Home › TRANSMISSION · AB60E AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION SYSTEM

AUTOMATIC TRANSMISSION SYSTEM > Pattern Select Switch Circuit

for Preparation Click here


DESCRIPTION

The ECM receives tow/haul pattern select switch information and performs the tow/haul control.
While the tow/haul control is operating, in contrast to normal mode, low gears are used to increase engine braking and towing power, reduce frequent shifts, and improve driveability. The tow/haul control includes throttle control, shift schedule control, wide open throttle shift timing control and AI-SHIFT control.
Tow/haul mode only operates when the shift lever is in the D position and the tow/haul pattern select switch is ON.

HINT:
  1. The tow/haul pattern select switch is a momentary-type switch.
  2. In order to cancel tow/haul mode, push the tow/haul pattern select switch again or turn the ignition switch off.


WIRING DIAGRAM


C162870E10


INSPECTION PROCEDURE

1.INSPECT TOW/HAUL PATTERN SELECT SWITCH ASSEMBLY


    C159524E08
  1. for Column Shift Type:

    1. Disconnect the J25 transmission control switch connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      12 (P) - 9 (E)
      Tow/haul pattern select switch ON
      Below 1 Ω
      12 (P) - 9 (E)
      Tow/haul pattern select switch OFF
      10 kΩ or higher



    C162988E01
  1. for Floor Shift Type:

    1. Remove the rear upper console panel sub-assembly .

    2. Disconnect the J23 tow/haul pattern select switch connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      4 - 1
      Tow/haul pattern select switch ON
      Below 1 Ω
      4 - 1
      Tow/haul pattern select switch OFF
      10 kΩ or higher

      Result 
      Result
      Proceed to
      OK
      A
      NG (for Column Shift Type)
      B
      NG (for Floor Shift Type)
      C

    4. Install the rear upper console panel sub-assembly .



B
REPLACE COLUMN SHIFT SHIFT LEVER SUB-ASSEMBLY (TRANSMISSION CONTROL SWITCH) (Click here)

C
REPLACE TOW/HAUL PATTERN SELECT SWITCH ASSEMBLY
A


2.CHECK HARNESS AND CONNECTOR (TOW/HAUL PATTERN SELECT SWITCH - BODY GROUND)


    C159066E06
  1. for Column Shift Type:

    1. Disconnect the J25 transmission control switch connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      J25-9 (E) - Body ground
      Always
      Below 1 Ω



    C162989E01
  1. for Floor Shift Type:

    1. Remove the rear upper console panel sub-assembly .

    2. Disconnect the J23 tow/haul pattern select switch connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      J23-1 - Body ground
      Always
      Below 1 Ω

    4. Install the rear upper console panel sub-assembly .



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK HARNESS AND CONNECTOR (TOW/HAUL PATTERN SELECT SWITCH - ECM)


    C159423E56
  1. Disconnect the A24 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A24-51 (PWR) - Body ground
    Tow/haul pattern select switch ON
    Below 1 Ω
    A24-51 (PWR) - Body ground
    Tow/haul pattern select switch OFF
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)