Home › DRIVE LINE › DIFFERENTIAL › DIFFERENTIAL CARRIER OIL SEAL (for 3UR-FE, 3UR-FBE)

DIFFERENTIAL CARRIER OIL SEAL (for 3UR-FE, 3UR-FBE) > REPLACEMENT > Preparation



SST 
I000024
09308-10010
Oil Seal Puller


I000663
09316-12010
Transfer Bearing Replacer


I000032
09330-00021
Companion Flange Holding Tool


I000883
(09330-00030)
Pin


I000745
09649-17010
Steering Knuckle Tool


I010020
09930-00010
Drive Shaft Nut Chisel


I002108
09950-30012
Puller A Set


I002109
(09951-03010)
Upper Plate


I002110
(09953-03010)
Center Bolt


I002111
(09954-03010)
Arm


I002145
(09956-03030)
Adaptor 20


I002147
(09956-03050)
Adapter 24


I104580
09955-03050
Lower Plate 150 No.2




EQUIPMENT
Brass bar
-
Chisel
-
Dial indicator with magnetic base
-
Feeler gauge
-
Hammer
-
Micrometer
-
Needle nose pliers
-
Plastic hammer
-
Press
-
Prussian blue
-
Screw driver
-
Tape
-
Torque wrench
-


LUBRICANT / Front differential
Capacity
Oil type and viscosity
2.00 to 2.10 liters (2.12 to 2.21 US qts., 1.76 to 1.84 Imp. qts.)
Toyota Genuine Differential gear oil LT 75W-85 GL-5 or equivalent

LUBRICANT / Rear differential (1GR-FE, 1UR-FE)
Wheel base type
Cab type
Drive type
Capacity
Oil type and viscosity
3220 mm (10 ft. 6.8 in.)
Regular
2WD
4.00 to 4.10 liters (4.2 to 4.3 US qts., 3.5 to 3.6 Imp. qts.)
Toyota Genuine Differential gear oil LT 75W-85 GL-5 or equivalent
4WD
3700 mm (12 ft. 1.7 in.)
ALL
2WD
4.55 to 4.65 liters (4.8 to 4.9 US qts., 4.0 to 4.1 Imp. qts.)
4WD
4180 mm (13 ft. 8.6 in.)
2WD
4WD

LUBRICANT / Rear differential (3UR-FE, 3UR-FBE)
Wheel base type
Cab type
Drive type
Capacity
Oil type and viscosity
3220 mm (10 ft. 6.8 in.)
Regular
2WD
3.45 to 3.55 liters (3.65 to 3.75 US qts., 3.04 to 3.12 Imp. qts.)
Toyota Genuine Differential gear oil LT 75W-85 GL-5 or equivalent
4WD
3700 mm (12 ft. 1.7 in.)
Regular
2WD
3.55 to 3.65 liters (3.8 to 3.9 US qts., 3.1 to 3.2 Imp. qts.)
4WD
Double
2WD
4WD
CrewMax
2WD
3.70 to 3.80 liters (3.9 to 4.0 US qts., 3.2 to 3.3 Imp. qts.)
4WD
3.55 to 3.65 liters (3.8 to 3.9 US qts., 3.1 to 3.2 Imp. qts.)
4180 mm (13 ft. 8.6 in.)
Double
2WD
3.70 to 3.80 liters (3.9 to 4.0 US qts., 3.2 to 3.3 Imp. qts.)
4WD


RECOMMENDED TOOLS
J000321
09025-00010
Torque Wrench (30 kgf-cm)
-
I000322
09031-00030
Pin Punch
-
I000114
09905-00012
Snap Ring No. 1 Expander
-
I000115
09905-00013
Snap Ring Pliers
-


SSM
Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent
-
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
-
Toyota Genuine Adhesive 1360K, Three Bond 1360K or equivalent
-