Home › ENGINE · 1UR-FE › ENGINE MECHANICAL › FRONT CRANKSHAFT OIL SEAL

FRONT CRANKSHAFT OIL SEAL > REMOVAL

for Preparation Click here



1. REMOVE V-BANK COVER SUB-ASSEMBLY


    A214822E01
  1. Raise the front of the V-bank cover to detach the 2 pins. Then remove the 2 V-bank cover hooks from the bracket, and remove the V-bank cover.



2. REMOVE NO. 1 ENGINE UNDER COVER


    A150108
  1. Remove the 3 screws and 5 bolts.

  1. Unhook the engine under cover from the vehicle body as shown in the illustration.



3. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

HINT:
Collect the coolant in a container and dispose of it according to the regulations in your area.

  1. Loosen the radiator drain cock plug.

  1. Remove the radiator cap. Then drain the coolant from the radiator.

  1. Loosen the 2 cylinder block drain cock plugs. Then drain the coolant from the engine.



  1. Tighten the 2 cylinder block drain cock plugs.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf }



    A215892E01

  1. Tighten the radiator drain cock plug by hand.



4. REMOVE INLET RADIATOR HOSE


    A215577
  1. Remove the radiator hose.



5. REMOVE FAN AND GENERATOR V BELT


    A163770E01
  1. While turning the belt tensioner counterclockwise, align the service hole for the belt tensioner and the belt tensioner fixing position, and then insert a bar of φ 5 mm (0.197 in.) into the service hole to fix the belt tensioner in place.

    HINT:
    The pulley bolt for the belt tensioner has a left-hand thread.

  1. Remove the V belt.



6. REMOVE FAN SHROUD


    A217580
  1. Loosen the 4 nuts holding the fluid coupling fan

  1. Remove the fan and generator V-belt (Click here).

  1. Disconnect the reservoir hose from the upper radiator tank.



    A215579
  1. w/ Trailer Towing System:
    Detach the claw to open the No. 1 flexible hose clamp.



    A151821
  1. Remove the 2 bolts holding the fan shroud.

  1. Remove the 4 nuts of the fluid coupling fan, and then remove the shroud together with the fluid coupling fan.

    NOTICE:
    Be careful not to damage the radiator core.

  1. Remove the fan pulley from the fan bracket.



7. DISCONNECT FRONT STABILIZER BAR


    A163772
  1. Remove the 4 bolts, 2 stabilizer brackets and 2 stabilizer bushes. Then disconnect the stabilizer bar.



8. DISCONNECT COOLER COMPRESSOR ASSEMBLY


    A163332
  1. Remove the 2 bolts, 2 nuts and 2 stud bolts, and disconnect the cooler compressor.

    HINT:
    It is not necessary to completely remove the compressor. With the hoses connected to the compressor, hang the compressor on the vehicle body with a rope.



9. REMOVE OIL PRESSURE SENDER GAUGE ASSEMBLY


    A163657
  1. Disconnect the sender gauge connector.



    A162467
  1. Remove the oil pressure sender gauge.



10. REMOVE WATER BY-PASS PIPE (w/ Oil Cooler)


A210013
  1. Remove the 2 bolts.

  1. Disconnect the 4 water hoses and remove the water by-pass pipe.



11. REMOVE NO. 1 OIL COOLER BRACKET (w/ Oil Cooler)


    A163672
  1. Remove the 2 nuts and bracket.

  1. Disconnect the ground wire from the cylinder block.



12. REMOVE OIL FILTER BRACKET SUB-ASSEMBLY


    A214841
  1. Remove the 2 bolts, 2 nuts and filter bracket.



    A162470
  1. Remove the 2 O-rings.



13. REMOVE CRANKSHAFT PULLEY


    A164228E01
  1. Using SST, remove the crankshaft pulley set bolt.

    SST
    09213-70011  
    09330-00021  

  1. Temporarily install the pulley set bolt to the crankshaft until 2 or 3 threads are engaged.



    A164229E01
  1. Using the pulley set bolt and SST, remove the crankshaft pulley.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05010, 09954-05011)



14. REMOVE CRANKSHAFT TIMING GEAR KEY


    A214555E01
  1. Remove the crankshaft timing gear key from the crankshaft.



15. REMOVE FRONT CRANKSHAFT OIL SEAL


    A214556
  1. Using a screwdriver, pry out the oil seal.

    NOTICE:
    Do not damage the surface of the oil seal press fit hole and crankshaft.

    HINT:
    Tape the screwdriver tip before use.