Home › ENGINE ยท 3UR-FE › EMISSION CONTROL › AIR PUMP

AIR PUMP > INSTALLATION

for Preparation Click here



1. INSTALL AIR PUMP ASSEMBLY


    A153467
  1. Connect the 6 air pump insulators to the air pump and install the air pump to the bracket.

  1. Attach the 2 wire harness clamps to the bracket.



2. INSTALL NO. 1 AIR INJECTION SYSTEM HOSE


    A158639E01
  1. Install the 2 No. 1 air injection system hoses to the air pump.

    HINT:
    Insert the hoses until the hose ends are aligned with the stoppers.



3. INSTALL AIR PUMP INLET


    A273867E01
  1. Connect the air pump inlet to the No. 1 air injection system hoses to install it, and then slide the 2 clips onto the hoses.

    HINT:
    Insert the inlet until the inlet stoppers are aligned with the hose ends.

  1. Install the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



4. INSTALL AIR PUMP ASSEMBLY WITH BRACKET


    A158660E01
  1. Install the air pump to the vehicle.

    1. Insert the bracket tab into the slot and insert the stud bolt into the bracket hole as shown in illustration A. Then slide the bracket.

    2. Insert the bracket tab into the slot shown in illustration B.

    3. Install the 2 bolts and 2 nuts.

      Torque:
      for bolt:
      18 N*m{ 184 kgf*cm , 13 ft.*lbf }
      for nut:
      12 N*m{ 122 kgf*cm , 9 ft.*lbf }



    A158597
  1. Connect the 2 air pump connectors and attach the 3 wire harness claws.



5. INSTALL NO. 3 AIR INJECTION SYSTEM HOSE
  1. Connect the No. 3 hose so that its paint mark aligns with the air pump's rib as shown in the illustration below labeled A.

  1. Connect the clamp to the No. 3 hose shown in the illustration below labeled B. Then insert the clamp's clip into the body hole.

    HINT:
    Align the paint mark of the No. 3 hose with the edge of the clamp.

  1. Connect the No. 3 hose to the air tube shown in the illustration below labeled C.

    HINT:
    1. Make sure the paint mark of the No. 3 hose is facing upward.
    2. Make sure the direction of the hose clamp is as shown in the illustration.

  1. Connect the clamp to the No. 3 hose and wire harness shown in the illustration below labeled D. Then insert the clamp's clip into the body hole.

    HINT:
    Align the paint mark of the No. 3 hose and paint mark of the wire harness with the edge of the clamp.



6. INSTALL NO. 2 AIR INJECTION SYSTEM HOSE
  1. Connect the No. 2 hose so that its paint mark aligns with the air pump's rib as shown in the illustration below labeled E.

  1. Connect the No. 2 hose to the air tube shown in the illustration below labeled F.

    HINT:
    1. Make sure the paint mark of the No. 2 hose is facing upward.
    2. Make sure the direction of the hose clamp is as shown in the illustration.

  1. Connect the white colored clamp to the No. 2 hose and wire harness shown in the illustration below labeled G.

    HINT:
    1. Make sure the paint mark of the No. 2 hose is facing upward.
    2. Make sure the direction of the hose clamp is as shown in the illustration.



  1. Connect the black colored clamp to the No. 2 hose and wire harness shown in the illustration below labeled H. Then insert the clamp's clip into the body hole.


    A158596E01



7. CONNECT FRONT FENDER APRON SEAL RH


    A164869
  1. Connect the fender apron seal with the 2 clips.



8. INSTALL FRONT FENDER LINER RH


    A160255
  1. Install the fender liner with the 9 clips.