Home › ENGINE ยท 1UR-FE › EMISSION CONTROL › EGR VALVE

EGR VALVE > INSTALLATION

for Preparation Click here



1. INSTALL EGR VALVE BRACKET


    A214283
  1. Install the EGR valve bracket with the 3 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



2. INSTALL NO. 3 EGR PIPE SUB-ASSEMBLY


    A214285
  1. Install a new gasket and the No. 3 EGR pipe with the 2 nuts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



3. INSTALL EGR INLET


    A214284
  1. Install a new gasket and the EGR inlet with the 2 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    NOTICE:
    Make sure the gasket's claws are not caught between the EGR inlet and EGR valve.



4. INSTALL EGR VALVE ASSEMBLY


    A214282
  1. Install a new gasket to the intake manifold.



    A214876
  1. Install a new gasket to the No. 2 EGR pipe.



    A214286
  1. Temporarily install the EGR valve assembly to the intake manifold with the 2 bolts and 4 nuts.

    NOTICE:
    Be careful not to damage the intake manifold when installing the EGR valve assembly.



    A214286E01
  1. Using several steps, uniformly tighten the 2 bolts and 4 nuts in the sequence shown in the illustration.

    Torque:
    for bolt:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }
    for nut:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



5. CONNECT NO. 13 WATER BY-PASS HOSE


    A214276E01
  1. Connect the No. 13 water by-pass hose.

    HINT:
    The direction of the hose clamp is indicated in the illustration.



6. CONNECT NO. 12 WATER BY-PASS HOSE


    A214278E01
  1. Connect the No. 12 water by-pass hose.

    HINT:
    The direction of the hose clamp is indicated in the illustration.



7. INSTALL AIR CLEANER HOSE ASSEMBLY


    A214569
  1. Install the air cleaner hose with the 2 clamps.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }

  1. Connect the ventilation hose and vacuum sensing hose.



8. ADD ENGINE COOLANT
  1. Add engine coolant.

    Standard Capacity:
    Item
    Specified Condition
    w/ Trailer Towing System
    13.2 liters (13.9 US qts, 11.6 Imp. qts)
    w/o Trailer Towing System
    12.1 liters (12.8 US qts, 10.6 Imp. qts)

    NOTICE:
    Do not substitute plain water for engine coolant.

    HINT:
    TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology is a combination of low phosphates and organic acids).



    A151850E05
  1. Slowly pour coolant into the radiator reservoir until it reaches the FULL line.

  1. Install the reservoir cap.

  1. Press the inlet and outlet radiator hoses several times by hand, and then check the coolant level. If the coolant level is low, add coolant.

  1. Install the radiator cap.

  1. Start the engine and warm it up until the thermostat opens.

    HINT:
    The thermostat opening timing can be confirmed by pressing the radiator inlet hose by hand, and checking when the engine coolant starts to flow inside the hose.

  1. Maintain the engine speed at 2000 to 2500 rpm.

    NOTICE:
    1. Make sure that the radiator reservoir still has some coolant in it.
    2. Pay attention to the needle of the water temperature meter. Make sure that the needle does not show an abnormally high temperature.
    3. If there is not enough coolant, the engine may burn out or overheat.
    4. Immediately after starting the engine, if the radiator reservoir does not have any coolant, perform the following: 1) stop the engine, 2) wait until the coolant has cooled down, and 3) add coolant until the coolant is filled to the FULL line.
    5. Run the engine at 2000 rpm until the coolant level has stabilized.

  1. Press the inlet and outlet radiator hoses several times by hand to bleed air.

    CAUTION:
    1. Wear protective gloves.
    2. Be careful as the radiator hoses are hot.
    3. Keep your hands away from the fan.

  1. Stop the engine, and wait until the engine coolant cools down to ambient temperature.

    CAUTION:
    Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.



    A161780E01
  1. Check that the coolant level is between the FULL and LOW lines.
    If the coolant level is below the LOW line, repeat all of the procedures above.
    If the coolant level is above the FULL line, drain coolant so that the coolant level is between the FULL and LOW lines.



9. INSPECT FOR ENGINE COOLANT LEAK


A215893

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Fill the radiator with coolant and attach a radiator cap tester.

  1. Warm up the engine.

  1. Using the radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17 psi), and check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and head.



10. INSTALL V-BANK COVER SUB-ASSEMBLY


    A214821E01
  1. Attach the 2 V-bank cover hooks to the bracket. Then align the 2 V-bank cover grommets with the 2 pins, and press down on the V-bank cover to attach the pins.