EXHAUST MANIFOLD > INSTALLATION |
| 1. INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY RH |
![]() |
Install a new gasket to the cylinder head and a new gasket to the No. 2 air tube.
![]() |
Temporarily install the exhaust manifold with the 2 nuts labeled A and 8 new nuts.
Uniformly tighten the nuts that are not labeled A, and then tighten the 2 nuts labeled A.
| 2. INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR |
![]() |
Install the heat insulator with the 3 bolts.
| 3. INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY LH |
![]() |
Install a new gasket to the cylinder head and a new gasket to the No. 3 air tube.
![]() |
Temporarily install the exhaust manifold with the 2 nuts labeled A and 8 new nuts.
Uniformly tighten the nuts that are not labeled A, and then tighten the 2 nuts labeled A.
| 4. INSTALL NO. 2 EXHAUST MANIFOLD HEAT INSULATOR |
![]() |
Install the heat insulator with the 3 bolts.
| 5. INSTALL NO. 2 STEERING INTERMEDIATE SHAFT SUB-ASSEMBLY |
![]() |
Align the matchmarks and insert the No. 2 intermediate shaft into the intermediate shaft.
![]() |
Align the matchmarks and insert the No. 2 intermediate shaft into the power steering gear.
Install the 2 bolts.
| 6. INSTALL FRONT EXHAUST PIPE ASSEMBLY |
Install a new gasket and the front exhaust pipe to the exhaust manifold RH with 3 new nuts.
Install a new gasket and the front exhaust pipe to the center exhaust pipe with the 2 bolts.
Connect the air fuel ratio sensor connector.
Connect the heated oxygen sensor connector and 2 clamps.
| 7. INSTALL FRONT NO. 2 EXHAUST PIPE ASSEMBLY (except Regular Cab Standard Deck) |
Connect the front No. 2 exhaust pipe to the exhaust pipe support.
Install a new gasket and the front No. 2 exhaust pipe to the exhaust manifold LH with 3 new nuts.
Install a new gasket and the front No. 2 exhaust pipe to the center exhaust pipe with the 2 bolts.
Connect the air fuel ratio sensor connector.
Connect the heated oxygen sensor connector.
| 8. INSTALL FRONT NO. 2 EXHAUST PIPE ASSEMBLY (for Regular Cab Standard Deck) |
Install a new gasket and the front No. 2 exhaust pipe to the exhaust manifold LH with 3 new nuts.
Install a new gasket and the front No. 2 exhaust pipe to the front No. 3 exhaust pipe with the 2 bolts and 2 new nuts.
Connect the air fuel ratio sensor connector.
Connect the heated oxygen sensor connector.
| 9. INSTALL FRONT PROPELLER SHAFT ASSEMBLY |
![]() |
for Front Differential Side:
Align the matchmarks on the differential and propeller shaft flange.
Install the propeller shaft with the 4 washers and 4 nuts.
![]() |
for Transfer Side:
Align the matchmarks on the transfer and propeller shaft flange.
Connect the propeller shaft with the 4 washers and 4 nuts.
| 10. INSTALL PROPELLER SHAFT HEAT INSULATOR |
![]() |
Install the heat insulator with the 2 bolts.
| 11. CONNECT COOLER COMPRESSOR ASSEMBLY |
![]() |
Install the cooler compressor with the 2 stud bolts.
Install the 2 bolts and 2 nuts.
| 12. INSTALL GENERATOR ASSEMBLY |
![]() |
Install the generator with the 3 bolts and nut.
![]() |
Connect the generator connector.
Connect the generator wire with the nut.
Install the terminal cap.
![]() |
Install the harness bracket to the generator with the bolt.
| 13. CONNECT VANE PUMP ASSEMBLY |
![]() |
![]() |
Connect the vane pump to the timing chain cover with the 2 bolts.
![]() |
Attach the 2 clamps and connect the power steering oil pressure switch connector.
| 14. INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE |
Apply a light coat of engine oil to a new O-ring.
![]() |
Install the O-ring to the guide.
Install the dipstick guide with the bolt.
Install the dipstick.
| 15. INSTALL FAN SHROUD |
Install the fan pulley to the fan bracket.
Place the shroud together with the coupling fan between the radiator and engine.
Temporarily install the fluid coupling fan to the fan bracket with the 4 nuts. Tighten the nuts as much as possible by hand.
![]() |
Attach the shroud's claws to the radiator as shown in the illustration.
Install the shroud with the 2 bolts.
Connect the reservoir hose to the upper radiator tank.
Install the fan and generator V-belt.
![]() |
Tighten the 4 nuts of the fluid coupling fan.
| 16. INSTALL FAN & GENERATOR V BELT |
![]() |
Set the V belt onto every part.
While turning the belt tensioner counterclockwise, remove the pin.
![]() |
After installing the belt, check that it fits properly in the ribbed grooves.
| 17. CONNECT OUTLET RADIATOR HOSE |
| 18. CONNECT INLET RADIATOR HOSE |
| 19. INSTALL AIR CLEANER ASSEMBLY |
![]() |
Install the air cleaner case with the 2 bolts.
Install the air cleaner element onto the air cleaner case.
![]() |
Install the air cleaner cap.
Fasten the 4 hook clamps.
Connect the MAF meter connector.
Attach the wire harness clamp.
| 20. INSTALL AIR CLEANER HOSE ASSEMBLY |
![]() |
Install the air cleaner hose with the 2 clamps.
Connect the vacuum hose and ventilation hose.
| 21. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 22. ADD ENGINE COOLANT |
Add engine coolant.
| Item | Specified Condition |
| w/ Trailer Towing System | 13.0 liters (13.7 US qts, 11.4 Imp. qts) |
| w/o Trailer Towing System | 12.1 liters (12.8 US qts, 10.6 Imp. qts) |
![]() |
Slowly pour coolant into the radiator reservoir until it reaches the FULL line.
Install the reservoir cap.
Press the inlet and outlet radiator hoses several times by hand, and then check the coolant level. If the coolant level is low, add coolant.
Install the radiator cap.
Start the engine and warm it up until the thermostat opens.
Maintain the engine speed at 2000 to 2500 rpm.
Press the inlet and outlet radiator hoses several times by hand to bleed air.
Stop the engine, and wait until the engine coolant cools down to ambient temperature.
![]() |
Check that the coolant level is between the FULL and LOW lines.
If the coolant level is below the LOW line, repeat all of the procedures above.
If the coolant level is above the FULL line, drain coolant so that the coolant level is between the FULL and LOW lines.
| 23. INSPECT FOR COOLANT LEAK |
![]() |
Fill the radiator with coolant and attach a radiator cap tester.
Warm up the engine.
Using the radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17 psi), and check that the pressure does not drop.
If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and head.
| 24. INSPECT FOR EXHAUST GAS LEAK |
| 25. INSTALL FRONT FENDER APRON SEAL REAR LH |
Install the fender apron seal with the 5 clips.
| 26. INSTALL FRONT FENDER APRON SEAL LH |
Install the fender apron seal with the 6 clips.
| 27. INSTALL FRONT FENDER APRON SEAL REAR RH |
Install the fender apron seal with the 5 clips.
| 28. INSTALL FRONT FENDER APRON SEAL RH |
Install the fender apron seal with the 6 clips.
| 29. INSTALL NO. 1 ENGINE UNDER COVER |
![]() |
Hook the engine under cover to the vehicle body as shown in the illustration.
Install the 3 screws and 5 bolts.
| 30. INSTALL V-BANK COVER SUB-ASSEMBLY |
![]() |
Attach the 2 V-bank cover hooks to the bracket. Then align the 2 V-bank cover grommets with the 2 pins, and press down on the V-bank cover to attach the pins.