightedge and feeler gauge, measure the warpage of the contact surface of the cylinder head.
| 19. INSPECT EXHAUST MANIFOLD SUB-ASSEMBLY RH |
![]() |
Using a precision straightedge and feeler gauge, measure the warpage of the contact surface of the cylinder head.