Home › RESTRAINTS › SEAT BELT › REAR CENTER SEAT OUTER BELT ASSEMBLY (for CrewMax)

REAR CENTER SEAT OUTER BELT ASSEMBLY (for CrewMax) > INSTALLATION

for Preparation Click here



1. INSTALL CENTER REAR SEAT OUTER BELT ASSEMBLY


B168891E01
  1. Install the outer belt with the bolt and nut.

    HINT:
    First install the bolt A, and then install the nut B.

    Torque:
    for bolt A:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }
    for nut B:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. Install the belt sensor with the 3 nuts.

    Torque:
    for nut C:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }



2. INSTALL REAR SEAT SHOULDER BELT HOLE COVER


B168890
  1. Install the seat belt as shown in the illustration.



    B168889
  1. Install the cover with the screw.



3. INSTALL REAR SEATBACK HINGE COVER


B165034
  1. Install the cover with the 2 screws.



4. INSTALL CENTER RECLINING ADJUSTER INSIDE COVER


B165033
  1. Attach the claw and hook to install the cover.

  1. Install the 2 screws.



5. INSTALL REAR SEATBACK COVER WITH PAD


  1. Using hog ring pliers, install the seatback cover (with pad) with new hog rings.


    B173326E02



  1. Attach the hooks to the seatback frame.


    B165028



    B171578
  1. Attach the 4 claws to install the bezel.



6. INSTALL LOWER REAR SEATBACK COVER SUB-ASSEMBLY LH


B165027E02
  1. Using hog ring pliers, install the seatback cover with new hog rings.



7. INSTALL REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY LH


    B165026E01
  1. Connect the cable in the order shown in the illustration to install the lever.



    B165024
  1. Install the 2 screws.



8. INSTALL REAR SEATBACK LOCK STRIKER COVER LH


B165023
  1. Attach the 2 claws to install the cover.



9. INSTALL REAR SEAT HEADREST SUPPORT


B165021
  1. Attach the 8 claws to install the 4 supports as shown in the illustration.



10. INSTALL CENTER REAR SEAT HEADREST ASSEMBLY


11. INSTALL REAR SEAT HEADREST ASSEMBLY LH


12. INSTALL REAR SEAT ARMREST ASSEMBLY


B165022
  1. Install the armrest with the 3 nuts.

    Torque:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }



13. INSTALL REAR SEATBACK BOARD LH


B165019
  1. Attach the 5 clips to install the seatback board.

  1. Install the 4 screws.



14. INSTALL REAR SEAT CUSHION COVER WITH PAD LH
  1. Attach the hooks to install the seat cushion cover (with pad).



  1. Install the seat belts with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B165014E02



    B165013E02
  1. Using hog ring pliers, install the rubber band of the seatback cover to the seat frame with new hog rings.



15. CONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY


B167995
  1. Connect the seat belt anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    HINT:
    The rear No. 1 seat inner belt is fixed with the same bolt as the rear center seat outer belt's anchor. Therefore, connect it when installing the rear No. 1 seat inner belt.



16. INSTALL REAR SEAT ASSEMBLY LH


B165010E01
  1. Install the rear seat with the 5 bolts.

    Torque:
    for bolt A:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }
    for bolt B:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    1. Be careful not to damage the vehicle body.
    2. The anchor part of the seat belt must not overlap the protruding part.



17. CONNECT REAR SEAT INNER BELT ASSEMBLY


B168895E01
  1. Connect the seat belt with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not overlap the anchor part of the seat belt and protruding parts of the vehicle body.