SFI SYSTEM > TERMINALS OF ECM |
| CHECK ECM |

Measure the voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| A24-1 (BATT) - D74-81 (E1) | L - BR | Battery (for measuring battery voltage and for ECM memory) | Always | 11 to 14 V |
| D74-41 (+BM) - D74-81 (E1) | P - BR | Power source of throttle actuator | Always | 11 to 14 V |
| A24-28 (IGSW) - D74-81 (E1) | LG - BR | Ignition switch | Ignition switch ON | 11 to 14 V |
| A24-3 (+B) - D74-81 (E1) | GR - BR | Power source of ECM | Ignition switch ON | 11 to 14 V |
| A24-2 (+B2) - D74-81 (E1) | GR - BR | Power source of ECM | Ignition switch ON | 11 to 14 V |
| D74-58 (OC1+) - D74-57 (OC1-) | B - B-L | Camshaft oil control valve (OCV) (for Intake Side of Bank 1) | Idling | Pulse generation (see waveform 1) |
| D74-52 (OC2+) - D74-51 (OC2-) | L-B - R-B | Camshaft oil control valve (OCV) (for Intake Side of Bank 2) | Idling | Pulse generation (see waveform 1) |
| D74-56 (OE1+) - D74-55 (OE1-) | L-W - L-B | Camshaft oil control valve (OCV) (for Exhaust Side of Bank 1) | Idling | Pulse generation (see waveform 1) |
| D74-50 (OE2+) - D74-49 (OE2-) | L-R - L | Camshaft oil control valve (OCV) (for Exhaust Side of Bank 2) | Idling | Pulse generation (see waveform 1) |
| A24-34 (MREL) - D74-81 (E1) | W - BR | EFI relay | Ignition switch ON | 11 to 14 V |
| D74-74 (VG) - D74-75 (E2G) | L-Y - G-W | Mass air flow meter | Idling, shift lever in P or N, A/C switch OFF | 0.5 to 3.0 V |
| D74-73 (THA) - D74-98 (E2) | Y-B - BR | Intake air temperature sensor | Idling, intake air temperature 20°C (68°F) | 0.5 to 3.4 V |
| D74-76 (THW) - D74-98 (E2) | G-B - BR | Engine coolant temperature sensor | Idling, engine coolant temperature 80°C (176°F) | 0.2 to 1.0 V |
| D74-80 (VCTA) - D74-79 (ETA) | Y - L | Power source of throttle position sensor (specific voltage) | Ignition switch ON | 4.5 to 5.5 V |
| D74-78 (VTA1) - D74-79 (ETA) | R-Y - L | Throttle position sensor (for engine control) | Ignition switch ON, throttle valve fully closed | 0.5 to 1.1 V |
| Ignition switch ON, throttle valve fully open | 3.2 to 4.8 V | |||
| D74-77 (VTA2) - D74-79 (ETA) | Y-B - L | Throttle position sensor (for sensor malfunction detection) | Ignition switch ON, throttle valve fully closed | 2.1 to 3.1 V |
| Ignition switch ON, throttle valve fully open | 4.6 to 5.0 V | |||
| A24-55 (VPA) - A24-58 (EPA) | W - BE | Accelerator pedal position sensor (for engine control) | Ignition switch ON, accelerator pedal released | 0.5 to 1.1 V |
| Ignition switch ON, accelerator pedal fully depressed | 2.6 to 4.5 V | |||
| A24-56 (VPA2) - A24-60 (EPA2) | LG - P | Accelerator pedal position sensor (for sensor malfunction detection) | Ignition switch ON, accelerator pedal released | 1.2 to 2.0 V |
| Ignition switch ON, accelerator pedal fully depressed | 3.4 to 4.7 V | |||
| A24-57 (VCPA) - A24-58 (EPA) | B - BE | Power source of accelerator pedal position sensor (for VPA) | Ignition switch ON | 4.5 to 5.5 V |
| A24-59 (VCP2) - A24-60 (EPA2) | V - P | Power source of accelerator pedal position sensor (for VPA2) | Ignition switch ON | 4.5 to 5.5 V |
| D74-22 (HA1A) - D74-23 (E04) | L - W-B | A/F sensor heater | Idling with warm engine | Pulse generation (see waveform 2) |
| D74-22 (HA1A) - D74-23 (E04) | L - W-B | A/F sensor heater | Ignition switch ON | 11 to 14 V |
| D74-20 (HA2A) - D74-21 (E05) | G - W-B | A/F sensor heater | Idling with warm engine | Pulse generation (see waveform 2) |
| D74-20 (HA2A) - D74-21 (E05) | G - W-B | A/F sensor heater | Ignition switch ON | 11 to 14 V |
| D74-126 (A1A+) - D74-81 (E1) | G -BR | A/F sensor | Ignition switch ON | 3.3 V*1 |
| D74-125 (A1A-) - D74-81 (E1) | R - BR | A/F sensor | Ignition switch ON | 2.9 V*1 |
| D74-103 (A2A+) - D74-81 (E1) | P - BR | A/F sensor | Ignition switch ON | 3.3 V*1 |
| D74-102 (A2A-) - D74-81 (E1) | L - BR | A/F sensor | Ignition switch ON | 2.9 V*1 |
| D74-45 (HT1B) - D74-46 (E03) | G-B - W-B | Heated oxygen sensor heater | Idling | Below 3.0 V |
| D74-45 (HT1B) - D74-46 (E03) | G-B - W-B | Heated oxygen sensor heater | Ignition switch ON | 11 to 14 V |
| D74-44 (HT2B) - D74-46 (E03) | B - W-B | Heated oxygen sensor heater | Idling | Below 3.0 V |
| D74-44 (HT2B) - D74-46 (E03) | B - W-B | Heated oxygen sensor heater | Ignition switch ON | 11 to 14 V |
| D74-114 (OX1B) - D74-115 (EX1B) | G - L | Heated oxygen sensor | Engine speed maintained at 2500 rpm for 2 minutes after warming up sensor | Pulse generation (see waveform 3) |
| D74-112 (OX2B) - D74-113 (EX2B) | R - W | |||
| D74-86 (#10) - D74-43 (E01) | R-L - W-B | Fuel injector assembly | Ignition switch ON | 11 to 14 V |
| D74-109 (#20) - D74-43 (E01) | L - W-B | Idling | Pulse generation (see waveform 4) | |
| D74-85 (#30) - D74-43 (E01) | R - W-B | |||
| D74-108 (#40) - D74-43 (E01) | Y - W-B | |||
| D74-84 (#50) - D74-43 (E01) | G - W-B | |||
| D74-107 (#60) - D74-43 (E01) | R - W-B | |||
| D74-83 (#70) - D74-43 (E01) | W - W-B | |||
| D74-106 (#80) - D74-43 (E01) | R-B - W-B | |||
| D74-94 (KNK1) - D74-93 (EKNK) | R - G | Knock sensor | Engine speed maintained at 4000 rpm after warming up engine | Pulse generation (see waveform 5) |
| D74-117 (KNK2) - D74-116 (EKN2) | W - B | |||
| D74-96 (KNK3) - D74-95 (EKN3) | W - B | |||
| D74-119 (KNK4) - D74-118 (EKN4) | R - G | |||
| D74-92 (VV1+) - D74-91 (VV1-) | R - G | Variable valve timing (VVT) sensor (for Intake Side of Bank 1) | Idling | Pulse generation (see waveform 6) |
| D74-87 (VV2+) - D74-88 (VV2-) | R - Y | Variable valve timing (VVT) sensor (for Intake Side for Bank 2) | Idling | Pulse generation (see waveform 6) |
| D74-69 (EV1+) - D74-68 (EV1-) | R-L - B | Variable valve timing (VVT) sensor (for Exhaust Side of Bank 1) | Idling | Pulse generation (see waveform 17) |
| D74-64 (EV2+) - D74-65 (EV2-) | R-L - B | Variable valve timing (VVT) sensor (for Exhaust Side of Bank 2) | Idling | Pulse generation (see waveform 17) |
| D74-110 (NE+) - D74-111 (NE-) | W - Y | Crankshaft position sensor | Idling | Pulse generation (see waveform 6) |
| D74-40 (IGT1) - D74-81 (E1) | B-Y - BR | Ignition coil (ignition signal) | Idling | Pulse generation (see waveform 7) |
| D74-33 (IGT2) - D74-81 (E1) | L-Y - BR | |||
| D74-37 (IGT3) - D74-81 (E1) | B - BR | |||
| D74-34 (IGT4) - D74-81 (E1) | L-B - BR | |||
| D74-35 (IGT5) - D74-81 (E1) | G-R - BR | |||
| D74-36 (IGT6) - D74-81 (E1) | G - BR | |||
| D74-38 (IGT7) - D74-81 (E1) | G-W - BR | |||
| D74-39 (IGT8) - D74-81 (E1) | G-B - BR | |||
| D74-104 (IGF1) - D74-81 (E1) | G-B - BR | Ignition coil (ignition confirmation signal) | Ignition switch ON | 4.5 to 5.5 V |
| Idling | Pulse generation (see waveform 7) | |||
| D74-105 (IGF2) - D74-81 (E1) | R - BR | Ignition coil (ignition confirmation signal) | Ignition switch ON | 4.5 to 5.5 V |
| Idling | Pulse generation (see waveform 7) | |||
| D74-63 (PRG) - D74-81 (E1) | L-B - BR | Purge VSV | Ignition switch ON | 11 to 14 V |
| Idling | Pulse generation (see waveform 8) | |||
| A24-13 (SPD) - D74-81 (E1) | B - BR | Speed signal from combination meter | Driving at 20 km/h (12 mph) | Pulse generation (see waveform 9) |
| A24-46 (STA) - D74-81 (E1) | R - BR | Starter signal | Cranking | 5.5 V or more |
| D74-120 (NSW) - D74-81 (E1) | L - BR | Park/neutral position switch | Ignition switch ON, shift lever position not in P or N | 11 to 14 V |
| Ignition switch ON, shift lever in P or N | Below 3.0 V | |||
| A24-36 (STP) - D74-81 (E1) | SB - BR | Stop light switch | Brake pedal depressed | 7.5 to 14 V |
| Brake pedal released | Below 1.5 V | |||
| A24-35 (ST1-) - D74-81 (E1) | R - BR | Stop light switch (opposite to STP terminal) | Ignition switch ON, brake pedal depressed | Below 1.5 V |
| Ignition switch ON, brake pedal released | 7.5 to 14 V | |||
| D74-19 (M+) - D74-82 (ME01) | R - W-B | Throttle actuator | Idling with warm engine | Pulse generation (see waveform 10) |
| D74-18 (M-) - D74-82 (ME01) | G - W-B | Throttle actuator | Idling with warm engine | Pulse generation (see waveform 11) |
| A24-52 (FPC) - D74-81 (E1) | BE - BR | Fuel pump control | Ignition switch ON | Below 1.5 V |
| A24-24 (W) - D74-81 (E1) | P - BR | MIL | Ignition switch ON | Below 3.0 V |
| Idling | 11 to 14 V | |||
| A24-16 (TC) - D74-81 (E1) | V - BR | Terminal TC of DLC3 | Ignition switch ON | 11 to 14 V |
| A24-15 (TACH) - D74-81 (E1) | GR - BR | Engine speed | Idling | Pulse generation (see waveform 12) |
| A24-30 (VPMP) - D74-81 (E1) | V - BR | Vent valve (built into canister pump module) | Ignition switch ON | 11 to 14 V |
| A24-49 (MPMP) - D74-81 (E1) | W - BR | Leak detection pump (built into canister pump module) | Leak detection pump OFF | Below 3.0 V |
| Leak detection pump ON | 11 to 14 V | |||
| D74-67 (VCV1) - D74-98 (E2) | L - BR | Power source for sensor (specific voltage) | Ignition switch ON | 4.5 to 5.5 V |
| D74-66 (VCV2) - D74-98 (E2) | L - BR | Power source for sensor (specific voltage) | Ignition switch ON | 4.5 to 5.5 V |
| D74-121 (PPMP) - D74-98 (E2) | P - BR | Canister pressure sensor (built into canister pump module) | Ignition switch ON | 3.3 to 4.0 V |
| D74-32 (ALT) - D74-81 (E1) | R - BR | Generator | Ignition switch ON | 11 to 14 V |
| A24-10 (CANH) - D74-81 (E1) | GR - BR | CAN communication line | Ignition switch ON | Pulse generation (see waveform 13) |
| A24-11 (CANL) - D74-81 (E1) | W - BR | CAN communication line | Ignition switch ON | Pulse generation (see waveform 14) |
| D74-62 (ACIS) - D74-81 (E1) | L-Y - BR | VSV for ACIS (Acoustic Control Induction System) operation signal | Ignition switch ON | 11 to 14 V |
| D74-60 (HAI1) - D74-81 (E1) | B - BR | Air pump heater for secondary air injection system | AI heater operating | Below 1.5 V |
| D74-28 (AIRV) - D74-81 (E1) | BR - BR | Air switching valve for secondary air injection system | Ignition switch ON | 11 to 14 V |
| D74-54 (AIRP) - D74-81 (E1) | P - BR | Air pump control | Ignition switch ON | 11 to 14 V |
| D74-30 (AIDI) - D74-81 (E1) | G - BR | Diagnostic information signal for secondary air injection system | Secondary air injection system operating | Pulse generation (see waveform 16) |
| A24-54 (AIP) - D74-98 (E2) | Y - BR | Secondary air injection system pressure signal | Ignition switch ON | 3.0 to 3.6 V |
| A24-43 (ARV2) - D74-81 (E1) | V - BR | Air switching valve for secondary air injection system | Ignition switch ON | 11 to 14 V |
| D74-53 (ARP2) - D74-81 (E1) | P-L - BR | Air pump control | Ignition switch ON | 11 to 14 V |
| D74-29 (AID2) - D74-81 (E1) | G-Y - BR | Diagnostic information signal for secondary air injection system | Air injection system operating | Pulse generation (see waveform 16) |
| A24-53 (AIP2) - D74-98 (E2) | G - BR | Secondary air injection system pressure signal | Ignition switch ON | 3.0 to 3.6 V |
| D74-90 (G2) - D74- 89 (G2-) | R - B | Camshaft position sensor | Idling | Pulse generation (see waveform 15) |
| A24-14 (STSW) - D74-81 (E1) | BR - BR | Starter switch | Shift lever in P or N, cranking | 6.0 V or more |
| A24-41 (ACCR) - D74-81 (E1) | BR - BR | ACC relay control signal | Ignition switch ON → Cranking | 11 to 14 V → Below 1 V |
| D74-16 (STAR) - D74-81 (E1) | L - BR | Starter relay control | Ignition switch ON | Below 1.5 V |
| Cranking | 5.5 V or more | |||
| D74-72 (PSP) - D74-81 (E1) | G - BR | Power steering oil pressure sensor | Ignition switch ON | 0.5 to 4.5 V |
| D74-97 (PIM) - D74-98 (E2) | L-R - BR | Manifold absolute pressure sensor | Idling | 1.2 to 2.0 V |
| D74-48 (EGR1) - D74-81 (E1) | B - BR | EGR valve assembly | Engine racing with warm engine | Pulse generation (see waveform 18) |
| D74-1 (EGR2) - D74-81 (E1) | B-L - BR | EGR valve assembly | Engine racing with warm engine | Pulse generation (see waveform 19) |
| D74-24 (EGR3) - D74-81 (E1) | B-R - BR | EGR valve assembly | Engine racing with warm engine | Pulse generation (see waveform 18) |
| D74-47 (EGR4) - D74-81 (E1) | B-Y - BR | EGR valve assembly | Engine racing with warm engine | Pulse generation (see waveform 19) |
| A24-33 (ELS2) - D74-81 (E1) | B - BR | Electric load | Defogger switch on | 7.5 to 14 V |
| Defogger switch off | Below 1.5 V | |||
| A24-4 (ADJ1)*2 - Body ground | W-B - Body ground | Vehicle type designation wire harness | Always | Below 1 V |
![]() |
WAVEFORM 1:
| Terminal No. (Symbol) | Tool Setting | Condition |
| D74-58 (OC1+) - D74-57 (OC1-) | 5 V/DIV., 1 msec./DIV. | Idling |
| D74-52 (OC2+) - D74-51 (OC2-) | 5 V/DIV., 1 msec./DIV. | Idling |
| D74-56 (OE1+) - D74-55 (OE1-) | 5 V/DIV., 1 msec./DIV. | Idling |
| D74-50 (OE2+) - D74-49 (OE2-) | 5 V/DIV., 1 msec./DIV. | Idling |
![]() |
WAVEFORM 2:
| Terminal No. (Symbol) | Tool Setting | Condition |
| CH1: D74-22 (HA1A) - D74-23 (E04) | 5 V/DIV., 10 msec./DIV. | Idling with warm engine |
| CH2: D74-20 (HA2A) - D74-21 (E05) | 5 V/DIV., 10 msec./DIV. | Idling with warm engine |
![]() |
WAVEFORM 3:
| Terminal No. (Symbol) | Tool Setting | Condition |
| D74-114 (OX1B) - D74-115 (EX1B) | 0.2 V/DIV., 200 msec./DIV. | Engine speed maintained at 2500 rpm for 2 minutes after warming up sensor |
| D74-112 (OX2B) - D74-113 (EX2B) | 0.2 V/DIV., 200 msec./DIV. | Engine speed maintained at 2500 rpm for 2 minutes after warming up sensor |
![]() |
WAVEFORM 4:
| Terminal No. (Symbol) | Tool Setting | Condition |
| D74-86 (#10) - D74-43 (E01) | 20 V/DIV., 20 msec./DIV. | Idling |
| D74-109 (#20) - D74-43 (E01) | 20 V/DIV., 20 msec./DIV. | Idling |
| D74-85 (#30) - D74-43 (E01) | 20 V/DIV., 20 msec./DIV. | Idling |
| D74-108 (#40) - D74-43 (E01) | 20 V/DIV., 20 msec./DIV. | Idling |
| D74-84 (#50) - D74-43 (E01) | 20 V/DIV., 20 msec./DIV. | Idling |
| D74-107 (#60) - D74-43 (E01) | 20 V/DIV., 20 msec./DIV. | Idling |
| D74-83 (#70) - D74-43 (E01) | 20 V/DIV., 20 msec./DIV. | Idling |
| D74-106 (#80) - D74-43 (E01) | 20 V/DIV., 20 msec./DIV. | Idling |
![]() |
WAVEFORM 5:
| Terminal No. (Symbol) | Tool Setting | Condition |
| D74-94 (KNK1) - D74-93 (EKNK) | 1 V/DIV., 1 msec./DIV. | Engine speed maintained at 4000 rpm after warming up engine |
| D74-117 (KNK2) - D74-116 (EKN2) | 1 V/DIV., 1 msec./DIV. | Engine speed maintained at 4000 rpm after warming up engine |
| D74-96 (KNK3) - D74-95 (EKN3) | 1 V/DIV., 1 msec./DIV. | Engine speed maintained at 4000 rpm after warming up engine |
| D74-119 (KNK4) - D74-118 (EKN4) | 1 V/DIV., 1 msec./DIV. | Engine speed maintained at 4000 rpm after warming up engine |
![]() |
WAVEFORM 6:
| Terminal No. (Symbol) | Tool Setting | Condition |
| (a) D74-110 (NE+) - D74-111 (NE-) | 5 V/DIV., 20 msec./DIV. | Idling after engine warmed up |
| (b) D74-92 (VV1+) - D74-91 (VV1-) | 5 V/DIV., 20 msec./DIV. | Idling after engine warmed up |
| (c) D74-87 (VV2+) - D74-88 (VV2-) | 5 V/DIV., 20 msec./DIV. | Idling after engine warmed up |
![]() |
WAVEFORM 7:
| Terminal No. (Symbol) | Tool Setting | Condition |
| (a) D74-40 (IGT1) - D74-81 (E1) | 2 V/DIV., 20 msec./DIV. | Idling |
| (a) D74-33 (IGT2) - D74-81 (E1) | 2 V/DIV., 20 msec./DIV. | Idling |
| (a) D74-37 (IGT3) - D74-81 (E1) | 2 V/DIV., 20 msec./DIV. | Idling |
| (a) D74-34 (IGT4) - D74-81 (E1) | 2 V/DIV., 20 msec./DIV. | Idling |
| (a) D74-35 (IGT5) - D74-81 (E1) | 2 V/DIV., 20 msec./DIV. | Idling |
| (a) D74-36 (IGT6) - D74-81 (E1) | 2 V/DIV., 20 msec./DIV. | Idling |
| (a) D74-38 (IGT7) - D74-81 (E1) | 2 V/DIV., 20 msec./DIV. | Idling |
| (a) D74-39 (IGT8) - D74-81 (E1) | 2 V/DIV., 20 msec./DIV. | Idling |
| (b) D74-104 (IGF1) - D74-81 (E1) | 2 V/DIV., 20 msec./DIV. | Idling |
| (b) D74-105 (IGF2) - D74-81 (E1) | 2 V/DIV., 20 msec./DIV. | Idling |
![]() |
WAVEFORM 8:
| Terminal No. (Symbol) | Tool Setting | Condition |
| D74-63 (PRG) - D74-81 (E1) | 10 V/DIV., 20 msec./DIV. | Idling |
![]() |
WAVEFORM 9:
| Terminal No. (Symbol) | Tool Setting | Condition |
| A24-13 (SPD) - D74-81 (E1) | 2 V/DIV., 20 msec./DIV. | Driving at 20 km/h (12 mph) |
![]() |
WAVEFORM 10:
| Terminal No. (Symbol) | Tool Setting | Condition |
| D74-19 (M+) - D74-82 (ME01) | 5 V/DIV., 1 msec./DIV. | Idling with warm engine |
![]() |
WAVEFORM 11:
| Terminal No. (Symbol) | Tool Setting | Condition |
| D74-18 (M-) - D74-82 (ME01) | 5 V/DIV., 1 msec./DIV. | Idling with warm engine |
![]() |
WAVEFORM 12:
| Terminal No. (Symbol) | Tool Setting | Condition |
| A24-15 (TACH) - D74-81 (E1) | 5 V/DIV., 10 msec./DIV. | Idling |
![]() |
WAVEFORM 13:
| Terminal No. (Symbol) | Tool Setting | Condition |
| A24-10 (CANH) - D74-81 (E1) | 1 V/DIV., 10 μsec./DIV. | Engine stopped and ignition switch ON |
![]() |
WAVEFORM 14:
| Terminal No. (Symbol) | Tool Setting | Condition |
| A24-11 (CANL) - D74-81 (E1) | 1 V/DIV., 10 μsec./DIV. | Engine stopped and ignition switch ON |
![]() |
WAVEFORM 15:
| Terminal No. (Symbol) | Tool Setting | Condition |
| CH1: D74-110 (NE+) - D74-111 (NE-) | 5 V/DIV., 20 msec./DIV. | Idling after engine warmed up |
| CH2: D74-90 (G2) - D74-89 (G2-) | 5 V/DIV., 20 msec./DIV. | Idling after engine warmed up |
![]() |
WAVEFORM 16:
| Terminal No. (Symbol) | Tool Setting | Condition |
| D74-30 (AIDI) - D74-81 (E1) | 5 V/DIV., 50 msec./DIV. | Performing system check using Techstream (secondary air injection check) |
| D74-29 (AID2) - D74-81 (E1) | 5 V/DIV., 50 msec./DIV. | Performing system check using Techstream (secondary air injection check) |
![]() |
WAVEFORM 17:
| Terminal No. (Symbol) | Tool Setting | Condition |
| (a) D74-110 (NE+) - D74-111 (NE-) | 5 V/DIV., 20 msec./DIV. | Idling after engine warmed up |
| (b) D74-69 (EV1+) - D74-68 (EV1-) | 5 V/DIV., 20 msec./DIV. | Idling after engine warmed up |
| (c) D74-64 (EV2+) - D74-65 (EV2-) | 5 V/DIV., 20 msec./DIV. | Idling after engine warmed up |
![]() |
WAVEFORM 18:
| Terminal No. (Symbol) | Tool Setting | Condition |
| CH1: D74-48 (EGR1) - D74-81 (E1) | 10 V/DIV., 20 msec./DIV. | Engine racing with warm engine |
| CH2: D74-24 (EGR3) - D74-81 (E1) | 10 V/DIV., 20 msec./DIV. | Engine racing with warm engine |
![]() |
WAVEFORM 19:
| Terminal No. (Symbol) | Tool Setting | Condition |
| CH1: D74-1 (EGR2) - D74-81 (E1) | 10 V/DIV., 20 msec./DIV. | Engine racing with warm engine |
| CH2: D74-47 (EGR4) - D74-81 (E1) | 10 V/DIV., 20 msec./DIV. | Engine racing with warm engine |