REAR SEAT ASSEMBLY (for CrewMax RH Side) > REASSEMBLY |
| 1. INSTALL SEAT LOCK CONTROL CABLE SUB-ASSEMBLY RH |
![]() |
Install the control cable to the seatback frame.
Connect the 2 cables.
| 2. INSTALL REAR SEAT CUSHION SUPPORT ASSEMBLY |
![]() |
Install the cushion support with the 6 nuts.
| 3. INSTALL REAR SEATBACK FRAME SUB-ASSEMBLY RH |
![]() |
Using a T45 "TORX" socket, install the frame with the 5 bolts.
| 4. INSTALL RECLINING ADJUSTER INSIDE COVER RH |
![]() |
Attach the claw to install the cover.
Install the 2 screws.
| 5. INSTALL RECLINING ADJUSTER INSIDE COVER LH |
![]() |
Attach the claw to install the cover.
Install the 2 screws.
| 6. INSTALL REAR SEAT CUSHION MOULDING RH |
![]() |
Attach the 2 claws to install the moulding.
Install the 3 screws.
| 7. INSTALL REAR SEAT CUSHION MOULDING LH |
![]() |
Attach the 2 claws to install the moulding.
Install the 3 screws.
| 8. INSTALL REAR SEAT CUSHION SPRING ASSEMBLY RH |
![]() |
Install the 2 bushes to the cushion spring. Then using a T45 "TORX" socket, install the 2 bolts.
Install the 2 bolts.
| 9. INSTALL SEPARATE TYPE REAR SEATBACK COVER RH |
Using hog ring pliers, install the seatback cover to the seatback pad with new hog rings.
| 10. INSTALL REAR SEATBACK COVER WITH PAD RH |
Attach the hooks to install the seatback cover (with pad).

| 11. INSTALL LOWER REAR SEATBACK COVER SUB-ASSEMBLY RH |
![]() |
Using hog ring pliers, install the seatback cover with new hog rings.
| 12. INSTALL REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY RH |
![]() |
Connect the cable in the order shown in the illustration to install the lever.
![]() |
Install the 2 screws.
| 13. INSTALL REAR SEATBACK LOCK STRIKER COVER RH |
![]() |
Attach the 2 claws to install the cover.
| 14. INSTALL REAR SEAT HEADREST SUPPORT |
![]() |
Attach the 4 claws to install the 2 supports.
| 15. INSTALL REAR SEAT HEADREST ASSEMBLY RH |
| 16. INSTALL REAR SEATBACK COVER |
![]() |
Attach the 4 claws to install the cover.
| 17. INSTALL REAR SEATBACK BOARD RH |
![]() |
Attach the 2 clips to install the seatback board.
Install the 4 screws.
| 18. INSTALL REAR SEAT CUSHION MOULDING REAR RH |
![]() |
Attach the 2 claws in the order shown in the illustration to install the moulding.
Install the screw.
| 19. INSTALL REAR SEAT CUSHION MOULDING REAR LH |
![]() |
Attach the 2 claws in the order shown in the illustration to install the moulding.
Install the screw.
| 20. INSTALL SEPARATE TYPE REAR SEAT CUSHION COVER RH |
Using hog ring pliers, install the seat cushion cover to the seat cushion pad with new hog rings.
| 21. INSTALL REAR SEAT CUSHION COVER WITH PAD RH |
Attach the hooks to install the seat cushion cover (with pad).
Install the seat belt with the bolt.

![]() |
Using hog ring pliers, install the rubber band of the seatback cover to the seat frame with new hog rings.