Home › BODY ELECTRICAL › NAVIGATION › NAVIGATION SYSTEM (for SD)

NAVIGATION SYSTEM (for SD) > OPERATION CHECK

for Preparation Click here



Check System Normal Condition
  1. If the cause of a symptom is any of the following, the corresponding symptom is normal; it is not a malfunction.

    Symptom
    Answer
    A longer route than expected is chosen.
    Depending on the road conditions, the navigation ECU may determine that a longer route is quicker.
    Even when distance priority is high, the shortest route is not shown.
    Some paths may not be advised due to safety concerns.
    When the vehicle is put into motion immediately after the engine starts, the navigation system deviates from the actual position.
    If the vehicle starts before the navigation system activates, the system may not react.
    When driving on certain types of roads, especially new roads, the vehicle position deviates from the actual position.
    When the vehicle is driving on new roads not available on the SD card, the system attempts to match it to another nearby road, causing the position mark to deviate.



  2. I100066
  3. The following symptoms are not a malfunction, but are caused by errors inherent in the GPS, gyro sensor, speed sensor and navigation ECU.

    1. The current position mark may be displayed on a nearby parallel road.



    2. I100067
    3. Immediately after a fork in the road, the current vehicle position mark may be displayed on the wrong road.



    4. I100068
    5. When the vehicle turns right or left at an intersection, the current vehicle position mark may be displayed on a nearby parallel road.



    6. I100069
    7. When the vehicle is carried, such as on a ferry, and the vehicle itself is not being driven, the current vehicle position mark may be displayed in the position where the vehicle was until a measurement can be performed by GPS.



    8. I100070
    9. When the vehicle is driven on a steep hill, the current vehicle position mark may deviate from the correct position.



    10. I100071
    11. When the vehicle makes a continuous turn of 360°, 720°, 1080°, etc., the current vehicle position mark may deviate from the correct position.



    12. I100072
    13. When the vehicle moves erratically, such as when making constant lane changes, the current vehicle position mark may deviate from the correct position.



    14. I038146E02
    15. When the ignition switch is turned to ACC or ON on a turntable while parking, the current vehicle position mark may not point in the correct direction. The same will occur when the vehicle starts to move.



    16. I100074
    17. When the vehicle is driven on a snowy road or a mountain path with tire chains installed or using a spare tire, the current vehicle position mark may deviate from the correct position.



    18. I100075
    19. When a tire is changed, the current vehicle position mark may deviate from the correct position.

      HINT:
      1. The diameter of the tire may change, causing a speed sensor error.
      2. Performing "tire change" in calibration mode will allow the system to correct the current vehicle position faster.


CHECK PANEL & STEERING SWITCH

HINT:
  1. The navigation receiver assembly panel switches and steering switches are checked in the following procedure.
  2. Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

  1. Enter diagnostic mode (Click here).



  2. E225777
  3. Select "Function Check/Setting" from the "Service Menu" screen.



  4. E225778
  5. Select "Panel&Steering Switch" from the "Function Check/Setting I" screen.



  6. E225786E01
  7. Panel & Steering Switch Check Mode
    Screen Description 
    Display
    Content
    *a: Switch condition
    "Pushed" is displayed when any switch is pushed
    *b: Number of switches pushed
    1. Number of switches pushed at once is displayed
    2. If more than 3 switches are pushed at once, "More than 3" is displayed
    *c: Rotary switch direction
    Direction of rotary switch is displayed

    1. Operate each switch and check that the number of switches pushed and the switch conditions are correctly displayed.

      NOTICE:
      When the "SETUP" switch is pressed and held for 3 seconds or more, diagnostic mode will be canceled.


CHECK TOUCH SWITCH

HINT:
  1. The touch switches on the screen are checked in the following procedure.
  2. Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

  1. Enter diagnostic mode (Click here).



  2. E225777
  3. Select "Function Check/Setting" from the "Service Menu" screen.



  4. E225779
  5. Select "Touch Switch" from the "Function Check/Setting I" screen.



  6. Touch Switch Check



      E176521
    1. Touch the display anywhere in the open area to perform the check when the "Touch Switch Check" screen is displayed.

      HINT:
      1. A "+" mark is displayed where the display is touched.
      2. The "+" mark remains on the display even after the finger is removed.


CHECK MICROPHONE & VOICE RECOGNITION

HINT:
  1. The microphone and microphone input level are checked in the following procedure.
  2. Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

  1. Enter diagnostic mode (Click here).



  2. E225777
  3. Select "Function Check/Setting" from the "Service Menu" screen.



  4. E225780
  5. Select "Mic&Voice Recognition" from the "Function Check/Setting I" screen.



  6. E187218E13
  7. Microphone&Voice Recognition Check
    Screen Description 
    Display
    Content
    *a: Microphone input level meter
    Monitors the microphone input level every 0.1 seconds and displays the results in 8 different levels.
    *b: Recording switch
    Starts recording.
    *c: Stop switch
    Stops recording and playing.
    *d: Play switch
    Plays the recorded voice.
    *e: Recording indicator
    Comes on while recording.

    1. When speaking into the microphone, check that the microphone input level meter changes according to the input level.

      HINT:
      The microphone is active at all times when this screen is displayed.

    2. Push the recording switch and perform voice recording.

      HINT:
      1. Select the recording switch with the blower motor of the air conditioning system stopped. If an outlet of the air conditioning system is facing the microphone, noise may be recorded.
      2. While recording or playing, the switches other than the stop switch cannot be pushed.
      3. When no recording is present, the play switch cannot be pushed.
      4. Recording will stop after 5 seconds or when the stop switch is pushed.

    3. Check that the recording indicator remains on while recording and that the recording can be played normally.


CHECK COLOR BAR

HINT:
  1. The display color on the screen is checked in the following procedure.
  2. Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

  1. Enter diagnostic mode (Click here).



  2. E225777
  3. Select "Function Check/Setting" from the "Service Menu" screen.



  4. E225781
  5. Select "Color Bar" from the "Function Check/Setting I" screen.



  6. Color Bar Check Mode



      E226305
    1. Select a color bar from the "Color Bar Check Mode" screen.

    2. Check the display color.

      HINT:
      1. The entire screen turns to the color or stripe selected.
      2. Touching the display will return to the "Color Bar Check Mode" screen.


CHECK GPS & VEHICLE SENSORS

HINT:
  1. GPS information, vehicle signals and sensor signals are checked in the following procedure.
  2. Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

  1. Enter diagnostic mode (Click here).



  2. E225777
  3. Select "Function Check/Setting" from the "Service Menu" screen.



  4. E225782
  5. Select "GPS&Vehicle Sensors" from the "Function Check/Setting I" screen.



  6. E225775E01
  7. GPS Information
    *a: Satellite Information Description 
    Display
    Content
    No.
    Number of the target GPS satellite.
    Elv
    Elevation angle of the target GPS satellite.
    Azm
    Direction of the target GPS satellite.
    LVL
    The GPS signal level.
    *b: Receiving Condition Description 
    Display
    Content
    P
    The system is using the GPS signal for location.
    T
    The system is tracking the GPS signal for location.
    U
    The system is receiving a GPS signal, but is not using it for location.
    -
    The system cannot receive a GPS signal (when searching for a GPS signal).
    *c: Measurement Status Description 
    Display
    Content
    OK (H3D)
    High accuracy 3-dimensional location method is being used.
    OK (H2D)
    High accuracy 2-dimensional location method is being used.
    OK (3D)
    3-dimensional location method is being used.
    OK (2D)
    2-dimensional location method is being used.
    NG
    Location data cannot be used.
    error
    Reception error has occurred.
    -
    Any other state.
    *d: Position Information Description 
    Display
    Content
    Position
    Latitude and longitude information on the current position is displayed.
    *e: Date Information Description 
    Display
    Content
    Date
    The date/time information obtained from GPS signals is displayed in Greenwich Mean Time (GMT).

    HINT:
    1. This screen is updated once per second.
    2. Information from a maximum of 12 satellites is displayed on the screen.


    1. When the "GPS Information" screen is displayed, check the GPS conditions.

  8. Select "Sensors Check" from the "GPS Information" screen.



  9. E226261E01
  10. Vehicle Sensors
    Screen Description 
    Display
    Content
    *a: Vehicle signal
    Vehicle speed signal condition is displayed.
    *b: Sensor signal
    Gyro sensor output condition is displayed.

    HINT:
    This screen is updated once per second.


    1. Check all the signals and sensors when vehicle signal information is displayed.


CHECK VEHICLE SIGNAL

HINT:
  1. Vehicle signals received by the navigation receiver assembly are checked in the following procedure.
  2. Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

  1. Enter diagnostic mode (Click here).



  2. E225777
  3. Select "Function Check/Setting" from the "Service Menu" screen.



  4. E225783
  5. Select "Vehicle Signal" from the "Function Check/Setting I" screen.



  6. E235191
  7. Vehicle Signal Check Mode
    Screen Description 
    Display
    Content
    IG
    Ignition switch OFF state is displayed.
    PKB
    Parking brake ON/OFF state is displayed.
    REV
    Reverse signal ON/OFF state is displayed.
    SPEED
    Vehicle speed is displayed in km/h.
    TAIL
    Tail signal (Light control switch) ON/OFF state is displayed.

    HINT:
    1. Only items sending vehicle signals will be displayed.
    2. This screen displays vehicle signals input to the radio and display receiver assembly.
    3. This screen is updated once per second when vehicle input signals change.


    1. When the "Vehicle Signal Check Mode" screen is displayed, check all the vehicle signal conditions.


CHECK HANDSFREE VOICE QUALITY AND VOLUME SETTING

HINT:
  1. The handsfree volume of a "Bluetooth" compatible phone can be adjusted using the following procedure.
  2. Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

  1. Enter diagnostic mode (Click here).



  2. E225777
  3. Select "Function Check/Setting" from the "Service Menu" screen.



  4. E225784
  5. Select "HF Voice Quality Setting" from the "Function Check/Setting I" screen.



  6. E225788E01
  7. Hands-Free Voice Quality Setting (Receive/Send Voice Level adjustment)
    Screen Description 
    Display
    Content
    *a: Receive voice level adjustment
    Setting for the voice level received from "Bluetooth" compatible phones.
    *b: Send voice level adjustment
    Setting for the voice level sent from "Bluetooth" compatible phones.

    NOTICE:
    Sound quality may deteriorate when the receive voice or send voice level is changed more than necessary. For this reason, check that the receive voice or send voice quality is still acceptable after changing this setting.


    1. If the voice level is low, press the up button, and if the voice level is loud, press the down button.

      HINT:
      1. Settings will be applied when the up or down button is selected.
      2. The receive voice level adjustment ranges from -5 to +1.
      3. The send voice level adjustment ranges from -5 to +4.
      4. The initial level is "0".



  8. E228924E01
  9. Hands-Free Voice Quality Setting (Voice Quality Type adjustment)
    Screen Description 
    *a
    Numeric keypad
    *b
    Setting button
    *c
    Reset button

    1. If necessary, refer to the table below to adjust the voice quality type with the numeric keypad.

    2. When adjusting the settings, use the number pad on the screen to input the voice quality type according to the table.

      Settings 
      Parameter
      Target Phenomenon
      Voice Quality Type
      Positive Effects of Changing Voice Quality
      Negative Effects of Changing Voice Quality
      A
      (Noise)
      The change in background noise the other party hears becomes unpleasant.
      1000
      The change in background noise the other party hears is reduced.
      Background noise when not talking becomes large.
      B
      (Noise)
      The volume of the noise the other party hears temporarily becomes large.
      2000
      The temporary noise is reduced.
      The volume of voice may drop temporarily.
      C
      (Echo)
      The other party hears weak echoes.
      0100
      The amount of echo is reduced (low level).
      Sound quality of the other party deteriorates (low level).
      D
      (Echo)
      The other party hears strong echoes.
      0200
      The amount of echo is reduced (high level).
      Sound quality of the other party deteriorates (high level).
      E
      (Quality)
      The other party hears harsh noises.
      0010
      Sound the other party hears becomes soft.
      Sound the other party hears becomes muffled.
      F
      (Quality)
      You hear harsh noises.
      0020
      Sound you hear becomes soft.
      Sound you hear becomes muffled.

      Settings (When multiple phenomena occurred) 
      Parameter
      Target Phenomenon
      Voice Quality Type
      Positive Effects of Changing Voice Quality
      Negative Effects of Changing Voice Quality
      A+C
      The change in background noise the other party hears becomes unpleasant and the other party hears weak echoes.
      1100
      1. The change in background noise the other party hears is reduced.
      2. The amount of echo is reduced (low level).
      1. Background noise when not talking becomes large.
      2. Sound quality of the other party deteriorates (low level).
      A+D
      The change in background noise the other party hears becomes unpleasant and the other party hears strong echoes.
      1200
      1. The change in background noise the other party hears is reduced.
      2. The amount of echo is reduced (high level).
      1. Background noise when not talking becomes large.
      2. Sound quality of the other party deteriorates (high level).
      B+C
      The volume of the noise the other party hears temporarily becomes large and the other party hears weak echoes.
      2100
      1. The temporary noise is reduced.
      2. The amount of echo is reduced (low level).
      1. The volume of voice may drop temporarily.
      2. Sound quality of the other party deteriorates (low level).
      B+D
      The volume of the noise the other party hears temporarily becomes large and the other party hears strong echoes.
      2200
      1. The temporary noise is reduced.
      2. The amount of echo is reduced (high level).
      1. The volume of voice may drop temporarily.
      2. Sound quality of the other party deteriorates (high level).
      C+E
      The other party hears weak echoes and harsh noises.
      0110
      1. The amount of echo is reduced (low level).
      2. Sound the other party hears becomes soft.
      1. Sound quality of the other party deteriorates (low level).
      2. Sound the other party hears becomes muffled.
      C+F
      The other party hears weak echoes and you hear harsh noises.
      0120
      1. The amount of echo is reduced (low level).
      2. Sound you hear becomes soft.
      1. Sound quality of the other party deteriorates (low level).
      2. Sound you hear becomes muffled.

      HINT:
      1. The default value is "0000".
      2. Settings will be applied when the setting button is selected.
      3. If voice quality type values that are not in the table are input, the setting will not be applied and a positive effect may not be gained.
      4. If the quality of phone calls decreases due to the changed settings, return the settings to "0000" by pressing the "INIT" switch.