Home › BODY ELECTRICAL › DOOR LOCK › REAR DOOR LOCK (for CrewMax)

REAR DOOR LOCK (for CrewMax) > REMOVAL

for Preparation Click here



1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


3. REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG LH


    B166242
  1. Using a screwdriver, detach the 4 claws and remove the inside handle bezel.

    HINT:
    Tape the screwdriver tip before use.



4. REMOVE REAR UPPER DOOR ARMREST BASE PANEL LH


    B166243
  1. Using a screwdriver, detach the 2 clips and rear upper door armrest base panel. Then disconnect the connector.

    HINT:
    Tape the screwdriver tip before use.



5. REMOVE REAR DOOR FRAME GARNISH LH


    B169253
  1. Detach the 5 clips and remove the rear door frame garnish.



6. REMOVE REAR DOOR ARMREST COVER LH


7. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY LH


    B169254E01
  1. Remove the 2 screws.

  1. Using a clip remover, remove the clip.

  1. for Standard:

    1. Detach the 10 clips and remove the trim board.

  1. for 12 Speakers:

    1. Detach the 10 clips and remove the trim board. Then disconnect the connector.



    B165654E01
  1. Disconnect the 2 cables from the inside handle.

  1. Remove the inside handle.



8. REMOVE REAR NO. 2 DOOR TRIM BRACKET


    B169255
  1. Remove the 2 screws and bracket.



9. REMOVE REAR DOOR SERVICE HOLE COVER LH


    B169256
  1. Disconnect the connector and 5 clamps.

  1. Remove the rear door service hole cover.

    HINT:
    Remove the remaining tape on the door.



10. REMOVE REAR DOOR GLASS RUN LH


    B169257
  1. Remove the rear door glass run.



11. REMOVE REAR DOOR REAR LOWER WINDOW FRAME SUB-ASSEMBLY LH


    B169259
  1. Remove the 2 bolts and rear door rear lower window frame.

    HINT:
    Remove the frame through the service hole.

    NOTICE:
    Be careful when removing the bolts as the frame may fall and become damaged.



12. REMOVE REAR DOOR GLASS SUB-ASSEMBLY LH


B169260
  1. Temporarily install the power window regulator switch.

  1. Move the door glass until the bolts appear in the service holes.

  1. Remove the 2 bolts.

    NOTICE:
    Be careful when removing the bolts as the glass may fall and become damaged.

  1. Remove the rear door glass from the rear door window regulator as shown in the illustration.

    NOTICE:
    Do not damage the door glass.

  1. Remove the power window regulator switch.



13. REMOVE REAR DOOR LOCK ASSEMBLY LH


    B169263
  1. Disconnect the connector.

  1. Using a T30 "TORX" wrench, remove the 3 screws and door lock.

    HINT:
    Remove the door lock through the service hole.

    NOTICE:
    Be careful when removing the bolts as the door lock may fall and become damaged.



14. REMOVE REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH


    B169265
  1. Using a screwdriver, detach the claw.



    B169264E01
  1. Remove the rear door lock remote control cable.



15. REMOVE REAR DOOR INSIDE LOCKING CABLE ASSEMBLY LH


    B167681
  1. Using a screwdriver, detach the 3 claws.

    HINT:
    Tape the screwdriver tip before use.



    B167682E01
  1. Remove the rear door inside locking cable.