Home › TRANSMISSION ยท A750E AUTOMATIC TRANSMISSION › OIL COOLER

OIL COOLER > INSTALLATION

for Preparation Click here



1. INSTALL TRANSMISSION OIL COOLER ASSEMBLY


C157012E03
  1. Coat 2 new O-rings with ATF, and install them to the transmission oil cooler.

  1. Align the transmission oil cooler with the transmission oil cooler spacer and assemble them with the 3 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Connect the 2 transmission oil cooler hoses to the transmission oil cooler spacer with the 2 clips.



    C161815E05
  1. Temporarily install the transmission oil cooler with transmission oil cooler spacer with bolt A.

  1. Install the bolt B and tighten it to the specified torque. Then tighten bolt A to the specified torque.

    Torque:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf }

  1. Connect the 2 transmission oil cooler hoses with the 2 clips.

    HINT:
    Make sure the pinching portion of each clip is facing the direction shown in the illustration.



2. CONNECT WATER BY-PASS PIPE ASSEMBLY


C157031E02
  1. Connect the 2 water by-pass hoses with the 2 clips and install the water by-pass pipe with the bolt.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }

    HINT:
    Make sure the pinching portion of each clip is facing the direction shown in the illustration.



3. INSTALL HOSE HEAT PROTECTOR


C161816
  1. Install the hose heat protector with the bolt.

    Torque:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf }



4. INSTALL FRONT EXHAUST PIPE ASSEMBLY
  1. Install a new gasket and the front exhaust pipe to the exhaust manifold RH with 3 new nuts.

    Torque:
    54 N*m{ 554 kgf*cm , 40 ft.*lbf }



5. ADD ENGINE COOLANT
  1. Add engine coolant.

    Standard capacity:
    10.7 liters (11.3 US qts, 9.4 Imp. qts)

    NOTICE:
    Do not substitute plain water for engine coolant.

    HINT:
    1. TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).
    2. Press the No. 1 and No. 2 radiator hoses several times by hand, and then check the coolant level. If the coolant level is low, add coolant.

  1. Slowly pour coolant into the radiator reservoir until it reaches the FULL line.

  1. Install the reservoir cap.

  1. Install the radiator cap.*1

  1. Start the engine and stop it immediately.*2

  1. Allow approximately 10 seconds to pass. Then remove the radiator cap and check the coolant level. If the coolant level has decreased, add coolant.*3

  1. Repeat steps *1, *2 and *3 until the coolant level does not decrease.

    HINT:
    Be sure to perform this step while the engine is cold, as air in the inlet radiator hose will flow into the radiator if the engine is warmed up and the thermostat opens.

  1. Install the radiator cap.*4

  1. Set the air conditioning as follows.*5
    Measurement Condition 
    Item
    Condition
    Fan speed
    Any setting except off
    Temperature
    Toward WARM
    Air conditioning switch
    Off

  1. Start the engine, warm it up until the thermostat opens, and then continue to run the engine for several minutes to circulate the coolant.*6

    CAUTION:
    1. Wear protective gloves. Hot areas on the parts may injure your hands.
    2. Be careful of the fan.
    3. Be careful as the engine, radiator and radiator hoses are hot and can cause burns.

    NOTICE:
    1. Immediately after starting the engine, if the radiator reservoir does not have any coolant, perform the following: 1) stop the engine, 2) wait until the coolant has cooled down, and 3) add coolant until the coolant is filled to the FULL line.
    2. Do not start the engine when there is no coolant in the radiator reservoir.
    3. Pay attention to the needle of the engine coolant temperature receiver gauge. Make sure that the needle does not show an abnormally high temperature.
    4. If there is not enough coolant, the engine may burn out or overheat.

    HINT:
    1. Press the inlet and outlet radiator hoses several times by hand to bleed air while warming up the engine.
    2. The thermostat opening timing can be confirmed by pressing the outlet radiator hose by hand and checking when the engine coolant starts to flow inside the hose.

  1. Stop the engine, wait until the engine coolant cools down to ambient temperature. Then remove the radiator cap and check the coolant level.*7

    CAUTION:
    Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. If the coolant level has decreased, add coolant and warm up the engine until the thermostat opens.*8

  1. If the coolant level has not decreased, check that the coolant level in the radiator reservoir is at the FULL line.
    If the coolant level is below the FULL line, repeat steps *4 through *8.
    If the coolant level is above the FULL line, drain coolant until the coolant level reaches the FULL line.



6. ADJUST AUTOMATIC TRANSMISSION FLUID
  1. Adjust automatic transmission fluid (Click here).



7. INSPECT FOR AUTOMATIC TRANSMISSION FLUID LEAK


8. INSPECT FOR ENGINE COOLANT LEAK

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Fill the radiator with coolant and attach a radiator cap tester.

  1. Warm up the engine.

  1. Using the radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17 psi), and check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and head.



9. INSPECT FOR EXHAUST GAS LEAK