Home › TRANSMISSION · A760E AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION SYSTEM

AUTOMATIC TRANSMISSION SYSTEM > Pattern Select Switch Circuit

for Preparation Click here


DESCRIPTION

The ECM receives tow/haul pattern select switch information and performs tow/haul control.
While tow/haul control is operating, in contrast to normal mode, low gears are used to increase engine braking and towing power, reduce frequent shifts, and improve driveability. Tow/haul control includes throttle control, shift schedule control, wide open throttle shift timing control and AI-SHIFT control.
Tow/haul mode only operates when the shift lever is in D and the tow/haul pattern select switch is on.

HINT:
  1. The tow/haul pattern select switch is a momentary-type switch.
  2. In order to cancel tow/haul mode, push the tow/haul pattern select switch again or turn the ignition switch off.


WIRING DIAGRAM


C162870E12


INSPECTION PROCEDURE

1.INSPECT TOW/HAUL PATTERN SELECT SWITCH


    C210665E06
  1. for Column Shift Type:

    1. Disconnect the J25 transmission control switch connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      12 (P) - 9 (E)
      Tow/haul pattern select switch pushed
      Below 1 Ω
      12 (P) - 9 (E)
      Tow/haul pattern select switch not pushed
      10 kΩ or higher

      Text in Illustration 
      *a
      Component without harness connected
      (Transmission Control Switch)



    C210104E03
  1. for Floor Shift Type:

    1. Remove the rear upper console panel sub-assembly .

    2. Disconnect the J23 tow/haul pattern select switch connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      4 - 1
      Tow/haul pattern select switch pushed
      Below 1 Ω
      4 - 1
      Tow/haul pattern select switch not pushed
      10 kΩ or higher

      Text in Illustration 
      *a
      Component without harness connected
      (Tow/Haul Pattern Select Switch)
      Result 
      Result
      Proceed to
      OK
      A
      NG (for Column Shift Type)
      B
      NG (for Floor Shift Type)
      C

    4. Install the rear upper console panel sub-assembly .



B
REPLACE TRANSMISSION CONTROL SWITCH (COLUMN SHIFT SHIFT LEVER SUB-ASSEMBLY) (Click here)

C
REPLACE TOW/HAUL PATTERN SELECT SWITCH ASSEMBLY
A


2.CHECK HARNESS AND CONNECTOR (TOW/HAUL PATTERN SELECT SWITCH - BODY GROUND)


    C210666E07
  1. for Column Shift Type:

    1. Disconnect the J25 transmission control switch connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      J25-9 (E) - Body ground
      Always
      Below 1 Ω

      Text in Illustration 
      *a
      Front view of wire harness connector
      (to Transmission Control Switch)



    C210103E04
  1. for Floor Shift Type:

    1. Remove the rear upper console panel sub-assembly .

    2. Disconnect the J23 tow/haul pattern select switch connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      J23-1 - Body ground
      Always
      Below 1 Ω

      Text in Illustration 
      *a
      Front view of wire harness connector
      (to Tow/Haul Pattern Select Switch)

    4. Install the rear upper console panel sub-assembly .



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK HARNESS AND CONNECTOR (TOW/HAUL PATTERN SELECT SWITCH - ECM)


    C197708E50
  1. Disconnect the A24 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A24-51 (PWR) - Body ground
    Tow/haul pattern select switch pushed
    Below 1 Ω
    A24-51 (PWR) - Body ground
    Tow/haul pattern select switch not pushed
    10 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to ECM)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)